Sony HDR-CX720V / HDR-CX730E / HDR-CX740E / HDR-CX740VE / HDR-CX760E / HDR-CX760V / HDR-PJ710 / HDR-PJ710V / HDR-PJ710VE / HDR-PJ720E / HDR-PJ740VE / HDR-PJ760 / HDR-PJ760E / HDR-PJ760V / HDR-PJ760VE (serv.man4) Service Manual ▷ View online
Sony Corporation
HDR-CX720V/CX730E/CX740E/CX740VE/CX760E/CX760V/PJ710/PJ710V/PJ710VE/PJ720E/PJ740VE/PJ760/PJ760E/PJ760V/PJ760VE_L2
LEVEL
2
9-834-656-81
SUPPLEMENT-1
File this supplement with the service manual.
• Change of REPAIR PARTS LIST
• Addition of SERVICE NOTE
• Addition of REPAIR PARTS LIST
• Addition of SERVICE NOTE
• Addition of REPAIR PARTS LIST
(12-176)
SERVICE MANUAL
Ver. 1.3 2012.08
2012H08-1
© 2012.08
Published by Sony Techno Create Corporation
2. REPAIR PARTS LIST
2-1. EXPLODED VIEWS
-
: Points changed portion
Page
Former
New
2-7
2-1-5. LENS SECTION
Refer to "Caution for Handling
the Lens Device (LSV-1550A)"
the Lens Device (LSV-1550A)"
#12
6
202
201
(Note 3)
3
Cabine
(Non Pr
(Non Pr
2-1-5. LENS SECTION
Refer to "Caution for Handling
the Lens Device (LSV-1550A)"
the Lens Device (LSV-1550A)"
#1
6
202
201
(Note 3)
3
Cabine
(Non P
(Non P
(Lens Block Section
(See page 12 (Supplement-1))
)
– ENGLISH –
Some parts included in the lens unit used in this model have been added as independent replacement parts.
When replacing such parts, perform disassembling and reassembling according to SERVICE NOTE.
When replacing such parts, perform disassembling and reassembling according to SERVICE NOTE.
– JAPANESE –
このモデルで使用されているレンズユニットに含まれる部品で、単体で交換対象部品として追加されたものがあります。
交換する際は、SERVICE NOTE を参照し、分解組立作業を行ってください。
交換する際は、SERVICE NOTE を参照し、分解組立作業を行ってください。
HDR-CX720V/CX730E/CX740E/CX740VE/CX760E/CX760V/
PJ710/PJ710V/PJ710VE/PJ720E/PJ740VE/PJ760/PJ760E/
PJ760V/PJ760VE
US Model
Canadian Model
AEP Model
UK Model
North European Model
E Model
Australian Model
Hong Kong Model
Chinese Model
Korea Model
Tourist Model
Japanese Model
– 2 –
HDR-CX720V/CX730E/CX740E/CX740VE/CX760E/CX760V/PJ710/PJ710V/PJ710VE/PJ720E/PJ740VE/PJ760/PJ760E/PJ760V/PJ760VE_L2
SERVICE NOTE
FRONT ORNAMENT REPLACING METHOD
Lens Cap
A protective Lens Cap is attached to each new
service Lens Block.
Carry out replacement work with this Lens Cap
attached.
service Lens Block.
Carry out replacement work with this Lens Cap
attached.
Note:
Removal
Adhesive Parts
Adhesive Part
Connectors
Flexible Board
of the Motor A
of the Motor A
LF-148 Flexible Board
(1) Disconnect the two connectors and peel off the Adhesive
Parts of the Flexible Board of the Motor A and LF-148 Flexible
Board.
Board.
TO
P
FRON
T
Adhesive Part
Screw
Screw
Screw
Screw
Screw
Screw
Sheet Metal (C),
Edge of Mechanical Rubber
Edge of Mechanical Rubber
Bosses
Bosses
LF-153 Flexible Board
(2) Remove the six screws and remove the Sheet Metal (C),
Edge of Mechanical Rubber while detaching the four bosses.
(3) Peel off the Adhesive Parts of the LF-153 Flexible Board.
TO
P
TO
P
FRONT
FRO
NT
Screw
Screw
Screw
Screw
Screw
Plate of the
Motor B
Motor B
Screws
Frame (F-Sub-A),
Frame (F-Sub-B),
Ball Bearing
Frame (F-Sub-B),
Ball Bearing
Motor B
Shaft
Bosses
(4) Remove the two screws and remove the Frame (F-Sub-A),
Frame (F-Sub-B), and Ball Bearing while detaching the two
bosses and the shaft.
bosses and the shaft.
(5) Remove the screw and turn the Plate of the Motor B to remove
the two screws to detach the Motor B.
TO
P
FRONT
TO
P
FRONT
Screw
Screw
Screw
Screw
Screw
Screw
Screw
Sheet Metal (B),
Edge of Mechanical Rubber
Edge of Mechanical Rubber
Frame (E-Sub-A),
Frame (E-Sub-B),
Ball Bearing
Frame (E-Sub-B),
Ball Bearing
Adhesive Part
Flexible Board
of the Motor A
of the Motor A
Shaft
Bosses
Bosses
(7) Peel off the Adhesive Part of the Flexible Board of Motor A.
(6) Remove the four screws and remove the Frame (E-Sub-A),
Frame (E-Sub-B), and Ball Bearing while detaching the
four bosses and the shaft.
four bosses and the shaft.
