Sony HDR-HC1 / HDR-HC1E / HDR-HC1EK / HDR-HC1K (serv.man2) Service Manual ▷ View online
2-1
2. DISASSEMBLY
2. DISSASSEMBLY
HDR-HC1/HC1E/HC1K/HC1EK_L2
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, dont’ pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, dont’ press down at wire of connector.
It is possible that a wire is snapped.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
DISCHARGING OF THE FP-284 FLEXIBLE BOARD’S CHARGING CAPACITOR
(C901, C902)
(C901, C902)
The charging capacitor (C901, C902) of the FP-284 flexible board
is charged up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
is charged up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k
a resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
prevent electrical shock.
1 k
Ω
/1 W
Wrap insulating tape.
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between the two points
with the short jig about 10 seconds.
Short-circuit between the two points
with the short jig about 10 seconds.
R:1 k
Ω
/1 W
(Part code:
1-215-869-11)
1-215-869-11)
NOTE FOR DISCONNECTING THE HARNESS (COAXIAL CABLE)
Tweezers etc.
Harness (coaxial cable)
When disconnecting the harness (coaxial cable), do not pull the
harness part but pull off the connector body with tweezers etc.
harness part but pull off the connector body with tweezers etc.
HDR-HC1/HC1E/HC1K/HC1EK_L2
2. DISASSEMBLY
2-3
2-4
The following flow chart shows the disassembly procedure.
2-1. DISASSEMBLY
HELP
HELP
to Page 2-5
1
Open the LCD.
2
Screw (M1.7x4) (black/silver)
x1
3
Lifting up the EVF lens block.
4
Screw (M1.7x2.5) (black)
x1
5
Screw (M1.7x4) (black/silver)
x3
6
Turn down the EVF lens block.
7
Claw
x1
8
Cabinet (upper) block
1
Screw (M1.7x2.5) (black/silver)
x2
2
Claw
x2
3
P cabinet (C) assembly
4
Flexible board
x5
5
P2 lock ace screw
(M1.7x2.5) (silver)
(M1.7x2.5) (silver)
x1
6
PP-001 board
7
P2 lock ace screw
(M1.7x2.5) (silver)
(M1.7x2.5) (silver)
x2
8
Panel frame
9
Panel insulating sheet
0
D9001, LCD9001
qa
Panel cushion
1
Tape (A)
x1
2
Screw (M1.7x4) (black)
x2
3
Flexible board
x1
4
Battery panel block
5
7
8
2
1
3
6
4
5
5
1
Screw (M1.7x2.5)
(black/silver)
(black/silver)
x2
2
Screw (M1.7x4) (black)
x6
3
Open the flash unit.
4
Screw (M1.7x2.5) (black)
x2
5
Open the jack
cover (rear).
cover (rear).
6
Screw (M1.7x4) (black)
x1
7
Screw (M1.7x4)
(black/silver)
(black/silver)
x1
8
Remove the cabinet
(R) block .
(R) block .
9
Flexible board
x2
0
Cabinet (R) block
qa
Discharging the Capacitor.
6
Sheet (HS)
x1
7
Flexible board
x2
8
P2 lock ace screw
(M1.7x2.5) (silver)
(M1.7x2.5) (silver)
x1
9
OO-001 board
1
Connector
x1
2
Screw (M1.7x2.5)
(black)
(black)
x1
3
Claw
x1
4
Flexible board
x1
5
External connector
1
Screw (M1.7x2.5) (black)
x2
2
Screw (M1.7x4) (black)
x1
3
Boss
x1
4
Remove the stroboscope
block assembly.
block assembly.
5
Flexible board
x1
6
Stroboscope block assembly
1
5
2
6
7
8
9
0
qa
4
4
3
1
1
2
2
3
qa
4
4
7
5
8
9
0
6
1
3
2
4
8
6
9
7
2
3
4
5
1
7
1
4
5
6
3
2
Refer to page 2-1 " Discharging of the FP-284
flexible board's charging capacitor (C901, C902 ) ",
when discharging the capacitor.
flexible board's charging capacitor (C901, C902 ) ",
when discharging the capacitor.
HELP
Ver 1.1 2005.08
HDR-HC1/HC1E/HC1K/HC1EK_L2
2. DISASSEMBLY
2-5
2-6
from Page 2-4
1
P2 lock ace screw
(M1.7x2.5) (silver)
(M1.7x2.5) (silver)
x1
2
Claw
x1
3
Flexible board
x1
4
DC-IN connector
section
section
5
Flexible board
x4
6
Connector
x1
1
4
5
5
5
6
7
0
8
9
9
3
2
7
P2 lock ace screw
(M1.7x2.5) (silver)
(M1.7x2.5) (silver)
x2
8
Remove the TT board.
9
Flexible board
x2
0
TT board
1
Flexible board
x2
2
Flexible board
x6
3
P2 lock ace screw
(M1.7x2.5) (silver)
(M1.7x2.5) (silver)
x1
4
Hook
x3
5
NN board
1
Flexible board
x2
2
Claw
x2
3
Tape (A)
x1
4
P2 lock ace screw
(M1.7x2.5) (silver)
(M1.7x2.5) (silver)
x1
5
Lens block assembly
1
Screw (M1.7x4)
(black)
(black)
x1
2
P2 lock ace screw
(M1.7x2.5) (silver)
(M1.7x2.5) (silver)
x3
3
Screw (M1.4x1.5)
x3
4
MD frame assembly
5
Mechanism deck
1
Lifting up the lens block.
2
Screw (M1.7x2.5) (black)
x1
3
Screw (M1.7x2.5) (black)
x1
4
Screw (M1.7x2.5) (black)
x1
5
Boss
x2
6
Remove the EVF lens block.
7
Tape (A)
x1
8
Flexible board
x1
9
EVF lens block
1
2
4
5
5
6
7
8
9
3
1
1
3
2
4
5
1
2
2
2
3
4
4
4
5
1
2
3
4
5
2
HELP
Refer to page 2-1
" Note for disconnecting the harness
(coxial cable) ".
" Note for disconnecting the harness
(coxial cable) ".
HELP
HELP
Ver 1.1 2005.08
2-7
HDR-HC1/HC1E/HC1K/HC1EK_L2
2-2. THE METHOD OF ATTACHMENT OF FP-248, FP-259 FLEXIBLE BOARD
– FP-248 FLEXIBLE BOARD –
Hinge cover (rear)
FP-248 flexible board
FP-259 flexible board
Fold
Fold
Adhesive tape
Adhesive tape
Adhesive tape
A
B
Fold
1
The
A
and
A
,
B
and
B
section are united
and an angle is folded.
2
An angle is folded.
3
An angle is folded.
Fold
Fold
to Page 2-8
– FP-259 FLEXIBLE BOARD –
Click on the first or last page to see other HDR-HC1 / HDR-HC1E / HDR-HC1EK / HDR-HC1K (serv.man2) service manuals if exist.