Sony HDR-CX240 / HDR-CX240E / HDR-PJ240 / HDR-PJ240E / HDR-PJ270 / HDR-PJ270E / HDR-PJ275 (serv.man2) Service Manual ▷ View online
1-2
HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
1-3. CHECKING THE Wi-Fi FUNCTION (HDR-PJ275)
Perform the following procedure to check the Wi-Fi function.
Required equipment: Windows personal computer with Wi-Fi interface
1. Turn on the power of the unit.
2. Perform the following operations.
[MENU]→[Camera/Mic]→[
2. Perform the following operations.
[MENU]→[Camera/Mic]→[
Shooting Assist]→[Ctrl with Smartphone]
3. When preparation for Wi-Fi has been completed, the following screen opens and a password for Wi-Fi connection is displayed.
Ctrl with Smartphone
Operate smartphone to connect to
this device via Wi-Fi.
SSID DIRECT-XXXX:HDR-XXXX
Password XXXXXXXX
Device Name HDR-XXXX
Wi-Fi
4. Confirm on the personal computer that the unit is detected as a connectable wireless network.
5. To further confirm that the unit is connectable, connect the unit to the personal computer and double-click the “current connection”from the icon
5. To further confirm that the unit is connectable, connect the unit to the personal computer and double-click the “current connection”from the icon
displayed on the notice field, make sure that the unit is displayed in the Wireless internet access column.
1-4. SELF-DIAGNOSIS FUNCTION
1-4-1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the Viewfinder or the LCD
screen what to do.
This function consists of two display; self-diagnosis display and service
mode display. Details of the self-diagnosis functions are provided in the
Instruction manual.
function starts working, and displays on the Viewfinder or the LCD
screen what to do.
This function consists of two display; self-diagnosis display and service
mode display. Details of the self-diagnosis functions are provided in the
Instruction manual.
1-4-2. Self-diagnosis Display
When problems occur while the unit is operating, the counter of the
Viewfinder or the LCD screen shows a 4-digit display consisting of an
alphabet and numbers, which blinks at 3.2 Hz. This 5-character display
indicates the “repaired by:”, “block” in which the problem occurred, and
“detailed code”of the problem.
Viewfinder or the LCD screen shows a 4-digit display consisting of an
alphabet and numbers, which blinks at 3.2 Hz. This 5-character display
indicates the “repaired by:”, “block” in which the problem occurred, and
“detailed code”of the problem.
0 0
3 2
C
Repaired by:
Refer to “1-4-3. Self-diagnosis Code Tabl e”.
Indicates the appropriate
step to be taken.
E.g.
13 ....
32 ....Turn on power again.
13 ....
32 ....Turn on power again.
Block
Detailed Code
Blinks at 3.2 Hz
C : Corrected by customer
E : Corrected by service
engineer
Format the “memory card”.
Viewfinder or LCD screen
1-4-3. Self-diagnosis Code Table
Self-diagnosis Code
Symptom/State
Correction
Repaired by:
Block
Function
Detailed
Code
C
0
4
0
0
Non-standard battery is used.
Use the designated battery.
C
0
6
0
0
The battery pack temperature is high.
Change the battery pack or place it in a cool place.
C
1
3
0
1
Memory card is unformatted.
Memory card is broken.
Memory card is broken.
Format the memory card.
Insert a new memory card.
Insert a new memory card.
C
1
3
0
2
Access error
Remove the power source. Reconnect it again and operate your cam-
corder again.
corder again.
C
1
3
0
3
Access error (External media)
Turn power off and turn power on again.
C
1
3
0
4
Drive fault (External media)
Turn power off and turn power on again.
C
E
3
2
6
1
6
0
0
0
Difficult to adjust focus
(Cannot initialize focus)
(Cannot initialize focus)
Retry turn the power on by the power switch. If it does not recover,
check the focus sensor of lens block (pin ek of CN4002 on the VC-
1023 board). If it is OK, check the focus motor drive IC (IC6800 on the
VC-1023 board).
check the focus sensor of lens block (pin ek of CN4002 on the VC-
1023 board). If it is OK, check the focus motor drive IC (IC6800 on the
VC-1023 board).
E
2
0
0
0
Flash memory data are rewritten.
Make flash memory data correct value. (Note 1)
E
3
1
0
0
Drive fault
Turn power off and turn power on again.
E
4
1
0
0
Wi-Fi Module Hardware Error
PJ275:
Check that connection between CN4902 on the VC-1023 board and
CN2301 on the WF-1004 board by FP-2200 flexible board.
Check that connection between CN4902 on the VC-1023 board and
CN2301 on the WF-1004 board by FP-2200 flexible board.
