Sony HDR-FX7 / HDR-FX7E (serv.man4) Service Manual ▷ View online
6-11
HDR-FX7/FX7E_ADJ
Address
Initial value
Remark
NTSC PAL
72 to 75
Fixed data-1 (Initialized data)
76
5C
5C
LCD automatic adj. (Contrast)
77
38
38
Contrast adj. (EVF)
78 to 84
Fixed data-1 (Initialized data)
Fixed data-1 (NTSC)/
85
−
70
S VIDEO OUT Y level adj. (PAL)
86
−
8A
87
−
61
88 to 92
Fixed data-1 (Initialized data)
93
79
79
COMPONENT OUT Y level adj.
94
31
31
COMPONENT OUT Pb level adj.
95
32
32
COMPONENT OUT Pr level adj.
96 to F3
Fixed data-1 (Initialized data)
F4
00
00
F5
00
00
F6
00
00
F7
00
00
F8
00
00
F9
00
00
FA
00
00
FB
00
00
FC
00
00
FD
00
00
FE
00
00
FF
00
00
Emergence memory address
(Mechanism section)
5.
C Page table
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Note 2:
Fixed data-1: Initialized data. (Refer to “1. Initializing
the 8, C, 13, 18, 1C Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, C, 13, 18, 1C Page Data”)
the 8, C, 13, 18, 1C Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, C, 13, 18, 1C Page Data”)
Address
Initial value
Remark
NTSC PAL
10
EE
EE
11
00
00
12
00
00
Switching position adj.
13
00
00
14, 15
Fixed data-1 (Initialized data)
16
E0
E0
CAP FG duty adj.
17 to 24
Fixed data-1 (Initialized data)
S VIDEO OUT Y level adj. (NTSC)/
25
70
−
Fixed data-1 (PAL)
26
8A
−
S VIDEO OUT chroma level adj.
27
61
−
(NTSC)/Fixed data-1 (PAL)
28 to 31
Fixed data-1 (Initialized data)
32
4D
4D
Back light adj. (EVF)
33
98
98
34
80
80
VCO adj. (EVF)
35
80
80
36
29
29
V-COM level adj. (EVF)
37
B1
B1
RGB AMP adj. (EVF)
38
Fixed data-1 (Initialized data)
39
4E
4E
PSIG level adj. (EVF)
3A
80
80
White balance adj. (EVF)
3B
80
80
3C
38
38
Contrast adj. (EVF)
3D to 3F
Fixed data-1 (Initialized data)
40
Fixed data-2
41
Fixed data-1 (Initialized data)
42
Fixed data-2
43, 44
Fixed data-1 (Initialized data)
45
8C
8C
LCD automatic adj. (VCO)
46
AA
AA
47
BC
BC
V-COM adj. (LCD)
48 to 4A
Fixed data-1 (Initialized data)
4B
79
79
Transmissive mode white balance adj.
4C
7D
7D
(LCD)
4D
5C
5C
LCD automatic adj. (Contrast)
4E to 51
Fixed data-1 (Initialized data)
52
Fixed data-2
53
Fixed data-1 (Initialized data)
54
9F
9F
Sample hold phase adj. (LCD)
55 to 6D
Fixed data-1 (Initialized data)
6E
6F
Fixed data-2
70
8E
8E
Reflective mode white balance adj.
71
87
87
(LCD)
Fixed data-1 (NTSC)/
S VIDEO OUT chroma level adj.
(PAL)
6-12
HDR-FX7/FX7E_ADJ
6.
13 Page table
Note 1:
If reading/writing data on pages 13, set data: 01 to page:
0, address: 10, and then select pages: 3. By this data set-
ting, the pages 13 can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
0, address: 10, and then select pages: 3. By this data set-
ting, the pages 13 can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Note 2:
Fixed data-1: Initialized data. (Refer to “1. Initializing
the 8, C, 13, 18, 1C Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, C, 13, 18, 1C Page Data”)
the 8, C, 13, 18, 1C Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, C, 13, 18, 1C Page Data”)
Address
Initial value
Remark
NTSC PAL
00 to 03
Fixed data-1 (Initialized data)
04
08
08
05
00
00
06
46
46
07
01
01
08
02
02
Node unique ID No. input
09
00
00
0A
00
00
0B
00
00
0C to 12
Fixed data-1 (Initialized data)
13
Fixed data-2
14 to 23
Fixed data-1 (Initialized data)
24
25
Fixed data-2
26 to 98
Fixed data-1 (Initialized data)
99
Fixed data-2
9A to FF
Fixed data-1 (Initialized data)
8.
