Sony KE-37XS910 / KE-42XS910 / KE-MX37A1 / KE-MX37N1 / KE-MX37S1 Service Manual ▷ View online
– 29 –
4.3 CHECKING THE PRODUCT REQUESTED FOR REPAIR
Check the serial ID number of the product requested for repair before starting the problem
analysis and repair.
analysis and repair.
Structure of serial ID number is shown below.
(1) Checking serial ID number of PDP module (14 digits)
The serial ID number of the product that is brought in for service and that of the
completed panel chassis has the structure as shown below.
completed panel chassis has the structure as shown below.
The serial ID number is shown on the bar code label that is attached to the rear of the
chassis (aluminum).
chassis (aluminum).
N7A 1 01 001A1 01A
Version No.: 01 ~ 99
A ~ Z (excluding I and O)
A ~ Z (excluding I and O)
Lot No.: 001 ~ 999
A ~ Z (excluding I and O)
1 ~ 3
A ~ Z (excluding I and O)
1 ~ 3
Production week code: 01 ~ 53
Production year (low digit): 0 ~ 9
Product code: N7A- model 42 type
Module product label Serial ID label of panel chassis
* The module serial ID number and the serial ID number of the completed chassis (product
requested for repair) are usually the same when the product is brought in for repair for the first
time.
time.
– 30 –
(2) Checking serial ID number of constituent PC boards (12 digits)
The serial ID number of the module constituent PC boards has the following structure.
The serial ID number is shown on the bar code label that is attached to each PC board.
Cs 1 01 00001 1A
Version No.: 1 ~ 9 , a~z
A ~ Z (excluding I and O)
A ~ Z (excluding I and O)
Lot No.: 00001 ~ Z9999
Production week code: 01 ~ 53
Production year (low digit): 0 ~ 9
Product code:
– 31 –
4.4 OPERATION TEST PROCEDURE
Check Fault Symptom
(1) Prepare the test equipment and the module requested for repair.
(2) Affix to the stand (jig) the module requested for repair.
(3) Connect LOGIC board connector CN1 of the module to the Interface
board (jig)CN5 with the dedicated signal cable.
(5) Turn on the AC power to the interface board (jig).
(7) Set the PDP go switch on the Interface board (jig) to ON.
(The main power of the module is turned on.)
(6) Select the signal used when a problem occurs, or an all white pattern.
(4) Connect the AC power cable to CN61 on the PSU board of the module
requested for repair.
PDP go Switch
ON
OFF
CN1
CN5
– 32 –
4.5 FAULT SYMPTOM
NO
Fault
contents
Fault status
Suspected
fault location
Analysis procedure
and measure
1
After momentarily going on, the
screen becomes black
immediately or after a few
seconds. (Main power is turned
off.)
screen becomes black
immediately or after a few
seconds. (Main power is turned
off.)
X-SUS
Y-SUS
PSU
Panel chassis
LOGIC
ABUSL
ABUSR
Y-SUS
PSU
Panel chassis
LOGIC
ABUSL
ABUSR
Refer to Chapter
4.6.1
4.6.1
2
Entire
screen does
not light.
screen does
not light.
Screen lights dimly even on the
back screen.
back screen.
LOGIC Replace
LOGIC
board
3
Single vertical line (of different
color)
color)
Panel chassis
LOGIC
LOGIC
Refer to Chapter
4.6.2
4.6.2
4
Vertical line
Vertical line from the middle of
effective scan area (Vertical line
of different color)
effective scan area (Vertical line
of different color)
Panel chassis
Replace panel
chassis
chassis
5
Bar width of 1/7 of horizontal size
or in multiples of 1/7, is
displayed. Abnormal display.
or in multiples of 1/7, is
displayed. Abnormal display.
Panel chassis
ABUSL
ABUSR
LOGIC
Above boards
are connected
ABUSL
ABUSR
LOGIC
Above boards
are connected
.
Refer to Chapter
4.6.2
4.6.2
6
Vertical bar
Bar width of 3/7 or 4/7 of the
screen width, is displayed.
Abnormal display. (Vertical line of
different color)
screen width, is displayed.
Abnormal display. (Vertical line of
different color)
ABUSL
ABUSR
LOGIC
Above boards
are connected.
ABUSR
LOGIC
Above boards
are connected.
Refer to Chapter
4.6.2
4.6.2
7
Single horizontal line (No light) or
single horizontal line does not
light among the effective
scanning area.
single horizontal line does not
light among the effective
scanning area.
Single horizontal line does not
light.
light.
Panel chassis
Replace panel
chassis
chassis
8
Horizontal
line
line
Every other line(No light)
Entire screen
X-SUS
Y-SUS
Replace
X-SUS
Y-SUS
Board
Y-SUS
Board
Click on the first or last page to see other KE-37XS910 / KE-42XS910 / KE-MX37A1 / KE-MX37N1 / KE-MX37S1 service manuals if exist.