Sony KD-30XS955 (serv.man2) Service Manual ▷ View online
KD-30XS955/34XS955
14
KD-30XS955/34XS955
HDMI gnd cable is dressed with
Q-box cables
Q-box cables
CHASSIS WIRE DRESSING DETAIL -3
Connect HDMI gnd cable to
HDMI shield cae
HDMI shield cae
CHASSIS WIRE DRESSING DETAIL -4
KD-30XS955/34XS955
15
KD-30XS955/34XS955
CHASSIS WIRE DRESSING DETAIL -5
Add gasket to Antenna Switch
next to Fpin cables
Gasket will be between Ant switch and
Q-box
next to Fpin cables
Gasket will be between Ant switch and
Q-box
1-900-805-24 gnd wire is dressed in
wire clamp p/n 4-857-472-01
wire is dressed BEFORE securing
position of Antenna Switch
wire clamp p/n 4-857-472-01
wire is dressed BEFORE securing
position of Antenna Switch
XS Models do NOT have Sub-Tuner Pin-Plug Cable
XS Models do NOT have iLINK (iEEE) Cable.
F-pin to F-pin cable 1-829-702-11
connect like this
Add Ferrite core 1-543-393-11
(place in the middle of cable)
connect like this
Add Ferrite core 1-543-393-11
(place in the middle of cable)
Note position (rotation of right angle connector)
of cable/ferrite Do NOT dress the ferrite core so
it can touch the Heat Sink on the POD connector
of cable/ferrite Do NOT dress the ferrite core so
it can touch the Heat Sink on the POD connector
CHASSIS WIRE DRESSING DETAIL -6
KD-30XS955/34XS955
16
KD-30XS955/34XS955
CHASSIS WIRE DRESSING DETAIL -7
CHASSIS WIRE DRESSING DETAIL -8
Note "Z" routing of USB cable (Important for EMI)
Position of Ferrite core is important for EMI
Position of Ferrite core is important for EMI
CRITICAL POINT:
14P Conn. Assy. (P-shield to M-Bd, p/n: 1-900-808-41)
MUST be dressed as far back in the chassis as possible.
NOTE position of the ferrite core (adjacent to P-shield).
14P Conn. Assy. (P-shield to M-Bd, p/n: 1-900-808-41)
MUST be dressed as far back in the chassis as possible.
NOTE position of the ferrite core (adjacent to P-shield).
Note 14 Conn. Assy is now connected in the middle
of M board
of M board
Note Direction of wires dressed in
11mm purselock (p/n: 3703-983-02)
11mm purselock (p/n: 3703-983-02)
KD-30XS955/34XS955
17
KD-30XS955/34XS955
CHASSIS WIRE DRESSING DETAIL -9
CHASSIS WIRE DRESSING DETAIL -10
TAB on AZ-Bd is slightly bent at 45degree angle
(towards front of set)
(towards front of set)
Double ground wire is dressed in H-Bracket clip.
TAB on QH-Bd is bent 45degrees away from
memory stick connector.
Reason: If TAB is not bent over, wires may get
snagged on DGC and break tab off PWB when
inserting chassis into set.
memory stick connector.
Reason: If TAB is not bent over, wires may get
snagged on DGC and break tab off PWB when
inserting chassis into set.
UZ-Bd to HB-Bd Conn. Assy.
(with Red taping, p/n: 1-900-806-83)
Dressed in purselock on M-Bd
(p/n: 4-355-912-xx)
(with Red taping, p/n: 1-900-806-83)
Dressed in purselock on M-Bd
(p/n: 4-355-912-xx)
4P WY-Bd to DL-Bd Conn. Assy.
(with Red Housing, p/n: 1-900-808-02)
(with Red Housing, p/n: 1-900-808-02)
Dressed in purselock on Z-Bd
(p/n: 4-355-912-xx)
(p/n: 4-355-912-xx)
Both 1-900-806-83 and 1-900-808-02
dressed in 9mm purselock
(p/n: 3-703-982-02)
dressed in 9mm purselock
(p/n: 3-703-982-02)
Both 1-900-806-83 and 1-900-808-02
dressed in H-Bracket Clip
NOTE:Directions of cables INSIDE clip.
(Black cable dressed in H-Bracket
clip is USB cable
(QBOX to QH-Bd, p/n: 1-829-191-11)
dressed in H-Bracket Clip
NOTE:Directions of cables INSIDE clip.
(Black cable dressed in H-Bracket
clip is USB cable
(QBOX to QH-Bd, p/n: 1-829-191-11)
Click on the first or last page to see other KD-30XS955 (serv.man2) service manuals if exist.