1C Page table
Note 1:
If reading/writing data on pages 1C, set data: 01 to page:
0, address: 10, and then select pages: C. By this data set-
ting, the pages 1C can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to“00”.
0, address: 10, and then select pages: C. By this data set-
ting, the pages 1C can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to“00”.
Note 2:
Fixed data-1: Initialized data. (Refer to “1. Initializing
the 8, C, 13, 18, 1C Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, C, 13, 18, 1C Page Data”)
the 8, C, 13, 18, 1C Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, C, 13, 18, 1C Page Data”)
Address
Initial value
Remark
NTSC PAL
00 to B2
Fixed data-1 (Initialized data)
B3
00
00
B4
00
00
B5
00
00
B6
00
00
B7
00
00
B8
80
80
B9
00
00
BA
00
00
BB
00
00
BC
00
00
BD
00
00
BE
00
00
Error rate check
BF
00
00
C0
00
00
C1
00
00
C2
00
00
C3
80
80
C4
00
00
C5
00
00
C6
00
00
C7
00
00
C8
00
00
C9 to FF
Fixed data-1 (Initialized data)
7.
18 Page table
Note 1:
If reading/writing data on pages 18, set data: 01 to page:
0, address: 10, and then select pages: 8. By this data set-
ting, the pages 18 can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
0, address: 10, and then select pages: 8. By this data set-
ting, the pages 18 can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Note 2:
Fixed data-1: Initialized data. (Refer to “1. Initializing
the 8, C, 13, 18, 1C Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, C, 13, 18, 1C Page Data”)
the 8, C, 13, 18, 1C Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, C, 13, 18, 1C Page Data”)
Address
Initial value
Remark
NTSC PAL
00 to 6E
Fixed data-1 (Initialized data)
6F
70
Fixed data-2
71 to FF
Fixed data-1 (Initialized data)
9.
1D Page table
Note 1:
If reading/writing data on pages 1D, set data: 01 to page:
0, address: 10, and then select pages: D. By this data
setting, the pages 1D can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
0, address: 10, and then select pages: D. By this data
setting, the pages 1D can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Note 2:
Fixed data-1: Initialized data. (Refer to “1. Initializing
the 8, 9, C, 13, 18, 1C, 1D Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, 9, C, 13, 18, 1C, 1D Page Data”)
the 8, 9, C, 13, 18, 1C, 1D Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, 9, C, 13, 18, 1C, 1D Page Data”)
Address
Initial value
Remark
NTSC PAL
00 to FF
Fixed data-1 (Initialized data
6-13
HDR-FX7/FX7E_ADJ
1-2-3.
Initialization of Camera Control Page Data
1.
Initializing of Camera Control Page Data
Note 1:
If “Initialization of Camera Control Page Data” is ex-
ecuted, all data on camera control page are initialized.
(Only an individual page cannot be initialized)
ecuted, all data on camera control page are initialized.
(Only an individual page cannot be initialized)
Note 2:
If the camera control page data has been initialized, the
following adjustments need to be performed again.
1) Modification of camera control page data
2) Camera system adjustment (if all areas were initial-
following adjustments need to be performed again.
1) Modification of camera control page data
2) Camera system adjustment (if all areas were initial-
ized)
Adjustment Page
6D
Adjustment Address
00 to F9
Adjustment Page
6E
Adjustment Address
00 to FF
Adjustment Page
6F
Adjustment Address
10 to FF
Adjustment Page
7B
Adjustment Address
00 to 4F
Adjustment Page
8D
Adjustment Address
00 to FF
Adjustment Page
8E
Adjustment Address
00 to FF
Adjustment Page
8F
Adjustment Address
00 to FF
Adjustment Page
9D
Adjustment Address
00 to 4F
Adjustment Page
9E
Adjustment Address
00 to FF
Adjustment Page
9F
Adjustment Address
00 to F3
Adjustment Page
AD
Adjustment Address
00, 01
Adjustment Page
AE
Adjustment Address
00 to 8F
Adjustment Page
AF
Adjustment Address
00 to FF
Adjustment Page
BE
Adjustment Address
00 to FF
Adjustment Page
BF
Adjustment Address
00 to FF
Adjustment Page
C2
Adjustment Address
00 to FF
Adjustment Page
C3
Adjustment Address
00 to FF
Adjustment Page
C4
Adjustment Address
00 to FF
Adjustment Page
C5
Adjustment Address
00 to FF
Adjustment Page
C6
Adjustment Address
00 to DF
Adjustment Page
CC
Adjustment Address
00 to FF
Initializing method:
Order Page Address Data
Procedure
1
0
01
01
2
0
10
00
3
6
01
Set the following data, and
press PAUSE (Write) button.
