Sony KDL-65W850A / KDL-65W855A Service Manual ▷ View online
RB1G
CHASSIS
W850/855A
Service Adjustment
Save Changing Data by Service Mode 2
1.
In “Digital” service mode ( “002 MODEL” category)
000 SEGSelect segment information
S S
f
Only when B* board is replaced.
4-5. Restore WB / Gamma Adj. Data to B board.
HG,TE, CM, MH Models
Please apply after USB-DL when B board is replaced.
001 DESTSelect destination information
002 MODELNAMESelect Model Name
003 SERIALCan be set Only Once for the new board
005 VAR_TYPESelect variable information (Refer to Pg80 4-5.)
002 MODELNAMESelect Model Name
003 SERIALCan be set Only Once for the new board
005 VAR_TYPESelect variable information (Refer to Pg80 4-5.)
a.
Change data for each model. (Refer to Pg79 4-4.) except
1.in “VPC” service mode
a.Select “000 DATA_COPY” category by pressing “2 / 5” on remote.
b.Change data from “0” to “1” by pressing “3 / 6” on remote.
c.Wait until data is changed from 1 to 3.
d When data is changed from 1 to 3 restoring process is finished
b.Change data from “0” to “1” by pressing “3 / 6” on remote.
c.Wait until data is changed from 1 to 3.
d When data is changed from 1 to 3 restoring process is finished
VAR_TYPE.
b.
Press “Mute”, “0” on remote sequentially. Red “
WRITE
” is
shown. This indicates writing is in process.
c.
After a while, red “
WRITE
” disappears. Green
Done
will be
di
l
d f
hil
hi h
i i
i d
d.When data is changed from 1 to 3, restoring process is finished.
e.In case data is changed from 1 to 2, keep default setting. (No
more process is needed.)
e.In case data is changed from 1 to 2, keep default setting. (No
more process is needed.)
VPC
SERVICE
displayed for a while, which means writing process is done.
d.
d.
For the items SEG, DEST, MODELNAME after changing
For the items SEG, DEST, MODELNAME after changing
each item, service save (“mute”+”0”) is required. For the
each item, service save (“mute”+”0”) is required. For the
each item, service save (“mute”+”0”) is required. For the
item SERIAL, after inputting the serial number, press key
item SERIAL, after inputting the serial number, press key
item SERIAL, after inputting the serial number, press key
“12” or “Enter” to save the data.
“12” or “Enter” to save the data.
“12” or “Enter” to save the data.
b
VPC
SERVICE
000
DATA_COPY
000
BU_TRANS
1
DO NOT POWER OFF
DO NOT TOUCH ANY KEY NOW
DO NOT TOUCH ANY KEY NOW
12 or Enter to save the data.
12 or Enter to save the data.
–
–
Please save the items according to the sequence “SEG
Please save the items according to the sequence “SEG -->
>
DEST
DEST --> MODELNAME
> MODELNAME
–
–
When Saving the item "SEG", sometimes instead of
When Saving the item "SEG", sometimes instead of
"Writing", the word "Pending" will appear. In this case, skip
"Writing", the word "Pending" will appear. In this case, skip
"Writing", the word "Pending" will appear. In this case, skip
a
b
VPC
SERVICE
000
DATA_COPY
000
BU TRANS
3
Restore process
Writing , the word Pending will appear. In this case, skip
Writing , the word Pending will appear. In this case, skip
"SEG", saving "DEST“ and "MODELNAME“ is OK.
"SEG", saving "DEST“ and "MODELNAME“ is OK.
DIGITAL
SERVICE
002 MODEL
000 SEG
000 SEG
HG_BASE
Write
a
a
a
000
BU_TRANS
3
DATA TRANSFER SUCCESS
Write
VIDEO:STANDARD AUDIO:STANDARD
PSAVE:STANDARD
PSAVE:STANDARD
MAIN: SUB:
TUNER/----/---- ----/----/NTSCU
TUNER/----/---- ----/----/NTSCU
X
/
X
/
b
b
Remote Commander
End restore process
----X----/----- ----X----/-----
-----/---
-----/---
-----/---
DIGITAL Service menu
Remote Commander
125
RB1G
CHASSIS
W850/855A
Service Adjustment
4-6. WB Adjustment by Service Mode
1. in “VPC” service mode (“004 WB” category)
a.
