DOWNLOAD Sony KLV-22T550A / KLV-32T550A Service Manual ↓ Size: 2.85 MB | Pages: 36 in PDF or view online for FREE

– 16 –

i) Non-CISPR model

ii) CISPR model

P4

P3

P5

P4

P3

P5

1) Insert SP Conn Assy 4P to speakers as shown.
2) Attach LCD, Tape to speaker and panel as shown. (X3)
3) Insert Connector Assy 14P to inverter as in the picture

For SLCD panel only
1) Tape Sheet Core, C to fix the LVDS position as shown
2) Separate Spk Conn Assy 4P, Conn Assy 14P & LVDS when dress together at spine frame(X2)
3) Insert the Lead Assy Earth to power board. Do not tape LCD, Tape on the power board.
For AUO panel
1) Separate Spk Conn Assy 4P, Conn Assy 14P & LVDS when dress together at spine frame(X2)
2) Insert the Lead Assy Earth to power board. Do not tape LCD, Tape on the power board.

Do not tape on

the speaker hole

Right

speaker

AUO

panel

Right

speaker

 

Conn Assy 14P

Spk Conn Assy 4P

Insert Spk Conn Assy

4P to speaker.

Attach LCD, Tape. (X3)

 

Insert SP Conn

Assy 4P to

speakers

Right speaker

SLCD panel

Insert Spk Conn

Assy 4P to speaker.

Attach LCD, Tape.

(X3)

Conn Assy 14P

Spk Conn Assy 4P

Insert SP Conn Assy 4P

to speakers

 

AUO panel

Attach Sheet Core, 

C to panel & Frame 
Spine as hown (X3).

 

Attach Sheet Core, C to

panel & Frame Spine as 

shown (X3).

Do not dress Spk Conn 

Assy 4P, Conn Assy 14P 

& LVDS together

SLCD panel

GT3

GT3

Insert the Lead Assy Earth. 

Attach LCD, Tape to bottom 

bracket as shown (X1).

When inserting LVDS harness to panel, make sure it is fully inserted

and in the correct direction

SLCD panel

AUO  panel

AUO panel

 LVDS

 LVDS

Do not dress Spk Conn

Assy 4P, Conn Assy 14P 

& LVDS together

1

2

3

1

2

3

1

2

1

2

3

– 17 –

1) Insert Connector Assy 10P to HT3
2) Attach Sheet Core, C (X1) to main bracket as shown.

Dress Lead Assy Earth & Conn

Assy 10P together. Attach

Sheet Core, C (x1)

HT3

BT2

Lead Assy Earth conn

Conn Assy

Do not over pull the

Conn Assy 10P

Do not dress

Spk Conn Assy

4P in this area

Conn Assy 10P

LVDS

Spk Conn

Assy 4P

1) Insert Spk Conn Assy 4P to speaker
 

Attach LCD, Tape to Spk Conn Assy 4P

 

on the speaker.

Note: Do not tape on the speaker hole

Insert Spk Conn Assy 4P

to speaker.

Attach LCD, Tape.

Left speaker

Do not tape on the

speaker hole

1) Install AC cord holder to AC power cord at the position shown
2) Insert AC power cord to GT3 PWB
3) Install AC cord holder into the under cover
4) Dress AC power cord using pin wire , A6101
5) Keep the distance >4mm away from the surrounding parts.

Keep

>4mm

Insert Ac Power

Cord

 

3

Dress AC power

cord using pin wire

Clamp AC Cord Holder to AC

Power Cord at this position

Make sure distance of .4mm is kept from

F6102 and C6111 lead to single insulated

portion of AC power cord (Blue and Brown

wire). This can be controlled by using pin, wire

A6101 to dress AC power cord away from

conductive parts.

1

2

1

2

5

4

– 18 –

1.

While TV set on standby, press the following sequence on
the Remote commander (RMGA016).

The following menu will appear on the screen

2.

To quit the diagnostic menu, turn off and on the set.

1.

While TV on standby mode, press the following sequence
on the Remote commander.

(if wrong key is pressed or passed 3 seconds during each
process, cancel entering the self-diagnosis display.)

Example on screen display:

2.