E
6
1
1
0
Zoom operations fault
(Cannot initialize zoom lens.)
(Cannot initialize zoom lens.)
Inspect the lens block zoom sensor (pin eg of CN4002 on the VC-1023
board when zooming is performed when the zoom lever is operated,
and the zoom motor drive circuit (IC6800 on the VC-1023 board) when
zooming is not performed.
board when zooming is performed when the zoom lever is operated,
and the zoom motor drive circuit (IC6800 on the VC-1023 board) when
zooming is not performed.
*
*
*
*
(
)
*
Note 1: Start the Adjust Manual in the Adjust Station and refer to the “DESTINATION DATA WRITE”.
Note 2: Functions of codes with * mark are not provided in this unit.
Note 2: Functions of codes with * mark are not provided in this unit.
1-3
HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
Note 2: Functions of codes with * mark are not provided in this unit.
Note 3: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
Note 3: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
Self-diagnosis Code
Symptom/State
Correction
Repaired by:
Block
Function
Detailed
Code
E
6
1
1
1
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.
E
6
1
3
0
Reset position detection error on the
stepper iris initializing
stepper iris initializing
Turn the power on to open lens barrier. Disconnect the battery or power
cord, and then connect again.
Confirm that the iris blades in lens are working.
If iris blades do not working, check the iris motor drive IC in lens drive
block (pin wg, wh of CN4002 on theVC-1023 board).
If iris blades work normally, confirm that they are closing completely
and confirm following item.
• Case of the iris blades do not close normally. Replace the lens block.
• Case of “E: 61: 30” is appeared and iris blades closed completely.
Confirm that communication with lens block is normal.
• Case of LCD is not displayed normally. Check that connection between
cord, and then connect again.
Confirm that the iris blades in lens are working.
If iris blades do not working, check the iris motor drive IC in lens drive
block (pin wg, wh of CN4002 on theVC-1023 board).
If iris blades work normally, confirm that they are closing completely
and confirm following item.
• Case of the iris blades do not close normally. Replace the lens block.
• Case of “E: 61: 30” is appeared and iris blades closed completely.
Confirm that communication with lens block is normal.
• Case of LCD is not displayed normally. Check that connection between
CN6702 on CM-1004 board and CN4004 on VC-1023 board by FP-
2190 flexible board.
2190 flexible board.
• Case of LCD is displayed normally. Replace the lens block.
E
6
2
0
0
Handshake correction function does not
work well. (With PITCH angular veloc-
ity sensor output stopped.)
work well. (With PITCH angular veloc-
ity sensor output stopped.)
E:62:00
Inspect PITCH angular velocity sensors (SE7701 on the GY-1005
board) peripheral circuits.
E:62:01
Inspect YAW angular velocity sensors (SE7701 on the GY-1005 board)
peripheral circuits.
Inspect PITCH angular velocity sensors (SE7701 on the GY-1005
board) peripheral circuits.
E:62:01
Inspect YAW angular velocity sensors (SE7701 on the GY-1005 board)
peripheral circuits.
E
6
2
0
1
Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)
work well. (With YAW angular velocity
sensor output stopped.)
E:62:00
Inspect PITCH angular velocity sensors (SE7701 on the GY-1005
board) peripheral circuits.
E:62:01
Inspect YAW angular velocity sensors (SE7701 on the GY-1005 board)
peripheral circuits.
Inspect PITCH angular velocity sensors (SE7701 on the GY-1005
board) peripheral circuits.
E:62:01
Inspect YAW angular velocity sensors (SE7701 on the GY-1005 board)
peripheral circuits.
E
6
2
0
2
Abnormality of IC for steadyshot.
Turn power off and turn power on again.
E
6
2
0
3
IC for steadyshot and micro controller
communication abnormality among.
communication abnormality among.
Inspect the steadyshot circuit (IC6800 on the VC-1023 board).
E
6
2
0
4
Image vibration correction during hand-
shake function does not work.
shake function does not work.
Inspect the image vibration angular velocity sensors (SE7711 on the
VC-1023 board) peripheral circuits.
VC-1023 board) peripheral circuits.
E
6
2
1
0
Shift lens initializing failure.
Turn power off and turn power on again.
E
6
2
1
1
Shift lens overheating (Pitch)
Turn power off and turn power on again.
E
6
2
1
2
Shift lens overheating (Yaw)
Turn power off and turn power on again.
E
6
2
2
0
Abnormality of thermistor.
Turn power off and turn power on again.
E
6
2
3
0
Abnormal CPU
Turn power off and turn power on again.
E
9
1
0
1
Abnormality when flash is being
charged.
charged.
Turn power off and turn power on again.
E
9
1
0
2
Abnormality of LED Video light.
Turn power off and turn power on again.
