DOWNLOAD Sony KP-43HT20C / KP-53HS30C Service Manual ↓ Size: 9.55 MB | Pages: 127 in PDF or view online for FREE

– 10 –

1

   B board

1

   AD board

Main bracket

4

   G board

2

   Bracket G

1

   Claws

1

   Claw

1

   Claw

Main bracket

3

   Four screws

    (+BVTP3x12)

3

   H4 board

2

   L screen holder

6

 Clows

7

 S board

Sensor 
bracket (B)

4  

 Two screws

     (+BVTP 4x12)

1

   Four screws

     (+BVTP 4x12)

5

   Two screws

     (+BVTP 4x12)

Sensor 
bracket (A)

1

   Screws 

     (Screws(4x20), tapping)

2

   Screws 

     (Screws(4x20), tapping)

3

   Beznet assy

– 11 –

(1) Removal

1

   Rubber cap

2

   HV cable

     turn 90¡

1

   HV cable

Gutter

Hook

(2) Installation

4

   Four screws

     (Screw (4x20), tapping)

8

   Two screws (+BVTP3

12  Four screws (+BVTP 4x12)

13  Picture tube

Picture tube

10  Deflection yoke

2

   Four screws

  (Screw (4x20),
      tapping)

3

1  

 Four screws

    (Screw (4x20), tapping)

7

   Neck assy

6  

 CR board

9

   V board

5

   Lens

Lens

CAUTION:    Removing the arrow-marked
                     screws is strictly prohibited.
                     If removed, it may cause liquid spill.

6

   D board

6

   A board

2

   Terminal board

5

   Claws

Main bracket

3

   U board

1

   Two screws

    (+BVTP3x12)

4

   Screws

    (+BVTP3x12)

4

   Six screws

    (+BVTP3x12)

1  

 Five screws

    (+BVTP3x12)

– 12 –

2-pole magnet

4-pole magnet

Deflection yoke

Anode cap

Centering magnet

1.   Receive the Monoscope signal.
2.   Set 50% BRIGHTNESS and minimum PICTURE.
3.   Turn the red VR on the FOCUS block all the way to the left 

and then gradually turn it to the right until the point where you 
can see the retrace line.

4.   Next gradually turn it to the left to the position where the 

retrace line disappears.

R

G

B

SCREEN

R

G

B

FOCUS

FOCUS block

170 ± 0.5V

G2 JIG

TO CG BOARD

TP7201

(200V)

GND

3k

5.6k

5.6k

5.6k

SW

K

GND

pedestal level

All resistors are 3W type

Fine Mode is recommended to set screen controls to their optimal 
condition.  It is necessary to build the simple jig, illustrated below, 
using 3-watt resistors.  Please note, that if the proper voltage is 
not obtained with their listed values, resistors, then please increase 
or decrease one of the values in the resistor network to obtain the 
correct voltage.
1.   Select VIDEO1 mode without signals.
2.   Connect G2 JIG.
3.   SW on JIG.
4.   Connect an oscilloscope to the TP7101(KR), TP7202(KG) and 

TP7301(KB) of CR board, CG board and CB board.

5.   Adjust  R, G and B screen voltage to 170 ± 0.5V with screen 

VR on the Focus block.

1.   Connect the color bar generator monoscope pattern to Video 

1 input.

2.   Cover the both red and blue picture lenses with the lens caps to 

show only the green color.

3.   Loosen the defl ection yoke set screw and align the tilt of the 

Defl ection Yoke so that the bars at the center of the monoscope 
pattern are horizontal.

4.   After aligning the defl ection yoke, fasten it securely to the 

funnel-shaped portion (neck) of the CRT.

In this adjustment, use the remote commander in the service 
mode.
For details of the usage of the service mode and the 
remote commander, please refer the item 3-9. ELECTRICAL 
ADJUSTMENT BY REMOTE COMMANDER.

1.   Loosen the lens screw.
2.   Cover the both red and blue picture lenses with the lens caps to 

show only the green color.

3.   Turn the green lens to adjust to the optimum focus point with 

the crosshatch signal.

4.   Tighten the lens screw.
5.   Cover the both green and blue picture lenses with the lens caps 

to show only the red color.

6.   Adjust red CRT lens just the same as green.
7.   Cover the both green and red picture lenses with the lens caps 

to show only the blue color.

