DOWNLOAD Sony KP-43T75C / KP-53SV75C / KP-61SV75C Service Manual ↓ Size: 8.85 MB | Pages: 92 in PDF or view online for FREE

– 9 –

You may find it necessary to use some of the
following connector types during set up.

Standard TV cable and antenna cable

High quality video cable for enhanced
picture quality

Video - Yellow
Audio (Left) - White
Audio (Right) - Red

Some DVD Players are equipped with the
following three video connectors.

Y - Green
P

B

 (C

B

, C

b

 or B–Y) - Blue

P

R

 (C

R

, C

r

 or R–Y) - Red

Screw into connection.

Push into connection.

Align guides and
push into connection.

Push into connection.

Sony cable for CONTROL S connection. This
feature is exclusive to Sony products and
allow greater control of all Sony equipment.

To control other Sony equipment with the
projection TV’s remote control, connect the
CONTROL S IN jack of the equipment to the
CONTROL S OUT jack on the projection TV
with the CONTROL S cable.

Push into connection.

The connection you choose will depend on
the cable found in your home. Newer homes
will be equipped with standard coaxial cable
(see 

); older homes will probably have 300 -

ohm twin lead cable (see 

); still other

homes may contain both (see 

).

Use 75-ohm coaxial cable for improved
picture quality (see 

).

This is the simplest connection. Connection is
made directly from the cable or antenna to
the projection TV.

You may find it convenient to use the
following set up if your cable provider does
not feature local channels that you are able to
receive using an antenna.

Select Cable or ANT mode by pressing ANT
on the remote control.

Some pay cable TV systems use scrambled or
encoded signals that require a cable box* to
view all channels.
Also, set “Cable” to “Sí” in the Ajuste de
canal menu (page 25).

Some pay cable TV systems use scrambled or
encoded signals requiring a cable box* only for
certain channels (e.g. HBO, CNN,  etc.)

For this set up, you can switch between
scrambled channels (through your cable
box), and normal (CATV) channels by
pressing ANT on your remote control.
Notes:
• You may be able to program your Sony

remote control to operate your cable box.
(see “Operating a Cable Box” on page 32)

• During PIP or Canal favorito viewing, the

AUX input can only be viewed in the
main picture.

– 10 –

Attach the coaxial cable from the
incoming cable connection or antenna to
VHF/UHF IN on the VCR.

Using a coaxial cable, connect VHF/UHF
OUT on the VCR to VHF/UHF on the
projection TV.

Using AUDIO and S VIDEO* cables,
connect AUDIO and S VIDEO OUT on the
VCR to AUDIO and S VIDEO IN on the
projection TV (White-AUDIO Left, Red-
AUDIO Right**).

Connect the single (input) jack of the
splitter to the incoming cable connection,
and connect the other two (output) jacks
(using the coaxial cable) to IN on the cable
box and VHF/UHF on the projection TV.

Using a coaxial cable, connect OUT on the
cable box to VHF/UHF IN on the VCR.

Using AUDIO and S VIDEO* cables,
connect AUDIO and S VIDEO OUT on the
VCR to AUDIO and S VIDEO IN on the
projection TV (White-AUDIO Left, Red-
AUDIO Right**).

Note:
• To view scrambled channels through the

cable box, select the video input which the
cable box is connected to by pressing TV/
VIDEO.

* If your VCR is not equipped with S VIDEO, use

a VIDEO cable (yellow) instead of the S VIDEO
cable.

** If you are connecting a monaural VCR, connect

only the single audio output to the left (MONO)
input on the projection TV.

Use this connection to view a picture directly

from your camcorder.

Using AUDIO and S VIDEO* cables,

connect AUDIO and S VIDEO OUT on

the camcorder to AUDIO and S VIDEO

IN inside the drop-down panel on the

front of the projection TV (White-AUDIO

Left, Red-AUDIO Right**).

  Press VIDEO 2 to select the video inputs

from a camcorder.

* If your camcorder is not equipped with S

VIDEO, use a VIDEO cable (yellow) instead of
the S VIDEO cable.

