Sony KP-43HT20C / KP-53HS30C Service Manual ▷ View online
– 26 –
KP-43HT20C/53HS30C
RM-Y908
RM-Y908
2. Operation Method for Coarse Adjustment
1) Enter the Service mode, and select “PJE”.
2) Press “
#
” or “
$
” button on the commander to select the
item, and use the joystick to change the data.
3) Select “GRN CENT” . When BLU or RED is displayed, press
“
%
” button on the commander to change the adjustment
color in the order of GRN ! BLU ! RED.
4) In the GRN, BLU, or RED mode,move
!"
direction
the joystick can change the data in vertical direction, or
#$
direction in horizontal direction.
5) Before returning to the Service mode, press “MUTING”
+“ENTER” buttons on the commander to write the data.
(Omission of this operation causes the set data to be returned
to the data before adjustment)
PJE 00 00
FDIS
FDIS
Adjustment Item
Item No.
Data
!$
direction:Data up
"#
direction:Data down
GRN 000 000
CENT
CENT
Adjustment Item
Data (H)
Data (V)
Color
#
:Data (H) up
$
:Data (H) down
!
:Data (V) up
"
:Data (V) down
Joystick
3-11-3. Operation Method for Projector Engine
Mode
1. Functions of Keys on Commander
•
#
: Changes adjustment item. (item No. moves up)
: Marker moves clockwise from center to outside.
(in fi ne adjustment mode)
•
$
: Changes adjustment item.
(item No. moves down)
: Marker moves counterclockwise from outside
to center. (in fi ne adjustment mode)
•
&
: Changes adjustment category.
(category No. moves up)
•
'
: Changes adjustment category.
(category No. moves down)
• Joystick : Changes data value. (up or down)
: Marker moves up, down, or to the left or right.
(in fi ne adjustment mode)
•
%
: Changes adjustment color.
GRN ! BLU ! RED
•
(
: Displays or changes internal test signals.
: crosshatch + external signal ! crosshatch
+borderline ! crosshatch only ! dot only !
off
•
)
: Switches adjustment mode.
Coarse adjustment mode ! fine adjustment
mode
Color change
Internal test signal
Mode select
(Fine or Coarse)
(Fine or Coarse)
Adjustment item
up
up
Adjustment item
down
down
Category up
Category down
RM-Y908
TV POWER
VOLUME +
DISPLAY
Initialize data
(Not stored)
(Not stored)
data up/down
MUTING
ENTER
MENU
• Press joy : Switches marker moving method.
stick (in fi ne adjustment mode)
joystick (
!"#$
) keys !
#
and
$
buttons
Commander Function
Buttons
Mode
Description
- + ENTER
READ
Writes data to NVM.
MUTING+ENTER
WRITE
Reads data from NVM.
7 + ENTER
PJE
Service data initialization. Not stored.
INITIAL
(Be sure not to use usually)
– 27 –
KP-43HT20C/53HS30C
RM-Y908
RM-Y908
3-11-4. PJE Adjustment
(Sub Defl ection Adjustment)
(Sub Defl ection Adjustment)
Push the joystick
to
Push the joystick
to
Push the joystick
to
Push the joystick
to
• GRN CENT (horizontally/vertically)
<Adjustment for NTSC Full Mode>
• The adjustment should be done in the numerical order
given.
1. Green Adjustment
1) Place the caps on the red and blue lenses so that only the
green color is displayed.
2) Enter the monoscope signal to set.
3) Select the PJE mode.
4) Press “
(
” button on the commander to display internal test
signal (crosshatch).
5) Select “GRN CENT”, and adjust so that the picture coincide
in the center of screen.
3. Operation Method for Fine Adjustment
1) Select the PJE mode.
2) Select FDIS so that the data at each position can be displayed
in the fi ne adjustment mode, and set the data to “01”.
3) Press “
)
” button on the commander, and the fi ne adjustment
mode will be active where a green marker appears in the
center of screen (in the case of GRN mode).
4) Press joystick, and the marker color will be switched between
green (GRN mode) and white alternately.
5) Use “
#
” or “
$
” button on the commander, or the joystick
to move the marker to the position to be adjusted, where fi ne
adjustment can be made.
• When marker color is white.
(in this case, fi ne adjustment is disabled)
Operating the joystick can move the marker
up, down, or to the left or right freely.
• When marker color is green. (GRN mode)
#
: moves the marker clockwise from center to outside.
$
: moves the marker counterclockwise from outside to
center.
• Fine adjustment can be made on the basis of marker
position using
!"#$
directiom of the joystick.
6) Press “
)
” button on the commander to return to the coarse
adjustment mode.
CROSSHATCH
Move joystick
direction
Move joystick
direction
CROSSHATCH
Note: If the value of over the limit value, adjust these in the fi ne
adjustment .
Coarse Data Limit Valune.
Cent H 35±170 V 20±170, Size H-75max, Lin H Blu
-425min, H Red 425max.
adjustment .
Coarse Data Limit Valune.
Cent H 35±170 V 20±170, Size H-75max, Lin H Blu
-425min, H Red 425max.