(Note 3)
press PAUSE (Write) button.
(Note 3)
NTSC model:
2D: Initializing all areas
31: Initializing other than
adjustment address
adjustment address
PAL model
2F: Initializing all areas
33: Initializing other than
adjustment address
adjustment address
4
6
03
01
Press PAUSE (Write) button.
5
6
02
Check the data changes to
“01”.
“01”.
6
6
01
00
Press PAUSE (Write) button.
7
Perform “Modification of
Camera Control Data”.
Camera Control Data”.
Note 3:
If other than adjustment address was initialized, the ad-
justed data is not initialized.
justed data is not initialized.
Adjustment Page
CD
Adjustment Address
00 to FF
Adjustment Page
CE
Adjustment Address
00 to FF
Adjustment Page
CF
Adjustment Address
00 to FF
6-14
HDR-FX7/FX7E_ADJ
2.
Modification of Camera Control Page Data
If the camera control page data has been initialized, change the
data of the “Fixed data-2” address shown in the following table by
manual input.
data of the “Fixed data-2” address shown in the following table by
manual input.
Modifying Method:
1) Before changing the data, select page: 0, address: 01, and set
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) If 2-digit page is selected, set higher-order digit to page: 0,
address: 10 as data, and then select lower-order digit by a usual
method.
e.g.: Set data: 06 to page: 0, address: 10, and then select page:
D. Thus, the page 6D can be selected.
After the modification of data finished, return the data on page:
0, address: 10 to “00”.
method.
e.g.: Set data: 06 to page: 0, address: 10, and then select page:
D. Thus, the page 6D can be selected.
After the modification of data finished, return the data on page:
0, address: 10 to “00”.
3) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note: If copy the data built in the different model, the camcorder
may not operate.
the data built in the same model.
Note: If copy the data built in the different model, the camcorder
may not operate.
4) When changing the data, press the PAUSE button of the ad-
justment remote commander each time when setting new data
to write the data in the non-volatile memory.
to write the data in the non-volatile memory.
5) If all areas were initialized, check that the data at the addresses
for adjustment are initial values (adjustment initial values)
listed in the table. If different, change them to the adjustment
initial values.
listed in the table. If different, change them to the adjustment
initial values.
Processing after Completing Modification Camera Control
Data:
Data:
Order Page Address Data
Procedure
1
0
10
00
2
2
00
29
3
2
01
29
Press PAUSE button.
3.
6D Page table
Note 1:
If reading/writing data on pages 6D, set data: 06 to page:
0, address: 10, and then select pages: D. By this data
setting, the pages 6D can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
0, address: 10, and then select pages: D. By this data
setting, the pages 6D can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Note 2:
Fixed data-1: Initialized data. (Refer to “1. Initializing
the Camera Control Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of Camera Control Data”)
the Camera Control Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of Camera Control Data”)
Address
Initial value
Remark
NTSC PAL
00
00
00
01
00
00
02
00
00
03
00
00
04
00
00
05
00
00
06
00
00
07
00
00
08
00
00
09
00
00
0A
00
00
0B
00
00
0C
00
00
0D
00
00
Differential gain adj.
0E
00
00
0F
00
00
10
00
00
11
00
00
12
00
00
13
00
00
14
00
00
15
00
00
16
00
00
17
00
00
18
00
00
19
00
00
1A
00
00
1B
00
00
1C
00
00
1D
00
00
1E to 4F
Fixed data-1 (Initialized data)
50
58
58
HALL adj.
51
76
76
52, 53
Fixed data-1 (Initialized data)
54
28
28
HALL adj.
55
D8
D8
56, 57
Fixed data-1 (Initialized data)
58
19
19
HALL adj.
59 to 5B
Fixed data-1 (Initialized data)
5C
35
35
LV standard data input
5D
00
00
Click on the first or last page to see other HDR-FX7 / HDR-FX7E (serv.man4) service manuals if exist.