Sony RM-PJAW15 / RM-PJHW15J / RM-PJVW70 / VPL-HW10 / VPL-HW15 Service Manual ▷ View online
2-9
VPL-HW10
2-7-2. SUB CPU Upgrade
1.
Double-click Flash.exe to start the application.
Application name:
Main Flash upgrader for Sony
Projector
Execution file name: Flash.exe
n
When starting the application first, the following errors
When starting the application first, the following errors
may appear. But, continue the procedure.
“No. 300:
“No. 300:
No information file was found.”
“No. 711:
No download file was found.”
2.
Click the [Select] button to select download informa-
tion file.
The file open window appears.
The file open window appears.
3.
Select the download information file.
File to be selected
File to be selected
(HW10/HW15): (hh1v
****.dli/hh2v****.dli)
(
**** means version number. Example: hh1v001a.dli)
4.
Click the [Setting] button of the “Com.”.
5.
Set the following items.
Bit rate:
38,400 bit/s
Serial port: Serial port number used for connecting
PC
Time out:
Arbitrary
(Communication retrial time. default: 5
sec.)
sec.)
6.
Select “User Program Mode”.
7.
Click the [Start] button.
The start window appears.
8.
Click the [OK] button.
The “Please AC Plug In” window appears.
9.
Connect the AC plug.
10. Comfirm the Standby Mode is set to “Standard”.
(Refer to “Preparation” in Section 2-7-1.)
11. Click the [OK] button.
The writing starts and the write window appear.
12. The end window appears. (Upgrade completed)
2-10
VPL-HW10
2-7-3. Scan Converter Upgrade
1.
Connect the AC plug and set this unit to standby state.
2.
Comfirm the Standby Mode is set to “Standard”.
(Refer to “Preparation” in Section 2-7-1.)
3.
Double-click FlashUpgraderForSony35.exe to start the
application.
application.
Application name:
Pixelworks FlashUpgrader
Execution file name: FlashUpgraderForSony35.exe
Version:
3.5 or later
4.
Select the COM port to COM port number used for
connecting PC.
5.
Select the Baud Rate to “115200”.
6.
Click the [Choose...] button.
The file selection window appears.
The file selection window appears.
7.
Select the upgrade file.
File to be selected (HW10/HW15): pw0p
File to be selected (HW10/HW15): pw0p
****.inf
(
**** means version number. Example: pw0p100a.inf)
8.
Check that the two hex files appear on the Files To
Download field.
9.
Click the [Ext|_|232C|PW|_|1] button.
10. Click the [Flash] button.
The upgrading starts and the status bar appears. And
the [Flash] button changes to the [Cancel] button.
11. After completed, check that the [Cancel] button
changes to the [Flash] button.
12. Disconnect the AC plug.
2-11
VPL-HW10
2-7-4. Data Write Method of LookUpTable/3Dgamma/DDC/OGMTable/
CSMatrixTable
1.
Connect the AC plug and set this unit to standby state.
2.
Comfirm the Standby Mode is set to “Standard”.
(Refer to “Preparation” in Section 2-7-1.)
(Refer to “Preparation” in Section 2-7-1.)
3.
When LookUpTable or 3Dgamma data writing, press
the [ON/STANDBY] button to light the lamp.
the [ON/STANDBY] button to light the lamp.
4.
Double-click QuickAccess.exe to start the application.
Application name:
3Dgamma QuickAccess
Execution file name: QuickAccess.exe
Version:
8.20 or later
5.
Select “VPL-HW10” or “VPL-HW15” on the Model
pull-down menu.
6.
Select Load on the Load/Save pull-down menu.
7.
Select the data type (3Dgamma/LookUpTable/DDC/
OGMTable/CSMatrixTable) on the 3dgm/Lut pull-
OGMTable/CSMatrixTable) on the 3dgm/Lut pull-
down menu.
8.
Click the [Next] button.
9.
Select the serial port used for connecting PC on the
Serial Port pull-down menu.
Serial Port pull-down menu.
Upper box: Serial port number used for connecting PC
Lower box: 38400
Lower box: 38400
10. Click the [Next] button.
11. Select “ALL” on the Load field.
12. Check the Verify check box.
12. Check the Verify check box.
13. Click the [Browse...] button and select the data file to
be written.
14. Click the [Next] button.
The massage “There is a wrong file. To continue push
YES.” appears.
15. Click the [YES] button.
The writing is performed.
When completed, the massage “Turn Off and On the
When completed, the massage “Turn Off and On the
AC and then Power On to enable the new settings.”
appears.
appears.
16. Click the [OK] button.
17. Turn off the power and disconnect and connect the AC
17. Turn off the power and disconnect and connect the AC
plug, to restart this unit.
18. Click the [Complete] button.
2-12
VPL-HW10
2-7-5. Data Obtain Method of LookUpTable/3Dgamma/DDC/OGMTable/
CSMatrixTable from the Board
1.
Connect the AC plug and set this unit to standby state.
2.
Double-click QuickAccess.exe to start the application.
Application name:
3Dgamma QuickAccess
Execution file name: QuickAccess.exe
Version:
8.10 or later
3.
Select “VPL-HW10” or “VPL-HW15” on the Model
pull-down menu.
4.
Select Save on the Load/Save pull-down menu.
5.
Select the data type (3Dgamma/LookUpTable/DDC/
OGMTable/CSMatrixTable) on the 3dgm/Lut pull-
OGMTable/CSMatrixTable) on the 3dgm/Lut pull-
down menu.
6.
Click the [Next] button.
7.
Select the serial port used for connecting PC on the
Serial Port pull-down menu.
Serial Port pull-down menu.
Upper box: Serial port number used for connecting PC
Lower box: 38400
Lower box: 38400
8.
Click the [Next] button.
9.
Select “SAVE_ALL” on the Save field.
10. Check the Verify check box.
11. Type an arbitrary file name on the File Name field.
12. Click the [Next] button.
12. Click the [Next] button.
The saving is performed.
When completed, the massage “Verify Success!
When completed, the massage “Verify Success!
Reading Model Name, Serial Number, NVM Map
Version and NVM Data Version is successful.”
Version and NVM Data Version is successful.”
appears.
13. Click the [OK] button.
14. Turn off the power of this unit.
15. Click the [Complete] button.
15. Click the [Complete] button.
Click on the first or last page to see other RM-PJAW15 / RM-PJHW15J / RM-PJVW70 / VPL-HW10 / VPL-HW15 service manuals if exist.