8. Adjust blue CRT lens just the same as green.
9. After adjusting the items 3-5. Focus VR Adjustment, 3-6. 

2-Pole Magnet Adjustment and 3-7. 4-Pole Magnet Adjust-
ment, adjust again to the optimum focus point.

*:  Every time you press 6, the test signal changes to 

“crosshatch+video signal” - “crossbatch+borderline(black)” 
- “crosshach(black)” - “dots(black)” - off.

Note: Instead of items 2, 5 and 7, you can cut off the unnecessary 

color beams by controlling the service mode CXA2150P-2 0 
RGBS.

Test signal

5.   The tilt of the defl ection yoke for red is aligned  in the mode 

Cover the both green and blue picture lenses with the lens caps 
and the tilt of the defl ection yoke for blue is aligned with in the 
mode Cover the both green and red picture lenses with the lens 
caps is aligned the same as was done for green.

Note: Instead of items 2 and 5, you can cut off the unnecessary 

color beams by controlling the service mode CXA2150P-2 0 
RGBS.

– 13 –

1.   Set the picture mode to “Pro”.
2.   Receive the monoscope signal.
3.   Cover the both red and blue picture lenses with the lens caps to 

show only the green color.

4.   Adjust the green centering magnet to put the center of the 

monoscope signal to the center of the screen.

5.   Adjust the red centering magnet in the same way.
6.   Adjust the blue centering magnet in the same way.
Note: Instead of item 2 you can cut off the unnecessary color 

beams by controlling the service mode 2150P-2 1 RGBS.

1.   Set the picture mode to“Pro” and picture to MAX.
2.   Receive the Dot signal.
3.   Cover the both red and blue picture lenses with the lens caps to 

show only the green color.

4.   Turn the green focus VR on the focus block to the right and set 

the spot will become smaller.

5.   Adjust the 4-Pole Magnet so that the spot becomes round for 

green and red.

6.   Adjust blue spot to an oval shape X:Y=1:1.4 ~ 1.5.
Note: Instead of item 2 you can cut off the unnecessary color 

beams by controlling the service mode 2150P-2 1 RGBS.

Note: Please adjust the blue dot to be slightly larger than red and 

green dots. This adjustment provides a more pleasing picture 
to the customer.

1.   Select the picture mode to “Pro”.
2.   Receive the Dot signal.
3.   Cover the both red md green picture lenses with the lens caps 

to show only the blue color.

4.   Turn the blue focus VR on the focus block to right to make 

the round dot elipical.

5.  Check fl are with high luminace signal, make sure fl are is 

minimal while dot shape is elipical.

6.   Set generdtor to all white signal and check uniformity.
Note: Instead of item 3 you can cut off the unnecessary color 

beams by controlling the service mode 2150P-2 1 RGBS.

/

x

y

x : y = 1:1.4 

˜

 1.5 (BIue)

x : y = 1:1 (Green, Red)

Use the center dot

1.   Set generator to crosshatch.
2.   Cover the both red and blue picture lenses with the lens caps to 

show only the green color.

3.   Turn the green focus VR on the focus block to adjust to the 

optimum focus point with the crosshatch signal.

4.   Cover the both green and blue picture lenses with the lens caps 

to show only the red color.

5.   Turn the red focus VR on the focus block to adjust to the 

optimum focus point with the crosshatch signal.

6.   Cover the both green and red picture lenses with the lens caps 

to show only the blue color.

7.   Turn the blue focus VR on the focus block to adjust to the 

optimum focus point with the crosshatch signal.

8.   After adjusting the items 3-4. Focus Lens Adjustment, 3-6. 

2-Pole Magnet Adjustment and 3-7. 4-Pole Magnet Adjust-
ment, adjust again to the optimum focus point.

Note: Instead of items 2, 4 and 6, you can cut off the unnecessary 

color beams by controlling the service mode 2150P-2 1 RGBS.

A

B

Lens

Minimize both A and B.

Center of crosshatch

Scanning line visible.

1.   Set the picture mode to“Pro” and picture to MAX.
2.   Receive the Dot signal.
3.   Cover the both red and blue picture lenses with the lens caps to 

show only the green color.

4.   Turn the green focus VR on the focus block to the left and set 

to overfocus to enlarge the spot.

5.   Adjust 2-pole magnet so that the bright spot should be cen-

tered.

6.   Align the green focus VR and set for just (precise) focus.
7.   Perform the same alignment for red and blue.
Note: Instead of item 2 you can cut off the unnecessary color 

beams by controlling the service mode 2150P-2 1 RGBS.