Adjustment Type
Adjustment Item
GRN
RED
BLU
H / V
H / V
H / V
CENT
a / a
a / a
a / a
SKEW
a / a
a / a
a / a
SIZE
a / a
a / a
a / a
LIN
a / a
a / a
a / a
KEY
– /
a
– /
a
– /
a
PIN
a / a
a / a
a / a
MLIN
a / –
a / –
a / –
MSIZ
a / –
a / –
a / –
Adjustment
a : Yes
– : No
– 28 –
KP-43HT20C/53HS30C
RM-Y908
RM-Y908
• GRN MLIN (horizontally)
11) Select “GRN MLIN”, and correct the sizes of the horizontal
line at the center of the screen are symmetrical left and
10) Select “GRN MSIZ”, and correct the space intervals for the
horizontal section of the screen are equal.
• GRN MSIZ (horizontally)
Push the joystick
to
Push the joystick
to
Push the joystick
to
Push the joystick
to
7) Select “GRN SKEW”, and correct the tilt of horizontal lines
and vertical lines.
8) Select “GRN SIZE”, and adjust so that each distance from
center to left end and to right end is equal. Adjust so that each
distance from center to top and to bottom is equal.
• GRN SIZE (horizontally/vertically)
9) Select “GRN LIN”, and adjust so that each space at the right
end and at the left end of screen is equal. Adjust so that each
space at the top and at the bottom of screen is equal.
• GRN LIN (horizontally/vertically)
Push the joystick
to
Push the joystick
to
Push the joystick
to
Push the joystick
to
Push the joystick
to
Push the joystick
to
Push the joystick
to
Push the joystick
to
Push the joystick
to
Push the joystick
to
Push the joystick
to
Push the joystick
to
Note: The SIZE and LIN, MSIZ and MLIN adjustments are
affected each other.
So adjust these mutually if necessary.
affected each other.
So adjust these mutually if necessary.
Push the joystick
to
Push the joystick
to
Push the joystick
to
Push the joystick
to
12) Select “GRN PIN”, and adjust so that right and left vertical
lines on the screen become straight. Adjust so that upper and
lower horizontal lines on the screen become straight.
• GRN PIN (horizontally/vertically)
13) Select “GRN KEY”, and adjust so that upper and lower
horizontal lines on the screen become parallel.
• GRN KEY (vertically)
Push the joystick
to
Push the joystick
to
Note: The VPINand KEY adjustments are affected each other.
So adjust these mutually if necessary.
So adjust these mutually if necessary.
• GRN SKEW (horizontally/vertically)
– 29 –
KP-43HT20C/53HS30C
RM-Y908
RM-Y908
2. Red Adjustment
1) Place a cap on the blue lens so that green and red colors
are displayed.
2) Press “
%
” button on the commander to select RED mode.
3) Adjust the following items so that red lines overlap with
green lines.
• RED CENT (horizontally/vertically)
• RED SKEW (horizontally/vertically)
• RED SIZE (horizontally/vertically)
• RED LIN (horizontally/vertically)
• RED MSIZ (horizontally)
• RED MLIN (horizontally)
• RED PIN (horizontally/vertically)
• RED KEY (vertically)
4) Press “
)
” button on the commander to enter the fine
adjustment mode.
5) Make fi ne adjustment so that horizontal lines and vertical
lines overlap with green lines.
6) Press “
)
” button on the commander to return to the coarse
adjustment mode.
3. Blue Adjustment
1) All colors are displayed.
2) Press “
%
” button on the commander to select BLU mode.
3) Hereinafter, use same manner as that of red adjustment to
adjust so that the blue lines overlap with green and red lines.
4. Registration Data Writing
1) After each adjustment of green, blue, and red for the NTSC
Full mode fi nished, press “MUTING”+ “ENTER” buttons on
the commander to write registration data to the NVM.
14) Press “
)
” button on the commander to enter the fine
adjustment mode.
15) Make fi ne adjustment so that horizontal lines and vertical
lines become straight.
16) Press “
)
” button on the commander to return to the coarse
adjustment mode.
Full
Screem
mode
Zoom
Screen
mode
Wide Zoom
Screen
mode
HD
(1080i Full
Screen mode)
Copy Registration Data.
<Copy All Registration Data to Other modes>
1. Make sure that the adjustment for NTSC Full mode fi nished
and the data have already been written.
2. Select the PJE mode.
3.
Select ALCP and set the data to “01”, and press
“MUTING”+“ENTER” buttons on the commander.
4. The data of NTSC Full mode are copied to all other modes.
5. Check in the other mode and adjust as the occasion demands.
Be sure to write data in each mode.
3-12. AUTO CONVERGENCE OFFSET
This adjustment must be performed after the registration adjustment
was made or after readjustment was made by any reason.
1. Darken the periphery of this set.
2. Enter the monoscope signal to set the NTSC Full mode.
3. Select the PJE mode.
4. Press “FLASH FOCUS” button on the front panel of the set.
(The offset value is now automatically stored)
5. Select “ ERR” of PJE mode.
Confirm ERR is “00”. If ERR is not “00”, recheck. (Refer
to 3-12.)
6. Exit the service mode.
3-13. AUTO REGISTRATION ERROR CODE LIST
If an error code is displayed after the set has been fully adjusted,
correctly, plese check the following items : position, tilt and sizing. If
either of these adjustments are off, even slightli, the auto registration
pattern will not hit the four sensors properly. This occurs when the
internal generator patterns is being fl ashed on the screen for the sensor
to read. Therefore, auto registration (called auto convergence) cannot
operate properly causing an error code to be displayed. In order for
this function to operate properly, correct position, tilt and size must
be adjusted properly.
Click on the first or last page to see other KP-43HT20C / KP-53HS30C service manuals if exist.