DOWNLOAD Sony HDR-TD20 / HDR-TD20E / HDR-TD20V / HDR-TD20VE (serv.man2) Service Manual ↓ Size: 6.97 MB | Pages: 32 in PDF or view online for FREE

HDR-TD20/TD20E/TD20V/TD20VE_L2

1-5

C5525

C5526

C5527

C5528

C5529

R5506

C5530

C5531

C5532

IC5501

about 330 msec

Note: The length of low section will vary a little depending on the conditions.

Order

Procedure

1

Turn the power OFF.

2

While measuring with an oscilloscope the output voltage of R5506 in the periphery of IC5501 on the VC-655 board, turn the 
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.

3

If the output voltage change as shown in Fig. 2, replace the lens device (Note). If it does not change as shown in Fig. 2, inspect 
the camera control circuit (IC1601 of VC-655 board) periphery.

Note:  When the lens device was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.

After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.

Order

AdjustBlock

AdjustCode

Order

1

If a caution occurs only in the 2D mode, perform the procedure beginning with step 6.

2

Start the Adjust Manual in the Adjust Station and execute the [Measure to E:62:11/12 for 2D] on the 
[SERVICE] tab in the 3D mode.

3

Check if the shift lens moves while setting the order 2.
If the shift lens does not move, replace the lens device (Note).
When the shift lens moved, proceed to the order 4.

4

While setting the order 1, measure with an oscilloscope the output voltage of C5529 and C5530 in 
the periphery of IC5501 on the VC-655 board to check the output voltage varies.

5

If the output voltage does not vary, replace the lens device (Note).
When the output voltage varied, proceed to the order 6.

6

Start the Adjust Manual in the Adjust Station and execute the [Measure to E:62:11/12 for 2D] on the 
[SERVICE] tab in the 2D mode.

7

Check if the shift lens moves while setting the order 6.
If the shift lens does not move, replace the lens device (Note).
When the shift lens moved, proceed to the order 8.

8

While setting the order 1, measure with an oscilloscope the output voltage of C5525 and C5526 in 
the periphery of IC5501 on the VC-655 board to check the output voltage varies.

9

If the output voltage does not vary, replace the lens device (Note).
When the output voltage varied, proceed to the order 10.

10

Turn the power OFF.

11

While measuring with an oscilloscope the output voltage of R5506 in the periphery of IC5501 on the
VC-655 board, turn the power ON to check that the output voltage immediately after the power on
change as shown in Fig. 2.

12

If the output voltage change as shown in Fig. 2, replace the lens device (Note).
If it does not change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-655 board
and IC5501 of VC-655 board) periphery.

Note:  When the lens device was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
 

After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.

HDR-TD20/TD20E/TD20V/TD20VE_L2

1-6

Order

AdjustBlock

AdjustCode

Order

1

If a caution occurs only in the 2D mode, perform the procedure beginning with step 6.

2

Start the Adjust Manual in the Adjust Station and execute the [Measure to E:62:11/12 for 2D] on the 
[SERVICE] tab in the 3D mode.

3

Check if the shift lens moves while setting the order 2.
If the shift lens does not move, replace the lens device (Note).
When the shift lens moved, proceed to the order 4.

4

While setting the order 1, measure with an oscilloscope the output voltage of C5531 and C5532 in 
the periphery of IC5501 on the VC-655 board to check the output voltage varies.

5

If the output voltage does not vary, replace the lens device (Note).
When the output voltage varied, proceed to the order 6.

6

Start the Adjust Manual in the Adjust Station and execute the [Measure to E:62:11/12 for 2D] on the 
[SERVICE] tab in the 2D mode.

7

Check if the shift lens moves while setting the order 6.
If the shift lens does not move, replace the lens device (Note).
When the shift lens moved, proceed to the order 8.

8

While setting the order 1, measure with an oscilloscope the output voltage of C5527 and C5528 in 
the periphery of IC5501 on the VC-655 board to check the output voltage varies.

9

If the output voltage does not vary, replace the lens device (Note).
When the output voltage varied, proceed to the order 10.

10

Turn the power OFF.

11

While measuring with an oscilloscope the output voltage of R5506 in the periphery of IC5501 on the
VC-655 board, turn the power ON to check that the output voltage immediately after the power on
change as shown in Fig. 2.

12

If the output voltage change as shown in Fig. 2, replace the lens device (Note).
If it does not change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-655 board
and IC5501 of VC-655 board) periphery.

Note:  When the lens device was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
 

After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.

Order

Procedure

1

Turn the power ON.