To reset, press 8 – 0 –     .

3.

To Exit, press the <I/

1

> key .

Figure 1

On screen

display

Channel 5

Volume (-)

POWER

MAIN_POWER_ERROR

5V_POWER_ERROR

AUDIO_ERROR

BALK_LIGHT_ERROR

 TEMP_ERROR

0

0

0

0

0

Buttons on the Remote Commander to access the service
menu items and adjust the data values.

1.

While TV on standby mode, press the following sequence
on the Remote commander.

2.

Select AGING with 

2

 or 

5

 On the Remote Commander.

3.

Select AGING MODE with 

1

 or 

4

 On the Remote

Commander.

4.

Select data value with 

3

 or 

6

 On the Remote

Commander to 1 to enable. Refer to Service Items
(Table 1) page 20.

5.

Press <I/

1

> to exit.

6.

When exit it will have the new data value and start aging.

7.

Aging condition:

a) Supply voltage : Rating
b) Time: More than 20 minutes
c) Ambient Temp: 22-28 degrees
d) Input : Set no signal except digital and analog
    RF(Video/Component/PC)

Example on screen display:

On screen

display

Channel 5 

Volume (+)

POWER

On screen

display

Channel 5 

Volume (+)

POWER

Remote Button

Function

[1]

 / 

[4]

Item up / down

[2]

 / 

[5]

Category up / down

[3]

 / 

[6]

Data up  / down

[3]

 

/

 

[7]

Initialize data

[3]

 / 

[8]

Test Reset

[3]

 /

 

[10]

 / 

[0]

Execute Data

 

Change Mode 

<JUMP>

Note
All data have been set for optical viewing for customers.
This section serves for informational purpose only.

[Category/Item name] Within 17 characters

[Data] Within 7 characters

LOCTOP
  PROGRAM: Show the Application version
  GTV: Show the GTV Library version
  NVM: Show the NVM version in the NVM data
  (4bytes ASCII data)
  MODEL ID: Show the MODEL ID in the NVM 
data
USB
  PROGRAM: Show the USB update micro 

CATEGORY

ITEM

LOCTOP
  PROGRAM: Show the Application version
  GTV: Show the GTV Library version
  NVM: Show the NVM version in the NVM data
  (4bytes ASCII data)
  MODEL ID: Show the MODEL ID in the NVM 
data
USB
  PROGRAM: Show the USB update micro 

– 19 –

1.

While TV on standby mode, press the following sequence
on the Remote commander.

2.

Select SERVICE with 

2

 or 

5

 On the Remote

Commander.

3.

Select AUTO SET FACTORY with 

1

 or 

4

 On the Remote

Commander.

4.

Select data value with 

3

 or 

6

 On the Remote

Commander to 0 current condition. Refer to
Service Items (Table 1) page 20.

5.

Press <I/

1

> to exit.

On screen

display

Channel 5 

Volume (+)

POWER

Example on screen display:

Test Pattern:
a) Connect video signal of white to video input
b) Restort to original value : Color temp=0,
Picture=Max,Brightness=50,Backlight=max

1.

While TV on standby mode, press the following sequence
on the Remote commander.

2.

Select WB with 

2

 or 

5

 On the Remote Commander.

3.

Select WPR_C with 

1

 or 

4

 On the Remote Commander.

4.

Select data value with 

3

 or 

6

 On the Remote

Commander.

5.

Press <I/

1

> to exit.

Note: Refer to Service Items (Table 1) page 20 for other item
and data value.

On screen

display

Channel 5 

Volume (+)

POWER

Example on screen display:

LOCTOP
  PROGRAM: Show the Application version
  GTV: Show the GTV Library version
  NVM: Show the NVM version in the NVM data
  (4bytes ASCII data)
  MODEL ID: Show the MODEL ID in the NVM 
data
USB
  PROGRAM: Show the USB update micro 

LOCTOP
  PROGRAM: Show the Application version
  GTV: Show the GTV Library version
  NVM: Show the NVM version in the NVM data
  (4bytes ASCII data)
  MODEL ID: Show the MODEL ID in the NVM 
data
USB
  PROGRAM: Show the USB update micro