** If you are connecting a monaural camcorder,

connect only the single audio output to the left
(MONO) input on the projection TV.

– 11 –

By connecting a second VCR to MONITOR
OUT, you can record a program being played
by the primary VCR to the second VCR or
perform tape editing and dubbing.

Connect the VCR intended for playback
using the connection instructions on page
6 of this manual.

Using an AUDIO/VIDEO cable, connect
AUDIO and VIDEO IN on the VCR
intended for recording to AUDIO and
VIDEO OUT of MONITOR OUT on the
projection TV.

Notes:
• Do not change the input signal while

editing through MONITOR OUT.

• When connecting a single VCR to the

projection TV: if VCR LINE OUT is
connected to VIDEO IN on the projection
TV, do not connect MONITOR OUT on
the projection TV to the VCR LINE
INPUT (see right). Doing so will cause
program interference and other viewing
problems.

LINE

OUT

IN

MONITOR
OUT

VIDEO IN

Using an AUDIO and S VIDEO cables,
connect AUDIO and S VIDEO IN on the
projection TV to AUDIO and S VIDEO OUT
on the DVD Player (White-AUDIO Left, Red-
AUDIO Right).

Using an AUDIO cable, connect AUDIO of
LINE OUT on the DVD Player to AUDIO of
VIDEO 3 IN on the projection TV (White-
AUDIO Left, Red-AUDIO Right).

Using three yellow VIDEO cables,
connect Y, P

B

, and P

R 

of COMPONENT

VIDEO OUT on the DVD Player to Y, P

B

,

and P

R

 of VIDEO 3 IN on the projection

TV.

• Some DVD Player terminals may be labeled

differently. If so, connect as follows:
Connect Y (green) to Y.
Connect P

B

 (blue) to C

B

, C

b

 or B-Y.

Connect P

R

 (red) to C

R

, C

r

 or R-Y.

– 12 –

HRD

For more dynamic sound, connect an audio system to
the projection TV.

Using an AUDIO cable, connect AUDIO  (VAR/FIX)
OUT on the projection TV to one of the unused Line
inputs (e.g. Tape-2, AUX1, etc.) on the stereo.

Set the stereo to the chosen Line input and use the
Audio menu to set the audio output and switch the
TV’s speakers off.  (see “Salida de audio” and
“Parlantes” on page 22)

Note:
• You can adjust VOLUME, “Graves,” “Agudos,”

“Balance,” “MTS/SAP” and “Efecto” with the
supplied remote control. The control items except
VOLUME can be adjusted only when “Salida de
audio” is set to “Variable” in the Audio menu. (see
“Salida de audio” on page 22)

Use this connection to control the speaker’s Dolby Pro
Logic surround system and super woofer mode with the
remote control. (see “Control SAVA SP ” on page 22)

Using the AUDIO cable supplied with the speaker to
AUDIO (VAR/FIX) OUT on the projection TV.

Using the CONTROL S cable, connect CONTROL S
IN on the speaker to CONTROL S OUT on the
projection TV.

Insert two size AA (R6) batteries (supplied)
by matching the + and – on the batteries to
the diagram inside the remote control’s
battery compartment.

• Remove the batteries to avoid damage

from possible battery leakage whenever
you anticipate that the remote control
will not be used for an extended period.

• Handle the remote control with care.

Avoid dropping it, getting it wet, or
placing it in direct sunlight, near a heater
or where the humidity is high.

• Your remote control can be programmed to

operate most video equipment.
(see “Operating Video Equipment” on
page 30)

• Before you perform AUTO SET UP again,

make sure that the input from ANT (not
AUX) is selected by pressing ANT until
“AUX” does not appear next to the
channel number.

• Perform this function during the day,

with the antenna and/or cable properly
connected, to ensure that all available
channels will be broadcasting and
receivable.

• When you perform AUTO SET UP, all the

settings in the Video, and Audio menus
are reset to the factory settings.

The AUTO SET UP feature will allow you to
set the on-screen language and set all
receivable channels.
The AUTO SET UP feature does not apply for
installations that use a cable box for all channel
selection.