Sony KDL-40NX725 Service Manual ▷ View online
KDL-40NX725
44
SECTION 6 - DISASSEMBLY/PART NUMBER INFORMATION
NOTE: The components identified by shading
and
!
mark are critical for safety. Replace only
with part number specified.
NOTE: The components identified by a red outline and a mark contain
confidential information. Specific instructions must be adhered to whenever
these components are repaired and/or replaced.
See Appendix A: Encryption Key Components in the back of this manual.
301
1-838-924-21
CONNECTOR ASSEMBLY
*
302
1-910-801-10
CONNECTOR ASSEMBLY 14P
303
1-910-801-11
CONNECTOR ASSEMBLY 28P
* 304
1-910-801-41
(LVDS) FLEXIBLE FLAT CABLE 56 PIN
REF. NO.
PART NO.
DESCRIPTION
[ASSEMBLY INCLUDES]
REF. NO.
PART NO.
DESCRIPTION
[ASSEMBLY INCLUDES]
305
1-838-849-11
(LVDS) FLEXIBLE FLAT CABLE N1 40S
306
1-910-801-59
HARNESS ASSEMBLY
SCREWS
CONNECTORS
P/N
DESCRIPTION
REMARKS
TOTAL
▲
2-580-608-01
SCREW, +PSW M5X16
TABLE-TOP STAND(3)
3
△
4-256-393-01
SCREW, +PSW M3X6 W12
AC COVER(1), WOOFER(3), CNTR CBNT(3)
7
□
2-580-639-01
SCREW, +BVTP 4X12 TYPE2 IT-3
RC(4)
4
◆
4-257-907-01
JOINT, STAND
RC(2)
2
◇
4-268-126-02
SCREW, ORNAMENTAL M6X12
RC(6)
6
●
2-990-421-41
SCREW (+PSW) (M3X6)
BATL(6), G4(3), LD SHIELD(2), WIFI(1), ANTENNAS(2), CAMERA(1)
15
○
4-258-272-01
SCREW, +PWH M3X8
RC(8), SWITH UNIT(1)
9
★
7-685-646-79
SCREW +BVTP 3X8 TYPE2 IT-3
TERMINAL AREA(1), SIDE BRKT(1)
2
☆
4-259-541-01
USER SCREW ST
HEAD STAND to NECK(1), NECK to BASE STAND(2)
3
KDL-40NX725
301
302
303
304
306
305
KDL-40NX725
45
SECTION 6 - DISASSEMBLY/PART NUMBER INFORMATION
ACCESSORIES AND PACKAGING
4-191-241-01 FLYER
4-273-020-31
MANUAL, INSTRUCTION
MISCELLANEOUS
A-1811-853-A
BAG, SCREW ASSEMBLY(M)
CONTAINS THE FOLLOWING SCREWS
2-580-608-01
SCREW, +PSW M5X16
(SCREWS TO ATTACH TABLE-TOP STAND TO LCD TV)
For product protection and safety reasons, Sony strongly recommends
that you use the screws provided with the TV
CAUTION: These screws cannot be used to secure the TV to
the Wall Mount Brackets
4-259-541-01
USER SCREW ST
(SCREWS TO ATTACH HEAD STAND AND BASE STAND TO NECK)
1-838-791-11
CABLE CONVERSION
4-262-708-01
CLAMPER, CABLE
4-188-302-11
HEX WRENCH
4-257-907-01
JOINT, STAND
(SCREWS USED WHEN STAND IS ATTACHED-NOT USED WITH WALL MOUNTS)
4-256-443-01
SHEET, RADIATION (BAT-L/V)
ORDER THIS PART WHEN REPLACING THE LCD PANEL
X-2549-230-1
SUPPORT BELT KIT
7-632-452-24
TAPE (NO.303) 18MMX35M YEL
*
4-256-601-21
TAPE, BRACKET GL (40SD EL)
REMOTE COMMANDER
1-489-474-21
REMOTE COMMANDER (RM-YD062)
KDL-40NX725
46
SECTION 6 - DISASSEMBLY/PART NUMBER INFORMATION
WIRE DRESSING
FIGURE 6-1. OVERALL WIRE DRESSING
KDL-40NX725 47
SECTION 7 - SERVICE ADJUSTMENTS
OVERVIEW
As mentioned in
“Section 2 - Software Requirements” on page 15
,
the models in this manual utilize a “generic” type Main Board,
therefore certain service adjustments settings must be changed or
confirmed when either the Main Board, LCD Panel, or TCON Board
are replaced.
UPDATING THE SOFTWARE
After replacing the Main Board, LCD Panel, or TCON Board, you
MUST UPDATE the SOFTWARE to the latest version. Instructions
for updating the software are included with the software package
on the Sony Authorized Servicer Portal at
http://www.sony.com/asp
website.
ACCESSING SERVICE ADJUSTMENT
MODE
1. TV must be in standby mode. (Power off).
2. Access Service Mode by pressing the following buttons
on the Remote Commander within a second of each
other:
DISPLAY
Channel 5
Volume +
POWER .
DISPLAY
RM-YD062
5
VOLUME+
POWER
Click on the first or last page to see other KDL-40NX725 service manuals if exist.