DOWNLOAD Sony KP-43T75C / KP-53SV75C / KP-61SV75C Service Manual ↓ Size: 8.85 MB | Pages: 92 in PDF or view online for FREE

– 25 –

2 Rear board

1 Nine screws (Except KP-43T75C)
     Eight screws (KP-43T75C)
     (Screw(4x20), tapping)

1 Three screws
  (Screw(4x20),tapping)

2 Chassis assy

1 Disconnect CN203 
     on A board.

From CG board CN1304.

(The extension cable is not 
  supplied because of the
  countermeasure for radiation.)

G board

CN203

A board

2 Covers
Cut them off with a plier or the like
from chassis assembly in case of 
checking printed circuit boards.
After checking, turn over the covers 
and secure them with screws.

Screws
(+BVTP3x12)

Chassis assembly      

8 Three screws
   (+BVTP 3x12)

6 Four screws
    (+BVTP 4x12)

2 Two screws
   (+BVTP 4x12)

1 Two screws
    (Screws (4x20), tapping)

9 HB board

7 HB bracket

Speaker grille assy

5 HA board

3 HA bracket

4 Multi button

– 26 –

3 HC board

2 L screen holder

6 Clows

7 S board

Sensor 
bracket (B)

4 Two screws
    (+BVTP 4x12)

1 Two screws
    (+BVTP 4x12)

5 Two screws
    (+BVTP 4x12)

Sensor 
bracket (A)

7 Three screws
   (+BVTP 3x12)

3 Four screws
   (+BVTP 3x12)

5 Three screws
   (+BVTP 3x12)

1 Four screws
    (Screws (4x20), tapping)

8 HB board

Panel ASSY, Control

6 HA board

4 HA bracket

2

1 Three screws 
    (KP-43T75C)
     Five screws 
    (KP-53SV75C/61SV75C)
    (Screws (4x20), tapping)

2 Eleven screws (KP-43T75C)
     Fifteen screws (KP-53SV75C)
     Fourteen screws (KP-61SV75C)
     (Screws (4x20), tapping)

3 Beznet assy

1 Seventeen screws (KP-43T75C) 
     Nineteen screws (KP-53SV75C)
     Twenty three screws (KP-61SV75C)
     (Screw(4x20), tapping)

2 Mirror cover

– 27 –

7 Two screws
    (+BVTP 3x12)

0 Screw
    (+BVTP 3x12)

4 Eight screws
    (+BVTP 3x12)

6 G board

!™ FA board

9 A board

3 Terminal board

8 Claw

5 Claws

Main bracket

!¡ FA board bracket

1 Two screws
    (Screws (4x20), tapping)

2 Seven screws
    (+BVTP 3x12)

4 Four screws
     (Screw(4x20), tapping)

9 Four screws
    (+BVTP 4x12)

0 Picture tube

Picture tube

8 Diflection yoke

2 Four screws
    (Screw(4x20), tapping)

3

1 Four screws
    (Screw(4x20), tapping)

7 Neck assy

6 CR board

5 Lens

Lens

CAUTION: Removing the arrow-marked

screws is strictly prohibited.
If removed, it may cause liquid spill.

(1) Removal

1 Rubber cap

2 HV cable
   turn 90

°

1 HV cable

Gutter

Hook

(2) Installation

– 28 –

1. Receive the Monoscope signal.
2. Set 50% BRIGHTNESS and minimum PICTURE.
3. Turn the red VR on the FOCUS block all the way to the left

and then gradually turn it to the right until the point where you
can see the retrace line.

4. Next gradually turn it to the left to the position where the

retrace line disappears.

R

G

B

SCREEN

R

G

B

FOCUS

FOCUS block

175 

±

 2V

G2 JIG

200V

GND

3.3k

5.6k

5.6k

5.6k

SW

K

GND

pedestal level

Fine Mode is recommended to set screen controls to their optimal
condition.  It is necessary to build the simple jig, illustrated below,
using 3-watt resistors.  Please note, that if the proper voltage is not
obtained with their listed values, resistors, then please increase or
decrease one of the values in the resistor network to obtain the
correct voltage.
1. Select VIDEO1 mode without signals.
2. Connect G2 JIG.
3. SW on JIG.
4. Connect an oscilloscope to the TP701(KR), TP732(KG) and

TP761(KB) of CR board, CG board and CB board.

5. Adjust  R, G and B screen voltage to 168-172V with screen

VR on the Focus block.

In this adjustment, use the remote commander in the
service mode.
For details of the usage of the service mode and the remote
commander, please refer the item 3-9. ELECTRICAL
ADJUSTMENT BY REMOTE COMMANDER.

1. Loosen the lens screw.
2. Set to the service mode.
3. Receive the all-white signal.
4. Cover the both red and blue picture lenses with the lens caps

to show only the green color.

5. Set to PJE, and press 6 to display the test signal (crosshatch)“

on the screen.

6. Turn the green lens to adjust to the optimum focus point with

the test signal.

7. Tighten the lens screw.
8. Cover the both green and blue picture lenses with the lens caps

to show only the red color.

9. Set to PJE, and press 6 to display the test signal (crosshatch)“

on the screen.

10. Adjust red CRT lens just the same as green.
11. Cover the both green and red picture lenses with the lens caps

to show only the blue color.

12. Set to PJE, and press 6 to display the test signal (crosshatch)“

on the screen.

13. Adjust blue CRT lens just the same as green.
14. After adjusting the items 3-5. Focus VR Adjustment, 3-6. 2-

Pole Magnet Adjustment and 3-7. 4-Pole Magnet Adjustment,
adjust again to the optimum focus point.

*: Every time you press 6, the test signal changes to

“crosshatch+video signal” - “dots+video signal” -
“crosshach(black)” - “dots(black)” - off.

Note: Instead of items 4, 8 and 11, you can cut off the unnecessary

color beams by controlling the service mode VPNT 28 RON,
29 GON, and 30 BON.

Test signal

1. Receive the Monoscope signal.
2. Set in service mode.
3. Cover the both red and blue picture lenses with the lens caps

to show only the green color.

4. Loosen the deflection yoke set screw and align the tilt of the

Deflection Yoke so that the bars at the center of the
monoscope pattern are horizontal.

5. After aligning the deflection yoke, fasten it securely to the

funnel-shaped portion (neck) of the CRT.

6. The tilt of the deflection yoke for red is aligned  in the mode

Cover the both green and blue picture lenses with the lens caps
and the tilt of the deflection yoke for blue is aligned with in

2-pole magnet

4-pole magnet

Deflection yoke

Anode cap

the mode Cover the both green and red picture lenses with the
lens caps is aligned the same as was done for green.

Note: Instead of items 3 and 6, you can cut off the unnecessary

color beams by controlling the service mode VPNT 28 RON,
29 GON, and 30 BON.