Press “1” or “4” on remote to select WB adjustment menu.
b
Change data by pressing “3” or “6” Each range of these
4-7-2. STEP2 (CM/MH is not supported)
VPC
SERVICE
2.in “VPC” service mode
a.
Select “002 VCOM” category by pressing
b.
Change data by pressing 3 or 6 . Each range of these
items is 0~1023.
items is 0~1023.
c.
Press “mute” ＋”0” on remote to save the data. “SERVICE”
comment is changed to “WRITE”, indicating writing process.
comment is changed to “WRITE”, indicating writing process.
d.
After a while, “WRITE” comment returns to “SERVICE”,
which means writing process is done (takes about a couple
which means writing process is done (takes about a couple
a
VPC
SERVICE
002
VCOM
000 ENABLE 0
“2 / 5” on remote.
b.
Select “000 ENABLE” item by pressing “1
/ 4” on remote.
/ 4” on remote.
c.
Change ENABLE from “0” to “1” by
pressing “3” to enable VCOM adjustment.
pressing “3” to enable VCOM adjustment.
which means writing process is done. (takes about a couple
of seconds)
of seconds)
c
b
VPC
SERVICE
003
WB
001
G_DRV
512
VPC
SERVICE
003
WB
004
G_BKG 512
4-7-3. STEP3 (CM/MH is not supported)
VPC
SERVICE
002
VCOM
001
ADJUST
64
3.
in “VPC” service mode
a.
Select “002 VCOM” category by
pressing “2 / 5” on remote.
pressing “2 / 5” on remote.
VPC
SERVICE
003
WB
Remote
Commander
Commander
VPC
SERVICE
003
WB
002
B_DRV
512
VPC
SERVICE
003
WB
VPC
SERVICE
003
WB
005
B_BKG
512
001 ADJUST 64
p
g
b.
Select “001 ADJUST” item by
pressing “1 / 4” on remote.
pressing “1 / 4” on remote.
c.
Change data by pressing “3 / 6” on
remote.
remote.
003
WB
000
R_DRV
512
VPC Service menu
003
R_BKG
512
4-7-1. STEP1
DIGITAL SERVICE
007 VCOM
000 SRV OSD EN
000 SRV OSD EN
1
4-7-4. STEP4 (CM/MH is not supported)
4.
in “Digital” service mode
a.
Select “007 VCOM” category by
pressing “2 / 5” on remote.
pressing “2 / 5” on remote.
b.
Change data from “1” to “0” by
4-7. VCOM Adjustment (NFR-AUO Panel) (CM/MH is not supported)
4 7 1. STEP1
DIGITAL (DIG_SRV_MODE) SERVICE
TEST PATTERN
--> 1 Video
*1 White
1. in “Digital” service mode
a.
Select “003 DIG_SRV_MODE”
category by pressing “2 / 5” on
remote.
category by pressing “2 / 5” on
remote.
b
Press “0” to go to “TEST PATTERN”
000 SRV_OSD_EN 1
VIDEO:STANDARD AUDIO:STANDARD
PSAVE:STANDARD
PSAVE:STANDARD
MAIN: SUB:
TUNER/
TUNER/
/
/
/NTSCU
b.
Change data from 1 to 0 by
pressing “3 or 6 ” on remote.
pressing “3 or 6 ” on remote.
c.
Confirm the final result of the
VCOM adjustment .
VCOM adjustment .
d.
If OK, Finish the VCOM
adjustment. If NG, pressing “3 or
adjustment. If NG, pressing “3 or
1 White
2 Ramp
3 R Raster
4 G Raster
5 B Raster
6 Color Bar
3 R Raster
4 G Raster
5 B Raster
6 Color Bar
7 VCOM Pattern1
8 VCOM Pattern2
8 VCOM Pattern2
b.
