Sony KDL-46XBR8 / KDL-55XBR8 Service Manual ▷ View online
21
KDL-46XBR8/55XBR8
KDL-46XBR8/55XBR8
5
3
4
2
2
1
7
6
Bottom VESA Bracket
Top VESA
Bracket
AC Inlet
AC Bracket
Top Frame
KDL-46XBR8 ONLY
Bottom Frame
1-11. STRUCTURAL FRAMES, BRACKETS AND AC INLET REMOVAL
1 Remove 2 screws from Top Frames
2 Remove 2 screws from Top VESA Bracket (KDL-46XBR8 Only)
Remove 4 screws from Top VESA Brackets (KDL-55XBR8 Only)
3 Remove 1 screw from AC Bracket
4 Remove 2 screws from AC Inlet
5 Remove 4 screws from Bottom VESA Brackets
6 Remove 8 screws from Bottom Frame
7 Remove 4 screws from Bottom Frame
22
KDL-46XBR8/55XBR8
KDL-46XBR8/55XBR8
1-12-1. CLEANING THE LCD PANEL
CAUTION: When cleaning the TV, be sure to unplug the power cord to avoid any chance of electric shock.
1 Clean the cabinet of the TV with a dry soft cloth.
2 Wipe the LCD screen gently with a soft cloth.
→ Stubborn stains may be removed with a cloth slightly moistened with a solution of mild soap and warm water.
→ If using a chemically pretreated cloth, please follow the instruction provided on the package.
→ Never use strong solvents such as a thinner, alcohol or benzine for cleaning.
→ Periodic vacuuming of the ventilation openings is recommended to ensure to proper ventilation.
1-12. LCD PANEL REMOVAL
1 Remove 2 screws
2 Disconnect 2 connectors (KDL-46XBR8 Only)
Disconnect 3 connectors (KDL-55XBR8 Only)
3 Remove 2 screws
1
3
2
LCD Panel
Front Assembly
FIN Panel
NOTE:
The LVDS cable can only be installed one way. There is colored tape on the cable to determine which side is attached
to the CB1 Board and which side is attached to the FBU Board.
23
KDL-46XBR8/55XBR8
KDL-46XBR8/55XBR8
1-13. TOUCH SENSOR MODULE REMOVAL
1 Disconnect 1 connector and remove Illumination Module from Center Cabinet
2 Release Touch Holder from Center Cabinet
3 Disconnect 1 connector and remove Touch Sensor Module from Center Cabinet
4 Carefully remove Touch Sheet from Center Cabinet
CAUTION:
Touch
Sensor
Removal
The board has been installed and fi xed in position on the bezel by double sided tape. Improper removal may cause damages
on both board and light guide. Do not bend or warp board as shown on the picture on the left (shown on sample picture “NG”).
on both board and light guide. Do not bend or warp board as shown on the picture on the left (shown on sample picture “NG”).
To Remove the Module:
1 Hold 2 positions (or more) to minimize board distortion.
2 Use jigs (wide plates) to avoid damaging light guide while separating the module from Bezel (shown on sample picture “OK”).
1
3
4
2
Illumination Module
Touch Holder
Touch Sensor Module
Touch Sheet
“NG”
“OK”
24
KDL-46XBR8/55XBR8
KDL-46XBR8/55XBR8
WIRE DRESSING
THE WIRE DRESSING DIAGRAMS ARE
CURRENTLY NOT AVAILABLE.
CURRENTLY NOT AVAILABLE.
Click on the first or last page to see other KDL-46XBR8 / KDL-55XBR8 service manuals if exist.