DOWNLOAD Sony KLV-46XBR9 / KLV-52XBR9 Service Manual ↓ Size: 16.97 MB | Pages: 88 in PDF or view online for FREE

After correcting the original service problem, perform the following 
safety checks before releasing the set to the customer:

1.  Check the area of your repair for unsoldered or poorly soldered 

connections. Check the entire board surface for solder splashes and 
bridges.

2.  Check the interboard wiring to ensure that no wires are “pinched” or 

touching high-wattage resistors.

3.  Check that all control knobs, shields, covers, ground straps, and 

mounting hardware have been replaced. Be absolutely certain that 
you have replaced all the insulators.

4.  Look for unauthorized replacement parts, particularly transistors, 

that were installed during a previous repair. Point them out to the 
customer and recommend their replacement.

5.  Look for parts which, though functioning, show obvious signs of 

deterioration. Point them out to the customer and recommend their 
replacement.

6.  Check the line cords for cracks and abrasion. Recommend the 

replacement of any such line cord to the customer.

7.  Check the antenna terminals, metal trim, “metallized” knobs, screws, 

and all other exposed metal parts for AC leakage. Check leakage as 
described below.

The AC leakage from any exposed metal part to earth ground and 
from all exposed metal parts to any exposed metal part having a 
return to chassis, must not exceed 0.5 mA (500 microamperes). 
Leakage current can be measured by any one of three methods.

1.  A commercial leakage tester, such as the Simpson 229 or RCA 

WT-540A. Follow the manufacturers’ instructions to use these 
instructions.

2.  A battery-operated AC milliampmeter. The Data Precision 245 

digital multimeter is suitable for this job.

3.  Measuring the voltage drop across a resistor by means of a VOM 

or battery-operated AC voltmeter. The “limit” indication is 0.75 
V, so analog meters must have an accurate low voltage scale. 
The Simpson’s 250 and Sanwa SH-63TRD are examples of 
passive VOMs that are suitable. Nearly all battery-operated digital 
multimeters that have a 2 VAC range are suitable (see Figure A).

How to Find a Good Earth Ground
A cold-water pipe is a guaranteed earth ground; the cover-plate 
retaining screw on most AC outlet boxes is also at earth ground. If the 
retaining screw is to be used as your earth ground, verify that it is at 
ground by measuring the resistance between it and a cold-water pipe 
with an ohmmeter. The reading should be zero ohms.

If a cold-water pipe is not accessible, connect a 60- to 100-watt 
trouble- light (not a neon lamp) between the hot side of the receptacle 
and the retaining screw. Try both slots, if necessary, to locate the hot 
side on the line; the lamp should light at normal brilliance if the screw 
is at ground potential (see Figure B).

Trouble Light

AC Outlet Box

Ohmmeter

Cold-water Pipe

Figure A. Using an AC voltmeter to check AC leakage.

Figure B. Checking for earth ground.

The units in this manual contain a self-diagnostic function. If an error occurs, the POWER/STANDBY LED indicator will automatically begin to fl ash. 
The number of times the LED fl ashes translates to a probable source of the problem. A defi nition of the POWER/STANDBY LED fl ash indicators is 
listed in the instruction manual for the user’s knowledge and reference. If an error symptom cannot be reproduced, the Remote Commander can be 
used to review the failure occurrence data stored in memory to reveal past problems and how often these problems occur.

When an error occurs, the POWER/STANDBY LED indicator will fl ash a set number of times to indicate the possible cause of the problem. If there is 
more than one error, the indicator will identify the fi rst of the problem areas.

Orange or Green

Lights up in orange when the Timer or Sleep is set.
Lights up in green when the Power Saving is set to 
Picture Off.

Red

Lights up in red when your TV is in PC power saving 
mode.

Green or Red

Lights up in green when the TV is turned on. If the LED 
blinks in red continuously, this may indicate that the TV 
needs servicing.

Main Power

 2 times

G7N (Power) Board

DC Alert1

3 times

BR Board
G7N (Power) Board

DC Alert3

5 times

Not used in these models

Backlight

6 times

BR Board
G7N (Power) Board
Inverter Boards -D1N Board & D2N Board (46"), D3N Board & D4N Board (52")

Temp Err

7 times

BR Board

Audio Prot

8 times

BR Board

Fan Err

9 times

Not used in these models

DTT WDT

10 times

Watch Dog Timer used to track micro processors, not to record errors.

Trident IC

11 times

BR Board

HFR Err

12 times

LCD Panel

Balancer

13 times

LCD Panel
Inverter Boards -D1N Board & D2N Board (46"), D3N Board & D4N Board (52")

TCON Err

14 times

LCD Panel

1.  TV must be in standby mode. (Power off).

2.  Press the following buttons on the Remote Commander within a second of each other: 

 

DISPLAY   

Channel 

5   

Volume 

-  

  TV POWER .

 

The Self Check list displays. 

          

  This differs from accessing Service Adjustments.

Results for all of the following diagnostic items are displayed on screen.  No error has occurred if the screen displays a “0”.

 

DIAGNOSTICS  

 

002  MAIN POWER   

 

001

003  DC ALERT 1 

 

 

000

005  DC ALERT3 

 

 

000

012  HFR ERR 

 

 

000

006  BACKLIGHT 

 

 

000

007  TEMP ERR 

 

 

000

008  AUDIO PROT   

 

000

009  FAN ERR 

 

 

000

010  DTT WDT 

 

 

000

012  HFR_ERR 

 

 

000

013  BALANCER 

 

 

000

014  TCON_ERR 

 

 

000

00000-00000-00000

SELF CHECK

3.  To exit Self Check display, turn the power off.

Clearing the Self Check Diagnostic List
1.  In Service Mode, press the Channel  8   

Channel 

0 .

Clearing the Panel Operation Time
1.  In Service Mode, press the Channel  7   

Channel 

0 .

1   Remove 8 screws from Rear Cover 

2   Remove 1 screw from Side Jack position

3   Remove 1 screw from Terminal position

4   Remove 4 screws from VESA positions

5   Remove 3 screws from Bottom Frame positions

6   Carefully lift Rear Cover bottom side and rotate toward top side

7   Release Clamps and remove Rear Cover from Front Cabinet Assembly

NOTE: 

The Rear Cover is attached to Front Cabinet Assembly with small Clamps (3 places).

 

  

Use caution when removing the Rear Cover not to damage these Clamps.

 

  

To re-install the Rear Cover, press the Rear Cover down on Clamps to lock into position.

6

7

Clamps

Front Cabinet Assembly

Rear Cover

Front Cabinet Assembly

Rear Cover

1 Screw,

+BVTP2 4X16

2 Screw, 

+BVTP 3X12 TYPE2 IT-3

3 Screw, 

+BVTP 3X12 TYPE2 IT-3

4 Screw, 

+PSW M5X12 

5 Screw, 

+PSW M5X12