E
9
1
0
3
Abnormality of LED Video light Tem-
perature detection.
perature detection.
Turn power off and turn power on again.
E
9
2
0
1
Battery current value goes over the max
discharge current
discharge current
Check the remaining battery power because this symptom maybe de-
pended on the remaining battery level, and confirm whether or not the
symptom is occurred after replacing the battery. If the symptom is still
occurred, replace the VC-1023 board.
pended on the remaining battery level, and confirm whether or not the
symptom is occurred after replacing the battery. If the symptom is still
occurred, replace the VC-1023 board.
E
9
4
0
0
Fault of writing or erasing the flash
memory
memory
PJ270/PJ270E/PJ275:
Inspect the flash memory (IC8101 on the MM-102 board).
Inspect the flash memory (IC8101 on the MM-102 board).
E
9
4
0
1
Internal flash memory fault
PJ270/PJ270E/PJ275:
Inspect the flash memory (IC8101 on the MM-102 board).
Inspect the flash memory (IC8101 on the MM-102 board).
*
*
*
*
*
*
*
*
1-5. NOTE ON REPLACING PROJECTOR UNIT (Projector Model)
Refer to the following flowchart when repairing or inspecting the projector’s projection function.
If you have received an indication on the projector’s projection function from the customer, check defective part according to the following flow-
chart.
When a defective part has been clarified, repair the projector according to the check result.
chart.
When a defective part has been clarified, repair the projector according to the check result.
Note 1: The projector unit (copper plate in particular) becomes hot after it is used.
When replacing a part of the projector unit, wait until it is cooled down.
Wipe the lens gently with a soft cloth such as a cleaning cloth or glass cleaning cloth.
Note 2: Stubborn stains may be removed with a soft cloth such as a cleaning cloth or glass cleaning cloth lightly dampened with water.
Never use a solvent such as alcohol, benzene or thinner; acid, alkaline or abrasive detergent; or a chemical cleaning cloth, as they will damage the lens sur-
face.
face.
Projector problem checking procedure (other than indication on brightness)
Indicated defective
projector received
Measure brightness.
( 2)
Yes
No
OK
OK
NG
NG
OK
NG
A
B
Indication on
brightness
Inspect projector
LED.
( 1)
1 Refer to the ADJUST tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
Inspect projector
LED.
( 1)
END
-
-
-
-
-
-
-
Replace projector unit (light emitting block). (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)
Projector Data Input
Fixed value input
Enter the number on the label attached to the unit.
Serial number input
LD40
Enter the number on the label attached to the unit.
Serial number input
LD40
Syywwnnnnn
Enter the red part.
(See page 1-4)
(See page 1-4)
Self-diagnosis Code
Symptom/State
Correction
Repaired by:
Block
Function
Detailed
Code
E
9
4
0
2
BGM data error
Check the CPU (IC6000 on the VC-1023 board).
E
9
5
0
0
GPS hardware error
Turn power off and turn power on again.
E
9
6
0
0
Map area mount error
Turn power off and turn power on again.
E
9
7
0
0
Projector hardware error
Turn power off and turn power on again.
*
*
*
Note 2: Functions of codes with * mark are not provided in this unit.
HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
1-4E
Projector problem checking procedure (indication on brightness)
Yes
No
OK
NG
OK
NG
OK
NG
A
B
Indicated defective
projector received
Measure brightness.
( 2)
Measure brightness.
( 2)
Indication on
brightness
Inspect projector
LED.
( 1)
1 Refer to the ADJUST tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
END
-
-
-
-
-
-
-
Replace projector unit (light emitting block). (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)
Projector Data Input
Fixed value input
Enter the number on the label attached to the unit.
Serial number input
LD40
Enter the number on the label attached to the unit.
Serial number input
LD40
Syywwnnnnn
Enter the red part.
(See page 1-3)
(See page 1-3)
2-1
HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
2. REPAIR PARTS LIST
Follow the disassembly in the numerical order given.
IDENTIFYING PARTS
Link
ACCESSORIES
ASSEMBLY
･ Abbreviation
AUS :
AUS :
Australian
model
BR :
Brazilian
Model
CH :
Chinese
model
CND :
Canadian
model
KR :
Korea
model
NE
: North European model
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from the original
• -XX, -X mean standardized parts, so they may have some differences from the original
one.
• Items marked “*” are not stocked since they are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Due to standardization, replacements in the parts list may be different from the parts
• Due to standardization, replacements in the parts list may be different from the parts
specified in the diagrams or the components used on the set.
• CAPACITORS:
uF:
uF:
μF
• COILS
uH:
uH:
μH
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F:
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F:
nonflammable
• SEMICONDUCTORS
In each case, u: μ, for example:
uA...:
In each case, u: μ, for example:
uA...:
μA... , uPA... , μPA... ,
uPB...
