Sony HCD-H100 / MHC-C10 / MHC-G100 (serv.man2) Service Manual ▷ View online
— 1 —
COMPACT DISC DECK RECEIVER
SERVICE MANUAL
— Continued on next page —
AEP Model
UK Model
E Model
Australian Model
HCD-H100 is the tuner, deck, CD and
amplifier section in MHC-C10/G100.
amplifier section in MHC-C10/G100.
Photo: E model
HCD-H100
DECK-A
DECK-B
Tape Transport
Mechanism Type
Model Name Using Similar Mechanism
NEW
Base Unit Type
CD94V5CP
Model Name Using Similar Mechanism
NEW
ZY-318-FW-K-130-3
ZY-318-FW-K-130-3
SPECIFICATIONS
CD player section
System
System
Compact disc digital
audio system
audio system
Laser
Semiconductor laser
λ = 780 nm
Emission duration:
continuous
λ = 780 nm
Emission duration:
continuous
Laser output
Max. 44.6
µ W*
* This output is the
value measured at a
distance of 200 mm
from the objective lens
surface on the Optical
Pick-up Block with
7 mm aperture.
distance of 200 mm
from the objective lens
surface on the Optical
Pick-up Block with
7 mm aperture.
Wavelength
780 – 790 nm
Frequency response
2 Hz – 20 kHz (
±0.5 dB)
Tuner section
FM stereo, FM/AM superheterodyne
tuner
FM stereo, FM/AM superheterodyne
tuner
FM tuner section
Tuning range
87.5 – 108.0 MHz
Antenna
FM lead antenna
Antenna terminals
75 ohm unbalanced
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
EXCEPT E, Singapore model:
EXCEPT E, Singapore model:
531 – 1,602 kHz
(with the tuning
interval set at 9 kHz)
(with the tuning
interval set at 9 kHz)
E, Singapore model:
531 – 1,602 kHz
(with the tuning
interval set at 9 kHz)
530 – 1,710 kHz
(with the tuning
interval set at 10 kHz)
(with the tuning
interval set at 9 kHz)
530 – 1,710 kHz
(with the tuning
interval set at 10 kHz)
Intermediate frequency
450 kHz
Amplifier section
AEP, UK, German model:
DIN power output
AEP, UK, German model:
DIN power output
12 W + 12 W
(8 ohms at 1 kHz, DIN)
(8 ohms at 1 kHz, DIN)
Continuous RMS power output
15 W + 15 W
(8 ohms at 1 kHz, 10% THD)
(8 ohms at 1 kHz, 10% THD)
Music power output
24 W + 24 W
(8 ohms at 1 kHz, 10% THD)
(8 ohms at 1 kHz, 10% THD)
Other model:
Peak music power output
Peak music power output
250 W
Continuous RMS power output
18 W + 18 W (8 ohms at 1 kHz,
10 % THD)
10 % THD)
Outputs
PHONES (stereo phone jack):
accepts headphones of 8 ohms
or more.
or more.
SPEAKER:
accepts impedance of 8 to
16 ohms.
16 ohms.
CD
SECTION
TAPE
SECTION
9-960-496-32
2001KI0200-1
© 2001.11
Sony Corporation
Home Audio Company
Published by Sony Engineering Corporation
Ver 1.1 2001. 11
— 2 —
Tape player section
Recording system
4-track 2-channel stereo
Frequency response
60 – 13,000 Hz (
±
3 dB),
using Sony TYPE I
cassette
cassette
General
Power requirements
AEP, UK, German model:
220 – 230 V AC, 50/60 Hz
Australian model:
240 V AC, 50/60 Hz
Mexican model:
120 V AC, 60 Hz
Other model:
110 – 120V or 220 – 240 V
AC Adjustable, 50/60 Hz
AC Adjustable, 50/60 Hz
Power consumption
AEP, UK, German model:
90 watts
Other model:
110 watts
Dimensions
Approx. 275 x 312 x 332 mm
(10 7/8 x 12 3/8 x 13 1/8 in) (w/h/d)
incl. projecting parts and controls
(10 7/8 x 12 3/8 x 13 1/8 in) (w/h/d)
incl. projecting parts and controls
Mass
AEP, UK, German model:
Approx. 5.8 kg (12 lb 13 oz)
Other model:
Approx. 6 kg
Approx. 5.8 kg (12 lb 13 oz)
Other model:
Approx. 6 kg
Design and specifications are subject to
change without notice.
change without notice.
MODEL IDENTIFICATION
— AC POWER SUPPLY CODE —
— AC POWER SUPPLY CODE —
AEP, German model
(Without voltage selector)
E, Singapore model
(With voltage selector)
UK model
Mexican model
Australian model
— 3 —
SAFETY-RELATED COMPONENT WARNING !!