Press 0 to go to TEST PATTERN
Mode.
Mode.
c.
Press “Enter” or “12” to go into
Video TEST PATTERN.
Video TEST PATTERN.
d.
Press “7” or “8” to select the test
pattern
pattern
TUNER/----/---- ----/----/NTSCU
----X----/----- ----X----/-----
-----/---
----X----/----- ----X----/-----
-----/---
-----/---
adjustment. If NG, pressing 3 or
6” to show the OSD again and
go back to VCOM adjustment
Step 3.
6” to show the OSD again and
go back to VCOM adjustment
Step 3.
126
8 VCOM Pattern2
9 Off
pattern
e.
Press “Enter” or “12” twice to show
the VCOM TEST PATTERN.
the VCOM TEST PATTERN.
RB1G
CHASSIS
W850/855A
Service Adjustment
4-8-1. STEP1
4-8. VCOM Adjustment (HFR-SDC Panel) (CM/MH is not supported)
1.
in “VPC” service mode
S l
t “002 VCOM”
t
b
i
“2 /
2.
in detailed REC setting screen
a.
Press “1” to select “Key Copy” item
b.
Press “Enter” or “12” twice to execute the command.
4-9-2. STEP2
VPC
SERVICE
002
VCOM
000 ENABLE 0
a.
Select “002 VCOM” category by pressing “2 /
5” on remote.
5” on remote.
b.
Select “000 ENABLE” item by pressing “1 / 4”
on remote..
on remote..
c.
Change ENABLE from “0” to “1” by pressing
“3” t
“3” t
bl VCOM dj
t
t
b.
Press Enter or 12 twice to execute the command.
c.
If OK, show the message “Key Copy OK”. If NG, show the message
“Key Copy NG (= xx )”.
“Key Copy NG (= xx )”.
d.
Press “Return” to return to previous page.
DIGITAL (
DIG_SRV_MODE)
SERVICE
REC SETTING
DIGITAL (
DIG_SRV_MODE
) SERVICE
REC SETTING
“3” to enable VCOM adjustment.
4-8-2. STEP2
2.
in “VPC” service mode
a.
Select “002 VCOM” category by pressing
REC_SETTING
* 1 Key Copy
2 HDD Re-Register
Key Copy OK
REC_SETTING
* 1 Key Copy
2 HDD Re-Register
Key Copy NG ( xx )
VPC
SERVICE
002
VCOM
001 ADJUST 64
g y y p
g
“2 / 5” on remote.
b.
Select “001 ADJUST” item by pressing “1 /
4” on remote.
4” on remote.
c.
Change data by pressing “3 / 6” on remote.
Every time you push the button, an
Every time you push the button, an
xx value representation
1
decryption failure
2
file acquisition error
y
y
p
evaluation screen is displayed for 5
seconds.
seconds.
d.
Finish the adjustment when the picture
seems OK.
seems OK.
3.
in detailed REC setting screen
a
Press “2” to select “HDD Re-Register” Item
4-9-3. STEP3
4 9 REC Setting (Only for JP/AEP/AUS/NZ)
3
others
DIGITAL (DIG_SRV_MODE) SERVICE
REC_SETTING
4-9-1. STEP1
a.
Press 2 to select HDD Re Register Item.
b.
Press “Enter” or “12” twice to execute the command.
c.
If OK, xx= x+1. If NG, xx=x.
d.
Press “Return” to return to previous page.
4-9. REC Setting (Only for JP/AEP/AUS/NZ)
xx value representation
* 1 Key Copy
2 HDD Re-Register
1. in “Digital” service mode
a.Select “003 DIG_SRV_MODE” category by pressing “2 / 5” on remote.
