Sony KDL-40X3000 / KDL-46X3000 Service Manual ▷ View online
- 24 -
FIX2
RM-ED010
During MS update
00’00’’ : update starts by AC ON
EMMA reading MS
(mute)
01’25’’ :
EMMA update starts
03’25’’ :
BEM update starts
(program & NVM)
01’41’’ :
TVM update starts
(program & d ata )
12’55’’ : Update completion except ASUCA
01’19’’ : go to STBY mode
Time (approx.)
LED
TV screen
Display “UPDATING”
Blinking
same as “Power ON”
DL original
No Picture
Blinking
The OSD will d isappear for
about 10sec at the beginning.
about 10sec at the beginning.
Do Not remove
MS or AC
power at this
moment.
MS or AC
power at this
moment.
No Picture
To be continued for upgrading ASUCA after reboot.
- 25 -
FIX2
RM-ED010
Continue to ASUCA (AVC board) update
•
Normal behaviour after upgrading the EMMA2Lr, TVM and BEM.
– TV-Micro
reboots
and resets all micros.
– No picture can be seen for about 1 minute after rebooting since the MS is
still in its slot, therefore the MS image will be read in the flash memory
again.
again.
– After the above, the picture will be seen normally. (This means completion
of the MS update).
•
ASUCA update will continuously start from this state.
– ASUCA update will take approximately 10 minutes.
– Whilst updating ASUCA, the left LED blinks red at 0.5 second intervals.
– Whilst updating ASUCA, the left LED blinks red at 0.5 second intervals.
The LED will stop blinking and return to normal after updating.
• Updating will be processed in the bac kground. Yo u are able to watch the TV as
long as the input se lected is not a digital c hanne l.
• Update will be interrupte d in o ne of the fo llowing conditions. However, it will
auto matically resume at the next o pportunity since the pro gra m is being loade d
fro m the MS to the flash me mory o n the set.
fro m the MS to the flash me mory o n the set.
– Loss of AC Power.
– Power off by power button or remote commander.
– Change of input source to digital channel.
– Power off by power button or remote commander.
– Change of input source to digital channel.
Ending MS update.
•
Unplug the AC cable and remove the memory stick.
•
Enter the service mode using the remote commander and check the
software versions have been updated successfully.
software versions have been updated successfully.
- 26 -
FIX2
RM-ED010
Procedure for Case-2 : Board replacement
(AE board)
Before MS update, enter the service mode using the remote
commander and change the following settings as required. (See page 16).
commander and change the following settings as required. (See page 16).
1.
TVM MODEL(Cate gory 001)/PKGINIT(Ite m 004) (0->1)
2.
TVM NVM_DL(Category 001)/DLCC(Ite m 006) (1->0)
3.
TVM MODEL(Cate gory 001)/SERIES(Ite m 005)
(X=1,W =0)
(X=1,W =0)
1.
“MUTE + 0” (NVM write)
2.
Exit service mode.
MS Update
Refer to
“Starting MS Update”
,
“During MS Update”
and
“ASUCA(AVC board) Update”.
After MS update, enter the service mode using the remote
commander and change the following settings as required. (See Page 16).
1.
TVM MODEL(Cate gory 001)/XBEZEL(Ite m 000)
(Aluminum finishe d=0, Micro ho les/Piano Black=1)
2.
“MUTE + 0” (NVM write)
3.
Verify the version.
4.
Exit service mode.
5.
Perform picture/function check.
Data
Item
Category
Data
Item
Category
Data
Item
Category
Data
Item
Category
- 27 -
FIX2
RM-ED010
Procedure for Case-2 : Board replacement
(FB2 board)
Before MS update, enter the service mode using the remote
commander and change the following settings as required. (See Page 16).
commander and change the following settings as required. (See Page 16).
1.
TVM MODEL(Cate gory 001)/PKGINIT(Ite m 004) (0->1)
2.
Go in to BEM Service menu. (See pa ge 16, 3-4).
3.
BEM Mo del_Info (Cate gory 0002)/Panel_Size(Ite m 0001) (40”=0,
46”=1, 52”=2)
46”=1, 52”=2)
4.
“MUTE + 0” (NVM write)
5.
Exit service mode.
MS Update
Refer to
“Starting MS Update”
,
“During MS Update”
and
“ASUCA(AVC board) Update”.
After MS update, enter the service mode using the remote
commander. (See page 16).
commander. (See page 16).
1.
Verify the version.
2.
Exit service mode.
3.
Perform picture/function check.
40” = 0
46” = 1
52” = 2
BEM SERVICE
0002 Mode l_Info
0001 Pa ne l_Size
0001 Pa ne l_Size
0
Data
Item
Category
Data
Item
Category
Click on the first or last page to see other KDL-40X3000 / KDL-46X3000 service manuals if exist.