,
μPB... , μPC... , μPC... ,
uPD...,
μPD...
The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque 0 sont
Les composants identifiés par une marque 0 sont
critiques pour la sécurité.
Ne les remplacer que par une pièce portant le numéro
spécifié.
Ne les remplacer que par une pièce portant le numéro
spécifié.
• Color Indication of Appearance Parts
Example:
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
The components identified by mark contain confiden-
tial information.
Strictly follow the instructions whenever the components
are repaired and/or replaced.
Destroy and discard the prescribed board and IC after
they are replaced.
Strictly follow the instructions whenever the components
are repaired and/or replaced.
Destroy and discard the prescribed board and IC after
they are replaced.
Les composants identifiés par le symbole contiennent
des informations confidentielles.
Suivez scrupuleusement les instructions chaque fois
qu'un composant est remplacé et / ou réparé.
Veuillez détruire et éliminer les circuits imprimés et / ou
les circuits intégrés que vous avez remplacés.
Suivez scrupuleusement les instructions chaque fois
qu'un composant est remplacé et / ou réparé.
Veuillez détruire et éliminer les circuits imprimés et / ou
les circuits intégrés que vous avez remplacés.
标识有
的元件包含机密信息。
更换或维修元件时，请严格遵守指⽰。
更换后的电路板和IC，应予以报废。
更换后的电路板和IC，应予以报废。
(JAPANESE)
【使用上の注意】
• ここに記載されている部品は, 補修用部品であるため, 回路図及びセットに付いてい
る部品と異なる場合があります。
• -XX, -Xは標準化部品のため, セットに付いている部品と異なる場合があります。
• *印の部品は常備在庫しておりません。
• コンデンサの単位でuFはμFを示します。
• 抵抗の単位Ωは省略してあります。
金 被：金属被膜抵抗。
サンキン：酸化金属被膜抵抗。
• インダクタの単位でuHはμHを示します。
• 半 導 体 の 名 称 でuA..., uPA..., uPB..., uPC..., uPD...等 は そ れ ぞ れ μA..., μPA...,
• *印の部品は常備在庫しておりません。
• コンデンサの単位でuFはμFを示します。
• 抵抗の単位Ωは省略してあります。
金 被：金属被膜抵抗。
サンキン：酸化金属被膜抵抗。
• インダクタの単位でuHはμHを示します。
• 半 導 体 の 名 称 でuA..., uPA..., uPB..., uPC..., uPD...等 は そ れ ぞ れ μA..., μPA...,
μPB..., μPC..., μPD...を示します。
図面番号で部品を指定するときは基板名又はブロッ
クを併せて指定してください。
クを併せて指定してください。
お願い
0印の部品，または0印付の点線で囲まれた部品は，
安全性を維持するために，重要な部品です。
従って交換時は，必ず指定の部品を使用してくださ
い。
安全性を維持するために，重要な部品です。
従って交換時は，必ず指定の部品を使用してくださ
い。
• 外装部品色表示
例：
(SILVER) ：セットの色を表す。
(Silver) ：部品の色を表す。
印の部品には，秘密情報が含まれています。
修理の際は，指示に従った対応を行ってください。
交換後の対象基板及び対象ICは，破壊のうえ廃棄し
てください。
交換後の対象基板及び対象ICは，破壊のうえ廃棄し
てください。
View Position
Right View
Left View
Front View
Bottom View
Top View
Back View
VC-1023
Projector Model
Non Projector Model
1
BT Panel
5
F Panel Assy
3
Hinge Cover (R)
2
BT Lid Assy
4
L Top Assy
8
MM-102 Board
• FP-2060 Flexible Board
6
Cabinet Block Assy
9
Lens Block
• CM-1004 Board
• FP-2190 Flexible Board
• FP-2190 Flexible Board
7
Control Switch Block
q;
GY-1005 Board
• FP-2183 Flexible Board
qa
VC-1023 Board
qs
Cabinet (R) Block
• PJ-1009 Board
• PD-1029 Board
• FP-2106 Flexible Board
• FP-2193 Flexible Board
• PD-1029 Board
• FP-2106 Flexible Board
• FP-2193 Flexible Board
qs
Cabinet (R) Block
• PD-1028 Board
• FP-2184 Flexible Board
• FP-2184 Flexible Board
PJ270/PJ270E/PJ275
Click on the first or last page to see other HDR-CX240 / HDR-CX240E / HDR-PJ240 / HDR-PJ240E / HDR-PJ270 / HDR-PJ270E / HDR-PJ275 (serv.man2) service manuals if exist.