DOWNLOAD Sony HDR-CX405 / HDR-CX440 / HDR-PJ410 / HDR-PJ440 Service Manual ↓ Size: 3.91 MB | Pages: 62 in PDF or view online for FREE

This manual describes the information items that premise the service based on the components parts assuming use of
system and service engineers.

Besides this manual, the following manuals are available.

• Operating Guide (Supplied with this unit)
• Help Guide (Web manual)

Help Guide is an on-line manual.
Refer to it for in-depth instructions on the many functions of the camcorder.

• Adjust Manual (Available on request)

The adjustment software is necessary for adjustment and various checking of this unit for the service.

HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440

3

If an error occurs in this unit, the self-diagnosis function starts working and a code consisting of one alphabet and a four-
digit number appears on the LCD. Classification of persons in charge, classification of faulty blocks, and details of errors
can be checked by referring to this indication of five alphanumeric characters in the self-diagnosis code table.
The history of past errors can be checked in “Usage and Diag record” on the DATA tab of the Adjust Manual.
The self-diagnosis function is also described in the operation manual.

The boards and functions used in this model are mentioned in the following table.

CM board

Imager

MM board

Internal memory

WF board

Wireless LAN module

PJ board

Projector

VC board

CPU, Power, Lens drive, 3-axis angular velocity sensor, Other function

Repaired by:

Block
Function

Detailed
Code

C

0 4

0 0

Non-standard battery is used.

Use the InfoLITHIUM battery.

C

0 6

0 0

The battery pack temperature is
high.

Change the battery pack or place it in a cool place.

C

1 3

0 1

Memory card is unformatted or
memory card is broken.

Format the memory card.
Insert a new memory card.

C

1 3

0 2 

*1

Access error

Remove the power source. Reconnect it again and operate
the unit again.

C

1 3

0 3 

*1

Access error (External media)

Turn power off and turn power on again.

C

1 3

0 4 

*1

Abnormality of the drive (External
media)

Turn power off and turn power on again.

C

3 2

6 0

Difficult to adjust focus
(Cannot initialize focus)

Turn power off and turn power on again. When this error is
not cleared, the focus control signal for the lens block may
be faulty.
Check whether this error is due to the lens or the board.
Replace the faulty lens or board.

E

2 0

0 0

Flash memory data are rewritten.

Make flash memory data correct value. 

*2

E

3 1

0 0 

*1

Abnormality of the drive

Turn power off and turn power on again.

*1:

Function of this code is not provided in this unit.

*2:

Start the Adjust Manual in the Adjust Station and execute the “Destination data write” on the ADJUST tab.

HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440

1-1

Repaired by:

Block
Function

Detailed
Code

E

4 1

0 0

Abnormality of the wireless LAN
module or CPU

The peripheral circuit of between CPU and wireless LAN
module may be faulty.
Replace the board that contains this peripheral circuit.

E

6 1

0 0

Difficult to adjust focus
(Cannot initialize focus)

Turn power off and turn power on again. When this error is
not cleared, the focus control signal for the lens block may
be faulty.
Check whether this error is due to the lens or the board.
Replace the faulty lens or board.

E

6 1

1 0

Zoom operations fault
(Cannot initialize zoom lens)

Turn power off and turn power on again. When this error is
not cleared, operate the zoom lever and check following
items.

• When zooming is performed, the zoom control signal

for the lens block may be faulty.

• When zooming is not performed, the zoom motor

drive circuit may be faulty.

Check whether this error is due to the lens or the board.
Replace the faulty lens or board.

E

6 1

1 1

Focus or zoom fault

Check both C: 32: 60 and E: 61: 10 of the self-diagnosis
code.

E

6 1

3 0

Reset position detection error on the
stepper iris initializing

Turn the power on to open lens barrier. Disconnect the bat-
tery or power cord, and then connect again. And confirm
that the iris blades in lens are working.
If iris blades do not working, check the iris motor drive cir-
cuit in lens drive block. If iris blades work normally, con-
firm that they are closing completely and confirm following
items.

• Case of the iris blades do not close normally. Replace

the lens block.

• Case of “E: 61: 30” is appeared and iris blades closed

completely. Confirm that communication with lens
block is normal.

• Case of LCD is not displayed normally, check that

connection between imager board and main board.

• Case of LCD is displayed normally, replace the lens

block.

E

6 1

3 1

Error in detection of the Reset Posi-
tion at the time of Stepper IR Filter
initialization

Check the signal line connection between the lens block and
the lens control circuit.
Check whether this error is due to the lens or the board.
Replace the faulty lens or board.

E

6 2

0 0

Steadyshot does not work well.
(With PITCH angular velocity sen-
sor output stopped)

The peripheral circuit of the PITCH angular velocity sensor
may be faulty.
Replace the board that contains this peripheral circuit.

E

6 2

0 1

Steadyshot does not work well.
(With YAW angular velocity sensor
output stopped)

The peripheral circuit of the YAW angular velocity sensor
may be faulty.
Replace the board that contains this peripheral circuit.

E

6 2

0 2

Abnormality of IC for steadyshot.

Check signal line connections from CPU through steady-
shot IC to PITCH/YAW drive.
When there is no problem with the connections, replace the
board that contains this peripheral circuit.

E

6 2

0 3

Communication error of steadyshot
IC and CPU

The steadyshot circuit may be faulty.
Replace the board that contains this peripheral circuit.

E

6 2

0 4

Image vibration correction during
steadyshot does not work.

The image vibration angular velocity sensor (ROLL SEN-
SOR) peripheral circuit may be faulty.
Replace the board that contains this peripheral circuit.

HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440

1-2