COMPONENTS IDENTIFIED BY MARK
!
OR DOTTED
LINE WITH MARK
!
ON THE SCHEMATIC DIAGRAMS AND
IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
exceeding the limit for Class 1.
This caution
label is located
inside the unit.
label is located
inside the unit.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous ra-
diation exposure.
other than those specified herein may result in hazardous ra-
diation exposure.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
This appliance is classified as a
CLASS 1 LASER product. The
CLASS 1 LASER PRODUCT
MARKING is located on the rear
exterior.
CLASS 1 LASER product. The
CLASS 1 LASER PRODUCT
MARKING is located on the rear
exterior.
SERVICING NOTE
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-up
block. Therefore, when checking the laser diode emission, observe
from more than 30 cm away from the objective lens.
the disc reflective surface by the objective lens in the optical pick-up
block. Therefore, when checking the laser diode emission, observe
from more than 30 cm away from the objective lens.
Jig
It will become easier to operate by using the following extension jig
between the front panel board (CN601) and the CD DECODER board
(1/2) (CN06) when repairing.
between the front panel board (CN601) and the CD DECODER board
(1/2) (CN06) when repairing.
Part No.
Description
J-2501-020-A
EXTENSION CABLE 18P
— 4 —
TABLE OF CONTENTS
Section
Title
Page
SECTION 1. GENERAL
....................................................... 5
SECTION 2. DISASSEMBLY
2-1.
CD Block ............................................................................. 6
2-2.
Bottom Cabinet .................................................................... 6
2-3.
Main Board .......................................................................... 7
2-4.
Front Panel Board and Cassette Deck Assembly ................ 7
SECTION 3. MECHANICAL ADJUSTMENTS
............ 8
SECTION 4. ELECTRICAL ADJUSTMENTS
DECK Section ............................................................................... 8
TUNER Section ........................................................................... 10
CD Section ................................................................................... 12
TUNER Section ........................................................................... 10
CD Section ................................................................................... 12
SECTION 5. DIAGRAMS
5-1.
Circuit Boards Location .................................................... 13
5-2.
Block Diagrams
• CD Section ..................................................................... 14
• Main Section .................................................................. 17
• CD Section ..................................................................... 14
• Main Section .................................................................. 17
5-3.
IC Block Diagrams
— Tuner Section — ........................................................... 20
— Main Section — ............................................................ 20
— Front Panel Section — ................................................. 20
— Tuner Section — ........................................................... 20
— Main Section — ............................................................ 20
— Front Panel Section — ................................................. 20
5-4.
Printed Wiring Board — Main Section — ........................ 22
5-5.
Schematic Diagram — Main Section — ........................... 27
5-6. Schematic Diagram — Front Panel Section —
(AEP, UK, G Model) ......................................................... 31
5-7. Printed Wiring Board — Front Panel Section —
(AEP, UK, G Model) ......................................................... 35
5-8. Printed Wiring Board — Front Panel Section —
(E, MX, SP, AUS Model) ................................................... 40
5-9. Schematic Diagram — Front Panel Section —
(E, MX, SP, AUS Model) ................................................... 45
5-10. Schematic Diagram — CD Decoder Section — ............... 49
5-11. Printed Wiring Board — CD Decoder Section — ............. 53
5-12. Printed Wiring Board — Tuner Section —
5-11. Printed Wiring Board — CD Decoder Section — ............. 53
5-12. Printed Wiring Board — Tuner Section —
(AEP, UK, G Model) ......................................................... 55
5-13. Schematic Diagram — Tuner Section —
(AEP, UK, G Model) ......................................................... 57
5-14. Schematic Diagram — Tuner Section —
(E, MX, SP, AUS Model) ................................................... 60
5-15. Printed Wiring Board — Tuner Section —
(E, MX, SP, AUS Model) ................................................... 63
5-16. IC Block Diagrams — CD Decoder Section — ................ 65
5-17. IC Pin Function
5-17. IC Pin Function
• IC601 System Control, LCD Drive
(
µ
PD753016-H100) ........................................................ 66
Section
Title
Page
SECTION 6. EXPLODED VIEWS
6-1.
Cabinet Section .................................................................. 68
6-2.
CD Deck Section ............................................................... 69
6-3.
Front Panel Section ............................................................ 70
6-4.
Cassette Mechanism Section (ZY-318-FW-K-130-3) ....... 71
6-5.
Base Unit Section (CD94V5CP) ....................................... 72
SECTION 7. ELECTRICAL PARTS LIST
.................... 73
• Abbreviation
G
: German model.
MX : Mexican model.
SP
SP
: Singapore model.
AUS : Australian model.