DOWNLOAD Sony KDL-40EX1 / KDL-46EX1 / KDL-52EX1 / LDM-E401 / LDM-E461 / LDM-E521 / MBT-W1 Service Manual ↓ Size: 8.97 MB | Pages: 87 in PDF or view online for FREE

The circuit boards used in these models have been processed using
Lead Free Solder. The boards are identified by the LF logo located
close to the board designation e.g. H1 etc [ see example ]. The
servicing of these boards requires special precautions to be taken as
outlined below.

Lead Free Solder material must be used to comply with environmental requirements of new solder joints. Lead Free Solder is available under
the  following part numbers :

Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. This requires
soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics.

For more information on the use of Lead Free Solder, please refer to  http://www.sony-training.com

9

1

-

5

0

0

-

0

4

6

-

7

m

m

3

.

0

g

K

5

2

.

0

0

2

-

5

0

0

-

0

4

6

-

7

m

m

4

.

0

g

K

0

5

.

0

1

2

-

5

0

0

-

0

4

6

-

7

m

m

5

.

0

g

K

0

5

.

0

2

2

-

5

0

0

-

0

4

6

-

7

m

m

6

.

0

g

K

5

2

.

0

3

2

-

5

0

0

-

0

4

6

-

7

m

m

8

.

0

g

K

0

0

.

1

4

2

-

5

0

0

-

0

4

6

-

7

m

m

0

.

1

g

K

0

0

.

1

5

2

-

5

0

0

-

0

4

6

-

7

m

m

2

.

1

g

K

0

0

.

1

6

2

-

5

0

0

-

0

4

6

-

7

m

m

6

.

1

g

K

0

0

.

1

How to replace the fuse.
Open the fuse compartment with
a screwdriver blade and replace
the fuse.

FUSE

WARNING (UK Models only)

The flexible mains lead is supplied connected to a B.S. 1363 fused
plug having a fuse of the correct rating for the set. Should the fuse
need to be replaced, use a fuse of the same rating approved by ASTA
to BS 1362, ie one that carries the 

ASA

T

 mark.

IF THE PLUG SUPPLIED WITH THIS APPLIANCE IS NOT SUITABLE
FOR THE OUTLET SOCKETS IN YOUR HOME, IT SHOULD BE CUT
OFF AND AN APPROPRIATE PLUG FITTED. THE PLUG SEVERED
FROM THE MAINS LEAD MUST BE DESTROYED AS A PLUG WITH
BARED WIRES IS DANGEROUS IF ENGAGED IN A LIVE SOCKET.

When an alternative type of plug is used, it should be fitted with the
correct rating fuse, otherwise the circuit should be protected by the
same rating fuse at the distribution board.

Due to changes in the caution note 
for MDF-61 connector, the caution 
note has been placed in Appendix-A

Locked situation

Housing and Connector 
edge are flush.

Unlocked situation

Housing and Connector 
edge are not flush.

Note:
After the XA connector is attached, confirm the housing edge and connector edge are in the same position as in Fig. 2.

Whilst working on this product, it is not recommended to lay the TV set face down when powered up, as this can result in panel problems. If
it is necessary to power up the TV set when face down, the time should be minimised as much as possible.

TV system

Analogue: Depending on your country selection: B/G/H, D/K, L, I
Digital: DVB-T/DVB-C

Colour/video system

Analogue: PA L, SECAM NTSC 3.58, 4.43 (only Video In)
Digital: MPEG-2 MP@ML/HL, H.264/MPEG-4 AV C [email protected], [email protected]

Channel coverage

Analogue: VHF: E2–E12/UHF: E21–E69/CATV: S1–S20/HYPER: S21–S41
D/K: R1–R12, R21–R69/L: F2–F10, B–Q, F21–F69/I: UHF B21–B69
Digital: VHF/UHF

Aerial

75 ohm external terminal for VHF/UHF

/

 

AV 1

21-pin Scart connector (CENELEC standard) including audio/video input, RGB input and unit 
audio/video output.

 AV 2

Video input (phono jack)

 AV 2

Audio input (phono jacks)

DIGITAL AUDIO OUT (OPTICAL)(digital optical jack)

 COMPONENT IN

Supported formats: 1080p, 1080i, 720p, 576p, 576i, 480p, 480i
Y:  1 Vp-p, 75 ohms, 0.3V negative sync
PB/CB: 0.7 Vp-p, 75 ohms
PR/CR: 0.7 Vp-p, 75 ohms

 COMPONENT IN

Audio input (phono jacks)
500 mVrms

HDMI IN 1, 2, 3

Video: 1080p, 1080i, 720p, 576p, 576i, 480p, 480i
Audio: Two channel linear PCM
32, 44.1 and 48 kHz, 16, 20 and 24 bits
PC Input (See page 8)

PC IN 

PC Input (D-sub 15-pin)
G: 0.7 Vp-p, 75 ohms, non Sync on Green
B: 0.7 Vp-p, 75 ohms, non Sync on Green
R: 0.7 Vp-p, 75 ohms, non Sync on Green
HD: 1-5 Vp-p
VD: 1-5 Vp-p

 PC audio input (minijack)

CAM (Conditional Access Module) slot

i

Headphones jack

USB port

Power requirements

220–240 V AC, 50 Hz

Power consumption

20 W

Standby power consumption*

3.5 W or less (19 W when Quick Start is ON)

Dimensions 
(Approx.) 
(w × h × d)

for vertical 
placement with 
stand

13.1 × 30.2 × 28.6 cm

for horizontal 
placement

28.0 × 7.2 × 28.6 cm

Mass (Approx.)  for  vertical 

placement with 
stand

2.5 kg

for horizontal 
placement

2.4 kg

Transmission system

OFDM

Carrier frequency

5.15 to 5.25 GHz

Transmission distance

30 cm to 20 m (depending on installation / usage)