2

Confirm the connections of flexible flat cables and connectors between the lens device and VC-655 board.

3

In case of no malfunction of connections, replace the lens device with new one (Note) . When the error has occurred in spite of the lens 
replacement, replace VC-655 board with new one.

Note:  When the lens device was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.

After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.

After a part of set was replaced or after the set was assembled, check the reception of GPS signal.

Bring your camcorder to an open area, and set the GPS to ON (

 appears on the LCD screen). Your camcorder starts trying to triangulate. When 

your camcorder triangulates successfully, it will record the location information at the time movies and photos were recorded. 

• The indicator changes according to the strength of GPS signal reception.

• It may take a while before the camcorder starts triangulating.

To return the display of the unit to “A message appears asking you to confirm whether you agree with the terms of the license agreement of the map
data,” make settings according to the instructions on the SERVICE tab in the Adjustment Manual.

If you import GPS Assist Data from your computer to your camcorder using the supplied software “PlayMemories Home,” the time it takes the cam-
corder to acquire your location information can be shortened.
Connect the camcorder to a computer that is connected to the Internet. The GPS Assist Data will be updated automatically.

Do not factory check MM-103 BOARD (TD20V/TD20VE) in which Map Data is installed.
The Map data is erased when the factory check is done.

This model is provided with a flash unit using LED Flash/Video light.
Therefore, the LED Flash/Video light does not have high voltage part and does not need to be discharged.

HDR-TD20/TD20E/TD20V/TD20VE_L2

1-7

The model display adopts the laser printing method.
Therefore, the Cabinet (Bottom)  for replacement differs depending on 
the destination.
As similar displays are provided, choose the suitable one for order.

Note: After replacing the Cabinet (Bottom) , the serial number for it 

will be changed to the one exclusive for service use.
Inform a customer of the serial number change and change the 
serial number in the repair data.

Part No. 

Description

A-1871-493-A  CABINET (BOTTOM (TD20))

HDR-TD20E (E Model)

Part No. 

Description

A-1871-494-A  CABINET (BOTTOM (TD20))

Part No. 

Description

A-1871-495-A  CABINET (BOTTOM (TD20))

HDR-TD20E (JE Model)

Part No. 

Description

A-1871-496-A  CABINET (BOTTOM (TD20))

HDR-TD20V (US Model)

Part No. 

Description

A-1871-484-A  CABINET (BOTTOM (TD20))

HDR-TD20E (NE Model)

Part No. 

Description

A-1889-554-A  CABINET (BOTTOM (TD20))

HDR-TD20V (CND Model)

Part No. 

Description

A-1871-485-A  CABINET (BOTTOM (TD20))

HDR-TD20V (E Model)

Part No. 

Description

A-1871-486-A  CABINET (BOTTOM (TD20))

HDR-TD20V (J Model)

Part No. 

Description

A-1871-483-A  CABINET (BOTTOM (TD20))

HDR-TD20VE (AEP Model)

Part No. 

Description

A-1871-487-A  CABINET (BOTTOM (TD20))

HDR-TD20VE (E Model)

Part No. 

Description

A-1871-490-A  CABINET (BOTTOM (TD20))

HDR-TD20VE (UK Model)

Part No. 

Description

A-1871-488-A  CABINET (BOTTOM (TD20))

HDR-TD20VE (NE Model)

HDR-TD20VE (AUS Model)

Part No. 

Description

A-1871-489-A  CABINET (BOTTOM (TD20))

HDR-TD20VE (HK Model)

Part No. 

Description

A-1871-491-A  CABINET (BOTTOM (TD20))

Part No. 

Description

A-1871-492-A  CABINET (BOTTOM (TD20))

HDR-TD20E (CH Model)

HDR-TD20 (KR Model)

Serial No.

Serial No.

Serial No.

Serial No.

Serial No.

Serial No.

Serial No.

Serial No.

Serial No.

Serial No.

Serial No.

Serial No.

Serial No.

Serial No.

Serial No.

The year of manufacture on the labels should be the same as the previous Cabinet (Bottom)  (circled portions shown on the below).
Example: For the figure below, attach the “Made of 11 years” label.

* No label is supplied with the Cabinet (bottom) for service. Labels are supplied individually.
  If you need labels, place an order for 4-424-330-01.

HDR-20V (J Model)

* Manufacturing year

* 

Affix the label

 

The date of manufacture on the labels should be the same as the previous Cabinet (Bottom)  (circled portions shown on the below).
Example: For the figure below, attach the “1A” labels.

* No label is supplied with the Cabinet (bottom) for service. Labels are supplied individually.
  If you need labels, place an order for 4-415-879-01.

