DOWNLOAD Sony HDR-CX405 / HDR-CX440 / HDR-PJ410 / HDR-PJ440 Service Manual ↓ Size: 3.91 MB | Pages: 62 in PDF or view online for FREE

Repaired by:

Block
Function

Detailed
Code

E

6 2

1 0

Shift lens initializing failure

Replacement of lens block. 

*1

If an error occurs again, steadyshot circuit may be faulty.
Replace the board that contains this peripheral circuit.

E

6 2

1 1

Shift lens overheating (PITCH)

Check signal line connections from CPU through steady-
shot IC to PITCH/YAW drive.
When there is no problem with the connections, check
whether this error is due to the lens or the board. Replace
the faulty lens or board.

E

6 2

1 2

Shift lens overheating (YAW)

Check signal line connections from CPU through steady-
shot IC to PITCH/YAW drive.
When there is no problem with the connections, check
whether this error is due to the lens or the board. Replace
the faulty lens or board.

E

6 2

2 0

Abnormality of thermistor

Check signal line connections from CPU through steady-
shot IC to PITCH/YAW drive.
When there is no problem with the connections, check
whether this error is due to the lens or the board. Replace
the faulty lens or board.

E

6 2

3 0

Abnormal CPU

Turn power off and turn power on again. When this error is
not cleared, replace the board that mounts the CPU.

E

9 1

0 1 

*2

Abnormality when flash is being
charged

Check or replace the LED flash/video light or charging ca-
pacitor.

E

9 1

0 2 

*2

Abnormality of LED video light

Check or replace the LED flash/video light or charging ca-
pacitor.

E

9 1

0 3 

*2

Abnormality of LED video light
Temperature detection

Check or replace the LED flash/video light or charging ca-
pacitor.

E

9 2

0 1

Battery current value goes over the
max discharge current

Confirm whether or not the symptom is occurred after re-
placing the battery. If the symptom is still occurred, replace
board.

E

9 4

0 0

Fault of writing or erasing the inter-
nal memory

The internal memory may be faulty.
Replace the board that contains this peripheral circuit.

E

9 4

0 1

Abnormality of the internal memory

The internal memory may be faulty.
Replace the board that contains this peripheral circuit.

E

9 4

0 2

BGM data error

The CPU may be faulty.
Replace the board that contains this peripheral circuit.

E

9 5

0 0 

*2

GPS hardware error

Check the signal line connection for GPS.
When there is no problem with the connections, replace the
board that contains this peripheral circuit.

E

9 5

0 1 

*2

Acceleration sensor hardware error

The acceleration sensor may be faulty.
Replace the board that contains this peripheral circuit.

E

9 5

0 2 

*2

Electronic compass hardware error
(GPS hardware error)

The peripheral circuit of the electronic compass may be
faulty.
Replace the board that contains this peripheral circuit.

E

9 6

0 0 

*2

Map area mount error

The flash memory (Internal Memory) may be faulty.
Replace the board that contains this peripheral circuit.

E

9 7

0 0

Projector hardware error

Turn power off and turn power on again. When this error is
not cleared, the peripheral circuit of the projector may be
faulty.
Replace the board that contains this peripheral circuit.

*1:

When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items. After
the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.

*2:

Function of this code is not provided in this unit.

HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440

1-3

Identify the cause of the problem (lens or VC-1023 board), and replace the faulty lens or the VC-1023 board.

Start the Adjust Manual in the Adjust Station and execute the “Measure to E:62:11/12” on the SERVICE tab.
Then confirm that the shift lens moves. If it does not move, replace the lens block.
Identify the cause of the problem (lens or VC-1023 board), and replace the faulty lens or the VC-1023 board.

Start the Adjust Manual in the Adjust Station and execute the “Measure to E:62:11/12” on the SERVICE tab.
Then confirm that the shift lens moves. If it does not move, replace the lens block.
Identify the cause of the problem (lens or VC-1023 board), and replace the faulty lens or the VC-1023 board.

Check the connection between the lens block and VC-1023 board.
Identify the cause of the problem (lens or VC-1023 board), and replace the faulty lens or the VC-1023 board.

HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440

1-4

• Make sure that the conductive side of a flexible board does not have any stain or foreign materials.
• Do not touch the conductive side of flexible boards with bare hands.
• Plug in a flexible board straight, fully into the connector until it reaches the end inside.

Flexible

Board

Flexible
Board

Connector

Connector

Reference line

Flexible
Board

Connector

Connector

Flexible

Board

Reference line

Connector

Connector

Flexible
Board

Flexible

Board

Reference line

OK 

(The flexible board was plugged in 
straight and completely)

(The flexible board was plugged in 
crooked.)

NG 

NG 

(The flexible board was not plugged in 
completely.)

• When opening the connector's holder in direction A, do not open it with excessive force.

Holder

Connector

Flexible Board

A

A

• When closing the connector's holder, press it evenly while pushing a flexible board in direction B.

Holder

Insulation side

Connector

Flexible Board

B

• Make sure that the flat cable and flexible board are not cracked or bent at the contact end.

Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)

• Do not apply excessive force to the gilded flexible board.

• The proper way to disconnect a connector is to grab the connector instead of the wires. If you pull on the wires,

they might be broken.

• The proper way to connect a connector is to grab the connector instead of the wires. If you push on the wires, they

might be broken.

HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440

2-1

Use the AC power adaptor.

HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440

2-2