(8) Remove the three screws to detach the Sheet Metal (B),
Edge of Mechanical Rubber.
TO
P
TO
P
TO
P
FR
ONT
FR
ONT
FRONT
– ENGLISH –
– 3 –
HDR-CX720V/CX730E/CX740E/CX740VE/CX760E/CX760V/PJ710/PJ710V/PJ710VE/PJ720E/PJ740VE/PJ760/PJ760E/PJ760V/PJ760VE_L2
Screw
Screw
Screw
Screw
Screw
Screw
Plate of the Motor A
(9) Remove the three screws while turning the Plate of the
Motor A to detach the Motor A.
Motor A
TO
P
FRONT
Screw
Polyimide Sheet
Polyimide Sheet
Screw
Screw
Screw
CM Radiation Sheet
LF-153 Flexible Board
(10) Peel off the Adhesive Part of the LF-153 Flexible Board
and disconnect the connector to remove the LF-153 Flexible
Board.
Board.
(11) Peel off the CM Radiation Sheet and peel off the
Adhesive Parts of the LF-148 Flexible Board.
(12) Peel off the two Polyimide Sheets and remove the
four screws.
Adhesive Part
Connector
Adhesive Parts
LF-148 Flexible
Board
Board
TO
P
TO
P
TO
P
FRONT
FRONT
FRONT
Screw
Screw
Boss
Boss
Boss
Bosses
Connector
(13)
(14)
Remove the screw and remove the five bosses and disconnect
the connector to detach the Sheet Metal (D-Sub) and the
LF-148 Flexible Board.
the connector to detach the Sheet Metal (D-Sub) and the
LF-148 Flexible Board.
Remove the bond.
(15) Remove the screw to detach the Sheet Metal (A).
Bond
LF-148 Flexible Board,
Sheet Metal (D-Sub)
Sheet Metal (D-Sub)
Sheet Metal (A)
TO
P
FRONT
TO
P
FRO
NT
TO
P
FR
ONT
Front Ornament
Boss
Claw
(16) Remove the boss and the claw to detach the
Front Ornament.
TO
P
FRONT
– ENGLISH –
– 4 –
HDR-CX720V/CX730E/CX740E/CX740VE/CX760E/CX760V/PJ710/PJ710V/PJ710VE/PJ720E/PJ740VE/PJ760/PJ760E/PJ760V/PJ760VE_L2
Boss
Claw
Installation
(1) While installing the boss and the claw, install the Front
Ornament.
Screw
(2)
Install the Sheet Metal (A) and tighten a screw.
Tightening torque = 0.12 ± 0.01N · m (1.2 ± 0.1kg f · cm)
Sheet Metal (A)
Polyimide Sheet
(3)
Cut the Polyimide Sheet to the specified length and stick it.
7.0mm
5.0mm
Front Ornament
TO
P
FRONT
TOP
FR
ONT
TO
P
FRO
NT
(4)
Connect the connector and install the Sheet Metal (D-Sub) and the
LF-148 Flexible Board while attaching the five bosses, and then
tighten a screw.
LF-148 Flexible Board while attaching the five bosses, and then
tighten a screw.
Tightening torque = 0.18 ± 0.01N · m (1.8 ± 0.1kg f · cm)
Note: Check that the boss with the mark is completely engaged.
Screw
Boss
Boss
Boss
Boss
Boss
Connector
LF-148 Flexible Board,
Sheet Metal (D-Sub)
Sheet Metal (D-Sub)
Sheet Metal (D-Sub)
LF-148 Flexible Board
LF-148 Flexible Board
TO
P
FRONT
Adhesive
Sheet
Sheet
If the adhesive force is lowered, cut the Adhesive Sheet as
shown in the figure in the frame and then stick it.
shown in the figure in the frame and then stick it.
Adhesive Part
Shape and sticking
position of Adhesive
Sheet
position of Adhesive
Sheet
Screw (A)
Polyimide Sheet
Polyimide Sheet
Screw (A)
Screw (B)
Screw (B)
(5)
Tighten four screws in the order shown in the figure below.
Stick the two Polyimide Sheets.
Screw (A)
Tightening torque = 0.12 ± 0.01N · m (1.2 ± 0.1kg f · cm)
Screw (B)
Tightening torque = 0.18 ± 0.01N · m (1.8 ± 0.1kg f · cm)
Tightening torque = 0.12 ± 0.01N · m (1.2 ± 0.1kg f · cm)
Screw (B)
Tightening torque = 0.18 ± 0.01N · m (1.8 ± 0.1kg f · cm)
1
2
3
4
TOP
FRONT
Bosses
Bosses
CM Radiation Sheet
(6)
Stick the LF-148 Flexible Board and then stick the CM Radiation
Sheet.
Sheet.
When sticking the LF-148 Flexible Board, position it at
the four boss holes and stick the Flexible Board while
pressing it in the arrow direction shown in the figure.
the four boss holes and stick the Flexible Board while
pressing it in the arrow direction shown in the figure.
Adhesive Parts
LF-148 Flexible
Board
Board
LF-148 Flexible
Board
Board
TO
P
FRON
T
If the adhesive force is lowered, cut the Adhesive Sheet
as shown in the figure in the frame and then stick it.
as shown in the figure in the frame and then stick it.
Shape and sticking position
of Adhesive Sheet
of Adhesive Sheet
LF-148 Flexible Board sticking direction and
boss positions
boss positions
Adhesive
Sheets
Sheets
– ENGLISH –