HDR-20V (US Model)

* Manufacturing year

* 

Affix the label

 

The date of manufacture on the labels should be the same as the previous Cabinet (Bottom)  (circled portions shown on the below).
Example: For the figure below, attach the “2011-01” label.

* No label is supplied with the Cabinet (bottom) for service. Labels are supplied individually.
  If you need labels, place an order for 4-424-330-01.

HDR-20 (KR Model)

* Manufacturing year

* 

Affix the label

 

HDR-TD20/TD20E/TD20V/TD20VE_L2

1-8

[Auto 3D Lens Adjust] procedure
Object to be displayed on the LED during [Auto 3D Lens Adjust]
Distance from the object and zoom rate at the time of 3D shooting
3D movie shooting method while checking 2D movie (for long-time shooting)
Connection method when playing 3D movie on the 3DTV

Use the demonstration movie as 3D data reference movie.

[3D Depth Adjustment] method
Adjustment of stereoscopic effect during playback of movie (on the touch panel)
Adjustment of stereoscopic effect of image displayed on the screen at shooting 
(with the MANUAL dial)

1 

2 

3 

When "3D effect cannot be verified on 

the LCD panel" is indicated from a user.

Play the demonstration movie and check it 

on the LCD panel.

  2

Notify the user of the content ( 

1

) when 

sending back the unit.

= Repair content =
After the user's unit has been repaired, 
check operation with the user's unit and the 
normally operating unit by comparison.

   Test preview
   (Shoot an identical object in the same 
    environment.)
   Check playback operation on the LCD 
   panel.
   (Use the demonstration movie.)
   Check playback operation on the 3DTV.
   (Use the demonstration movie.)

Play the demonstration movie and check it 

on the 3DTV.

  2

Notify the user that there is no problem with 

the product.

Explanation of shooting method and movie 

playback method. (in accordance with the 

description in the instruction manual)

  1

End

Receive the unit for repair.

Perform Light Ray

Performance Check in from 

the Adjust manual.

Explain how to make 3D 

Depth Adjustment to the user.

(in accordance with the description 

in the instruction manual)

  3

Play the demonstration

movie with the user's unit and 

the normally operating unit, and check 

whether the user can view 

3D movie.

  2

NG

NG

NG

OK

OK

OK

 

1-1.  修理時の電源供給について

本機では，安定化電源（8.4Vdc）からバッテリ端子に電源を供給した場合，約10秒後にシャットオフし，動作しなくなります。
これを避けるため，下記の方法を用いてください。

方法：

ACアダプタを使用する。

1-2.  VC-655基板交換時の注意

基板交換時は，下記の点に注意してください。

仕向けデータ

補修用基板と交換する時，補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。
Adjust StationからAdjust Manualを起動させて「DESTINATION DATA WRITE」を実行させてください。
補修用基板交換後、電源を入れると内蔵記録メディアエラーが表示される場合がありますが、「DESTINATION  DATA  WRITE」を実行
させると消えます。「DESTINATION DATA WRITE」実行しても消えない場合は、内蔵記録メディアをフォーマットしてください。

USBシリアルセーブ

補修用基板と交換する時，交換前の基板よりUSBシリアルNo.を取得してください。
データの取得はAdjust StationからAdjust Manualを起動させて「USB SERIAL SAVE」を実行させてください。

USBシリアルNo.

セットは，1台毎に異なる固有のID（USB Serial No.）を書き込んだ後，出荷されています。
新品の補修用基板には，このIDが書き込まれていないので，基板交換後にIDを入力する必要があります。
Adjust StationからAdjust Manualを起動させて「USB SERIAL No. INPUT」を実行させてください。

内蔵メモリー搭載機について

補修用基板に交換後は，最初に下記の手順を実行してください。
1.  Adjust ManualのADJUSTタブにある，「DESTINATION DATA WRITE」を実行する。
2.  下記のスクリプトファイルを実行する。
 

・  11DdmMmcReadTestMINI_v4.vbe

 

・  11DdmMmcMakePartition_v4.vbe

  スクリプトファイルはTISSホームページより入手してください。

 

TISSホームページで検索する際はPart Number欄に

「IM_VC_TOOL」

と入力して検索してください。

このスクリプトファイルを実行しなかった場合，以下のような症状が発生する可能性があります。
必ず上記のスクリプトを実行してください。

・  内蔵メモリーがメディアとして認識できない
・  内蔵メモリー内に保存されている，管理ファイルの修復ができない
・  内蔵メモリーのフォーマットができない