Sony KD-30XS955 (serv.man2) Service Manual ▷ View online
KD-30XS955/34XS955
22
KD-30XS955/34XS955
Q BOX WIRE DRESSING
KD-30XS955/34XS955
23
KD-30XS955/34XS955
ECG WIRE DRESSING (XS & HS)
DY
Rotation
COIL
COIL
g (
)
Rev. 1
3/11/05
3/11/05
CRT BRKT
Earth Coating
Ground Wire (ECG)
32”: 1-900-808-29
Ground Wire (ECG)
32”: 1-900-808-29
(Earth Coating Ground)
Integral Spring
2-Places
2-Places
NOTE: Leads are
dressed inside
Rotation Coil.
dressed inside
Rotation Coil.
NOTE2: There are
2 Leads (TOTAL 4
Wires) to connect
to CH-Board
2 Leads (TOTAL 4
Wires) to connect
to CH-Board
Caution Points:
1. Make sure braided ECG wire loop does not
twist, and stays flat on CRT surface.
twist, and stays flat on CRT surface.
2. Do not pull excessively on the tension spring
3. If the spring appears warped or stretched,
replace entire parts. The braided ECG wire
CANNOT sag on the CRT, and must remain
under tension.
replace entire parts. The braided ECG wire
CANNOT sag on the CRT, and must remain
under tension.
DY
Rotation
COIL
COIL
Rev. 1
3/11/05
3/11/05
CRT BRKT
NOTE: Leads are
dressed inside
Rotation Coil.
dressed inside
Rotation Coil.
NOTE2: There are
2 Leads (TOTAL 4
Wires) to connect
to CX-Board
2 Leads (TOTAL 4
Wires) to connect
to CX-Board
ECG - P/N
1-900-808-30 - 30 WCRT
1-900-808-31 - 34W CRT
1-900-808-30 - 30 WCRT
1-900-808-31 - 34W CRT
SPRING (2 places)
Integral part of
the Ground wire
the Ground wire
2-022-978-01
Wire Clip (2 Places)
30/34W ECG WIRE DRESSING (XS & HS)
KD-30XS955/34XS955
24
KD-30XS955/34XS955
30/34W XS DGC/LCC CAUTION POINT
DY
Rotation
COIL
COIL
Cable Tie
To CN504/505
on A-Board
on A-Board
LCC
Coil
(Top)
Coil
(Top)
LCC
Coil
(Top)
Coil
(Top)
Rev. 1
3/11/05
3/11/05
Cable Tie
CN5805
[ DL ]
LCC
Coil
(Bottom)
Coil
(Bottom)
LCC
Coil
(Bottom)
Coil
(Bottom)
NOTE: MAKE SURE Cable Tie is
positioned so it does NOT
touch LCC COIL Wires! DO
NOT apply Cable Tie over
white/black LCC Tape!
positioned so it does NOT
touch LCC COIL Wires! DO
NOT apply Cable Tie over
white/black LCC Tape!
NOTE: MAKE SURE wires are
not too tight! Leave some
Slack!
not too tight! Leave some
Slack!
!
!
!
Dress DGC
leads through
Cable Ties!
leads through
Cable Ties!
KD-30XS955/34XS955
25
KD-30XS955/34XS955
DY
Rev. 1
3/11/05
3/11/05
Cable Tie
4-041-041-02
4-041-041-02
STEP1:
Make a loop in leads
and route loop BEHIND
The DGC Coil.
Make a loop in leads
and route loop BEHIND
The DGC Coil.
STEP 2:
Thread both connector
housings through the
loop in lead wires.
Thread both connector
housings through the
loop in lead wires.
STEP 3:
Plug in connector
housings into the
[A] Board using the
loop to take up slack.
Plug in connector
housings into the
[A] Board using the
loop to take up slack.
30/34W DGC LEAD WIRE DRESSING (XS & HS)
Click on the first or last page to see other KD-30XS955 (serv.man2) service manuals if exist.