Sony RM-PJAW15 / RM-PJHW15J / RM-PJVW70 / VPL-HW10 / VPL-HW15 Service Manual ▷ View online
1-7
VPL-HW10
1-3-6. C Board-1
Remove it while
pressing the claw
of the connector.
pressing the claw
of the connector.
Claw
3
Remove the G board cover assembly
in the direction of the arrow
A
.
1
Screw
(BVTP 3
x
12)
2
Three claws
4
Two screws
(BVWHTP 3
x
12)
5
Lamp power
connector assembly
7
Two fan connectors
6
Six claws
harness
HB board
CN20
CN20
G board cover
A
![
Press the
two claws.
!=
Three harnesses
Fuse connector assembly
!-
Remove the fuse connector assembly
in the direction of the arrow
B
.
Fuse connector assembly
!\
Two harnesses
Connector
C board
CN101
CN101
From CN900
on the QA board.
on the QA board.
C board
CN100
CN100
TL board
CN60
CN60
0
Loosen screw.
Marking is printed
on the bottom.
on the bottom.
!]
Lead with connector
(LVDS)
B
To the D.C. fan cover
(VPL-HW10), or
chassis (VPL-HW15).
(VPL-HW10), or
chassis (VPL-HW15).
8
Screw
(PSW 3
x
8)
9
GND wire
harness
When installing the GND wire harness,
insert the GND wire harness in between
the optical unit and the bottom cover
assembly.
insert the GND wire harness in between
the optical unit and the bottom cover
assembly.
The lug terminal should not
protrude exceeding the chassis.
protrude exceeding the chassis.
Bottom cover
assembly
assembly
Optical unit
Rear Side
of Unit
of Unit
Pull the GND harness front to
give tension.
give tension.
D.C. fan cover (VPL-HW10), or
chassis (VPL-HW15)
chassis (VPL-HW15)
1-8
VPL-HW10
1-3-7. C Board-2 and U Board
Note in operation:
Do not damage the harnesses.
Do not damage the harnesses.
5
Four screws
(PSW M4
x
16)
2
Four screws
(BVTP 3
x
12)
8
Screw
(BVTP 3
x
12)
4
Front cover assembly
7
Optical unit block (C board)
6
Two dowels
1
Lens cap
3
HD sticker
9
U board
CN70
Lead with connector (LVDS)
GA board
Marking is printed on the top.
QA board
CN900
Front Side
of Unit
of Unit
Claw of plate clamp
G board holder block
When installing the harness,
the harness should not protrude
exceeding the shaded area.
the harness should not protrude
exceeding the shaded area.
When installing the harness,
place the harness at a right angle.
place the harness at a right angle.
Claw of bottom cover
CN401
CN602
CN605
CN300
CN300
Tape
Chassis
Harness of the lead with connector
(LVDS) should not override on top
of the chassis screw.
(LVDS) should not override on top
of the chassis screw.
Chassis screw
Lead with connector
(LVDS)
(LVDS)
1-9
VPL-HW10
1-3-8. C Board-3
2
Six screws
(PSW M3
x
8)
4
Six screws
(PSW M3
x
8)
6
Screw
(PSW M3
x
8)
1
Two EMC tapes (25)
9
C sheet (CU)
3
C board cover
5
C board
CN700
CN500
CN600
8
Remove the C board
holder assembly in the
direction of the arrow
direction of the arrow
A
.
7
Open the three gasket
holder assemblies.
A
Be careful not to drop
the three EMC clips.
the three EMC clips.
1-3-9. Optical Unit Assembly
1
Screw
(PSW M3
x
8)
7
Screw
(PSW M4
x
16)
3
Two screws
(PSW M3
x
8)
4
HB board,
LED bracket
8
Optics attachment
5
Loosen three screws.
6
Lamp block assembly
2
TL board
![
Optical unit assembly
!=
Zoom ring assembly
!-
Focus ring assembly
9
Three tapping
screws (1.7
x
4)
0
Three tapping
screws (1.7
x
4)
1-10
VPL-HW10
1-3-10. D.C. Fan
5
Two dowels
4
GND wire
harness
6
Remove the D.C. fan block
in the direction of the arrow
B
.
3
Three screws
(BVTP 3
x
12)
7
Two screws
(BVTP 3
x
12)
9
Fan cover
0
Six claws
!]
D.C. fan
!=
Fan bracket
(F) (CH)
!-
Fan bracket
(R) (CH)
![
Eight fan dampers
8
Two claws
B
Rear Side
of Unit
of Unit
Two fan harnesses
2
Claw
1
Remove the lamp power connector
assembly in the direction
of the arrow
of the arrow
A
.
A
Claw
Chassis
Lamp power connector
assembly
assembly
Lamp power connector
assembly
assembly
C board
Bottom cover assembly
D.C. fan block
When installing the GND wire harness,
route it while giving tension on it, in a remote
location away from the C board as shown.
route it while giving tension on it, in a remote
location away from the C board as shown.
Rear Side
of Unit
of Unit
GND wire harness
VPL-HW10 only
Label side
Click on the first or last page to see other RM-PJAW15 / RM-PJHW15J / RM-PJVW70 / VPL-HW10 / VPL-HW15 service manuals if exist.