Sony RM-PJAW15 / RM-PJHW15J / RM-PJVW70 / VPL-HW10 / VPL-HW15 Service Manual ▷ View online
1-11
VPL-HW10
1-3-11. GA Board
1-3-12. GB Board
5
Four screws
(PSW M3
x
8)
4
Clamp filter
(Ferrite core)
6
GA board
CN101
CN102
CN103
CN104
CN105
3
Remove the G board cover assembly
in the direction of the arrow
A
.
1
Screw
(BVTP 3
x
12)
2
Three claws
G board cover
A
Fuse connector assembly
1
Four screws
(PSW M3
x
8)
CN201
G board holder block
CN202
CN203
CN302
CN303
CN301
When extending the C board, remove the
connector CN301, and extend the board
using the
connector CN301, and extend the board
using the
K
SH connector assembly.
(Refer to page 1-18.)
2
Clamp filter
(Ferrite core)
3
GB board
When removing the G board, remove it in the
way that the G board should not contact with
the metal plate of the G board holder.
way that the G board should not contact with
the metal plate of the G board holder.
1-12
VPL-HW10
1-3-13. Lamp Power Supply
1-3-14. QB Board
1
Two screws
(BVTP 3
x
12)
6
Lamp power supply
3
Remove the lamp power supply
in the direction of the arrow.
2
Two dowels
Lamp power connector assembly
5
Heat sink (BA), Sheet (BA)
4
Two clips (BA)
X3
X2
X1
Two SP4-40 UNC screws
(No height difference)
(No height difference)
QA board
QB board
1
Two hexagon screws
(There is a height difference. )
2
QB board
CN91
QA board
1-13
VPL-HW10
1-3-15. D.C. Motor and V Board-1
6
Three dowels
1
Two connectors
Front Side
of Unit
of Unit
4
Three screws
(BVTP 3
x
12)
7
G board holder block
A
A
A
A
Rear Side
of Unit
of Unit
5
Remove the lamp power connector
assembly from the claw of fan (CH)
bracket, and from the hole of the
plate clamp.
bracket, and from the hole of the
plate clamp.
Claw of fan (CH) bracket
Hole of plate clamp
D.C. motor block
Lamp power supply
Lamp power supply
X2
X2
X1
X1
Before removing the G board holder block,
remove the harness from the hole.
remove the harness from the hole.
2
Open the two edge clamps
3
Remove the harnesses
from the nine claws.
Lead with connector
(LVDS)
(LVDS)
GA board
Marking is printed on the top.
QA board
CN900
Front Side
of Unit
of Unit
Claw of plate clamp
G board holder block
When installing the harness,
the harness should not protrude
exceeding the shaded area.
the harness should not protrude
exceeding the shaded area.
When installing the
harness, place the
harness at a right angle.
harness, place the
harness at a right angle.
Claw of bottom cover
CN401
CN602
CN605
CN300
CN300
Tape
Chassis
Harness of the lead with connector
(LVDS) should not override on top
of the chassis screw.
(LVDS) should not override on top
of the chassis screw.
Chassis screw
Lead with connector
(LVDS)
(LVDS)
1-14
VPL-HW10
1-3-16. D.C. Motor and V Board-2
2
Three screws
(BVTP 3
x
12)
3
D.C. motor block
4
Two screws
(BVTP 3
x
12)
6
Two screws
(BVTP 3
x
12)
1
Fan connectors
5
V board
7
Two sirocco cushions
!-
Six fan dampers
9
Fan cover
(84C)
0
Fan cover
(84I)
8
Four claws
!=
D.C. motor
CN80
QA board
Front Side
of Unit
of Unit
Label side
Click on the first or last page to see other RM-PJAW15 / RM-PJHW15J / RM-PJVW70 / VPL-HW10 / VPL-HW15 service manuals if exist.