DOWNLOAD Sharp PG-B10S (serv.man13) Service Manual ↓ Size: 240.08 KB | Pages: 1 in PDF or view online for FREE

Model
PG-B10S (serv.man13)
Pages
1 Few pages! See other manuals at the bottom of the first or last page.
Size
240.08 KB
Type
PDF
Document
Service Manual
Brand
Device
Projector / (9) Resetting lamp counter
File
pg-b10s-sm13.pdf
Date

Sharp PG-B10S (serv.man13) Service Manual ▷ View online

22
PG-B10S
RESETTING THE TOTAL  LAMP TIMER
Resetting the total lamp timer
When replacing the lamp, reset the total lamp timer in the procedure below.
The warning lights on the projector indicate problems inside the projector.
If a problem occurs, either the temperature warning indicator or the lamp replacement indicator will illumi-
nate red, and the power will turn off. After the power has been turned off, follow the proce-duresgiven
below.
Replacing the Air Filter
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
1
Connect the power cord.
Plug the power cord into the AC socket
of the projector.
2
Reset the lamp timer.
While simultaneously holding down 
and
 on the projector, press 
and
 on the projector.
“LAMP 0000H” is displayed, indicating
that the lamp timer is reset.
Info
Make sure to reset the lamp timer only
when replacing the lamp. If you reset the
lamp timer and continue to use the same
lamp, this may cause the lamp to become
damaged or explode.
AC socket
AUTO SYNC
button
ON button
buttons
Maintenance indicator
Condition
Problem
Possible Solution
Temperature
warning
indicator
Normal
Abnormal
Off
Red on/
Standby
The internal
temperature is
abnormally high.
Abnormal
 Blocked air intake
Relocate the projector to an area
with proper ventilation.
Clean the air filter of the projector.
Cooling fan break-
down
Internal circuit failure
Clogged air intake
Take the projector to your nearest
Sharp Authorized Projector Dealer
or Service Center for repair.
Lamp
indicator
Red on/
Standby
The lamp does
not illuminate.
Burnt-out lamp
Lamp circuit failure
Carefully replace the lamp. 
Take the projector to your nearest
Sharp Authorized Projector Dealer
or Service Center for repair.
Please exercise care when
replacing the lamp.
Red on
Time to change
the lamp.
Remaining lamp life
becomes 5% or less.
Power
indicator
The power
indicator blinks
in red when the
projector is on.
The filter cover or
lamp unit cover is
open.
Securely install the cover.
If the power indicator blinks in red
even when the filter cover and
lamp unit cover is securely
installed, contact your nearest
Sharp Authorized Projector Dealer
or Service Center for advice.
Green on/
Red on
Red blinks
Green on
Green blinks
when the
lamp is
warming up.
1
2
Tab
• This projector is equipped with air fil-
ters to ensure the optimal operating
condition of the projector.
• The air filters should be cleaned every
100 hours of use. Clean the filters more
often when the projector is used in a
dusty or smoky location.
• Ask your nearest Sharp Authorized Pro-
jector Dealer or Service Center to ex-
change the filter (PFILDA010WJZZ)
when it is no longer possible to clean.
Cleaning and Replacing
the Air Filter
1
Press
 on the projector
or
STANDBY
 on the remote control to
put the projector into the
standby mode.
Wait until the cooling fan stops.
2
Disconnect the power cord.
Unplug the power cord from the AC
socket.
3
Remove the filter cover.
Turn the projector over. Loosen the user
service screw (
1
) that secures the fil-
ter cover. Pressing the tab, remove the
filter cover (
2
).
STANDBY button
Air filter (not removable)
User service screw
Air filter (removable)
"
"
"
"
Bottom view
"
"
"
"
Front view
STANDBY
button
STANDBY
AC socket
4
Remove the air filter.
Pick the air filter up with your fingers and
lift it out of the filter cover.
5
Clean the air filter.
Clean the dust off the air filter and cover
with a vacuum cleaner extension hose.
6
Replace the air filter.
Place the air filter underneath the tabs
on the filter cover.
7
Replace the filter cover.
Align the tab on the filter cover and place
it while pressing the tab to close it (
1
).
Then tighten the user service screw (
2
)
to secure the filter cover.
1
2
Tab
User service screw
Note
Be sure the filter cover is securely installed.
The power will not turn on unless it is
correctly installed.
If dust or dirt has collected inside the rear
and bottom air filters (not removable), clean
the filter with a vacuum cleaner extension
hose.
Display

Sharp PG-B10S (serv.man13) Service Manual ▷ Download

  • DOWNLOAD Sharp PG-B10S (serv.man13) Service Manual ↓ Size: 240.08 KB | Pages: 1 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sharp PG-B10S (serv.man13) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp PG-B10S (serv.man13) Projector. Information contained in Sharp PG-B10S (serv.man13) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.