DIGITAL (
DIG_SRV_MODE
)
SERVICE
REC_SETTING
1 Key Copy
* 2 HDD Re-Register
0
register success
1
HDD repetition
2
file acquisition error
3
HDD i f
i
h
127
b. Select “006 REC_SETTING ” item by pressing “1 / 4” on remote.
c. Press “0” or “10” to go to detailed REC Setting screen.
c. Press “0” or “10” to go to detailed REC Setting screen.
(x) HDDs OK ( xx )
3
HDD info miss-match
4
other
RB1G
CHASSIS
W850/855A
Service Adjustment
4-10. Reset Panel Operation Time
1.
In Self Diagnosis Display (Refer to p.27)
a Reset Panel Operation Time <7> -> <0>
a Reset Panel Operation Time <7> -> <0>
Only when Panel is replaced.
1.
How to do shipping condition.
a.
Move to “Digital” service mode.
b
Press “8” on remote It shows green “SERVICE” changes to
4-11. Set to Shipping Condition
a. Reset Panel Operation Time <7> -> <0>
Remote Commander
b.
Press 8 on remote. It shows green SERVICE changes to
green “RST-”.
green “RST-”.
c.
Press “mute” on remote. Added green “EXE” after green
“RST-” .
“RST-” .
d.
Press “0” on remote. Green “EXE-RST” changes to red “EXE-
RST” It indicate writing is processing
RST” It indicate writing is processing
<Another way>
a
a
SELF CHECK
002 MAIN_POWE ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ 00 Model Name : KDL‐46W90AA
003 AFE I2C
00 Serial Number
:
RST . It indicate writing is processing.
e.
After a while, red “EXE-RST” changes to green “SERVICE”.
f.
And blink Smart Core WHITE LED. Writing process is done
at this point.
at this point.
c
d
b
SONY
<Another way>
You can set to shipping condition w/o entering Service Mode.
-> “Cursor Up” + “Power Key” on remote.
003 AFE_I2C ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ 00 Serial Number : ‐‐‐‐‐‐‐‐
003 DC_ALERT ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ 00 Package Number : PKG1.301JPA
003 AUD_PROT ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ 00 Wired MAC : 30:F9:ED:04:2C:17
003 HDMI_EQ ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ 00 Wireless MAC : F0:F0:02:AA:82:DA
003 TU_DEMOD ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ 00 USB dongle : N/A
003 AFE SPI
‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ 00
Remote Commander
4-12. Summary of Service Control
``
_
004 VLED ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ 00 <MAIN> <EXT>
004 LD_ERR ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ 00 DM1.301JPA WF:2.0.0.99
005 TCON_ERR 120823132523 ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ 01 WF1.003W00AA WF:0B
005 P_ID_ERR ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ 00 DF1.001W00AA FD:‐.‐‐‐
006 BACKLITE ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ 00 YM1.010W00AA BT:1.2.14.848
Function
The flow of control
Service mode on
<Test>+<TV>/<Display><5><Vol Up><Power>
Service mode off
<Other> / <Power off + on>
It
/ d
<1>/<4>
4 12. Summary of Service Control
007 TEMP_ERR ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ 00 M4.992C
007 FAN_ERR
‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ 00 DM1.301W00AA
008 VPC_WDT
‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ 00 DD1.016W00AA
008 MEPS_WDT ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ 00 PK1.016W00AA
008 HOST_WDT ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ 00 AM01.300JP
Item up / down
<1>/<4>
Category up / down
<2>/<5>
Data up / down
<3>/<6>
Test reset (テストリセット)
<8> + <Mute> + <0>
008 STBY_WDT ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ 00
008 AFE_WDT ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ 00 MID:1C117081
010 EMIT_ERR ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐ 00 PID:04020000
PNL:LC470EUF‐FFP1
00081‐000671‐00088 0000000000000570‐0000000000000132
PANEL OPERATION TIME
PANEL OPERATION TIME
HDD Deregistration
(HDD登録削除)
From UI Menu:
HDD登録削除 (JPモデル)
HDD Deregistration (AEP Model)
Execute (実行)
<10 or 0>
(書込み)
128
Diagnosis Display
Write data (書込み)
<Mute> + <0>
Change module (モジュール変更)
<Jump> / <Option>
