Sony HDR-CX240 / HDR-CX240E / HDR-PJ240 / HDR-PJ240E / HDR-PJ270 / HDR-PJ270E / HDR-PJ275 (serv.man2) Service Manual ▷ View online
SERVICE MANUAL
SERVICE NOTE (Check the following note before the service.)
Revision History
Published by Sony Techno Create Corporation
Sony Corporation
LEVEL
2
HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
983477231.pdf
Digital HD Video Camera Recorder
The components identified by mark
0 or dotted line with mark 0 are
critical for safety.
Replace only with part number
specified.
0 or dotted line with mark 0 are
critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque
marque
0 sont critiques pour la
sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
Ne les remplacer que par une
pièce portant le numéro spécifié.
9-834-772-31
Ver.
Date
History
Contents
S.M. Rev.
issued
1.0
2014.01
Official Release
—
—
2014A08-1
© 2014.01
1-1.
POWER SUPPLY DURING REPAIRS
1-2.
PRECAUTION ON REPLACING THE VC-1023 BOARD
1-3.
CHECKING THE Wi-Fi FUNCTION (HDR-PJ275)
1-4.
SELF-DIAGNOSIS FUNCTION
1-5.
NOTE ON REPLACING PROJECTOR UNIT (Projector Model)
Ver. 1.0 2014.01
US Model
Canadian Model
AEP Model
UK Model
North European Model
E Model
Australian Model
Chinese Model
Korea Model
Brazilian Model
HDR-CX240/CX240E/PJ240/PJ240E/
PJ270/PJ270E/PJ275
Photo: HDR-CX240/Black
– 2 –
HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
SPECIFICATIONS
System
Signal format:
NTSC color, EIA standards (HDR-CX240/
PJ240/PJ270/PJ275)
PAL color, CCIR standards (HDR-CX240E/
PJ240E/PJ270E)
HD
HD
TV
Movie recording format:
AVCHD (AVCHD format Ver.2.0
compatible):
Video:
Video:
MPEG-4
AVC/H.264
Audio: Dolby Digital 2ch
Dolby Digital Stereo Creator
*1
MP4:
Video:
Video:
MPEG-4
AVC/H.264
Audio: MPEG-4 AAC-LC 2ch
*1
Manufactured under license from Dolby
Laboratories.
Photo file format:
DCF
DCF
Ver.2.0
Compatible
Exif
Ver.2.3
Compatible
MPF Baseline Compatible
Recording media (Movie/Photo):
Internal
Internal
memory
HDR-PJ270/PJ270E/PJ275: 8 GB
Memory Stick Micro (Mark2) media
microSD card (Class 4 or faster)
The capacity that a user can use
(Approx.)
HDR-PJ270/PJ270E/PJ275:
7.75
HDR-PJ270/PJ270E/PJ275:
7.75
GB
*2
*2
1 GB equals 1 billion bytes, a portion of
which is used for system management and/
or application files. Only preinstalled dem-
onstration movie may be deleted.
or application files. Only preinstalled dem-
onstration movie may be deleted.
Image device:
3.1 mm (1/5.8 type) CMOS Sensor
Recording pixels (photo, 16:9):
Max. 9.2 mega pixels (4 032 × 2 272)
*3
Gross: Approx. 2 510 000 pixels
Effective (movie, 16:9)
*4
:
Approx. 2 100 000 pixels
Effective (photo, 16:9):
Approx. 2 290 000 pixels
Effective (photo, 4:3):
Approx. 1 710 000 pixels
Lens:
ZEISS
ZEISS
Vario-Tessar
Lens
27× (Optical), 54× (Clear Image
Zoom, while recording movies)
*4
,
320×
(Digital)
F1.9 - F4.0
Focal
length:
f=2.1 mm - 57.0 mm (3/32 in. - 2 1/4 in.)
When converted to a 35 mm still camera
For
movies
*4
: 29.8 mm - 1 609.2 mm
(1 3/16 in. - 63 3/8 in.) (16:9)
For photos: 29.8 mm - 804.0 mm
(1 3/16 in. - 31 3/4 in.) (16:9)
Color temperature: [Auto], [One Push], [Indoor],
[Outdoor]
Minimum illumination:
6 lx (lux) (in default setting,
shutter speed 1/30 second (HDR-CX240/
PJ240/PJ270/PJ275)
or
1/25 second (HDR-CX240E/
PJ240E/PJ270E))
3 lx (lux) ([Low Lux] is set to [On],
shutter speed 1/30 second (HDR-CX240/
PJ240/PJ270/PJ275)
or
1/25 second (HDR-CX240E/
PJ240E/PJ270E))
*3
The unique image processing system of
Sony’s BIONZ-X allows still image resolu-
tion equivalent to the sizes described.
tion equivalent to the sizes described.
*4
[
SteadyShot] is set to [Standard] or
[Off].
Input/Output connectors
HDMI OUT jack: HDMI micro connector
PROJECTOR IN jack (HDR-PJ240/
PJ240E/PJ270/PJ270E/PJ275):
PROJECTOR IN jack (HDR-PJ240/
PJ240E/PJ270/PJ270E/PJ275):
HDMI micro connector
USB jack: Type A (Built-in USB)
USB connector is only for output
(HDR-CX240E/PJ240E/PJ270E).
Multi Terminal
USB connector is only for output
(HDR-CX240E/PJ240E/PJ270E).
Multi Terminal
LCD monitor
Picture: 6.7 cm (2.7 type, aspect ratio 16:9)
Total number of pixels:
Total number of pixels:
230 400 (960 × 240)
Projector (HDR-PJ240/PJ240E/
PJ270/PJ270E/PJ275)
PJ270/PJ270E/PJ275)
Projection type: DLP
Light source: LED (R/G/B)
Focus: Manual
Throw Distance: 0.5 m (1.6 feet) or over
Contrast ratio: 1 500:1
Resolution (output): 640 × 360
Continuous projection time (when
Light source: LED (R/G/B)
Focus: Manual
Throw Distance: 0.5 m (1.6 feet) or over
Contrast ratio: 1 500:1
Resolution (output): 640 × 360
Continuous projection time (when
using the supplied battery pack):
Approx. 1 h. 10 min.
Wireless LAN (HDR-PJ275)
Supported standard:
IEEE 802.11 b/g/n
Frequency: 2.4 GHz
Supported security protocols: WEP/
WPA-PSK/WPA2-PSK
Configuration method: WPS (Wi-Fi
Protected
Supported security protocols: WEP/
WPA-PSK/WPA2-PSK
Configuration method: WPS (Wi-Fi
Protected
Setup)/manual
Access method: Infrastructure Mode
NFC: NFC Forum Type 3 Tag compliant
NFC: NFC Forum Type 3 Tag compliant
General
Power requirements: DC 3.6 V
(battery pack), DC 5 V 1 500 mA
(AC
Adaptor)
USB Charging: DC 5 V 800 mA
Average power consumption:
Average power consumption:
During camera recording using LCD
monitor at normal brightness:
HDR-CX240/CX240E:
1.8
W
HDR-PJ240/PJ240E/PJ270/
PJ270E/PJ275:
PJ270E/PJ275:
1.9
W
Operating temperature: 0 °C to 40 °C
(32 °F to 104 °F)
Storage temperature: –20 °C to
+60 °C (–4 °F to +140 °F)
Dimensions (approx.):
HDR-CX240/CX240E:
HDR-CX240/CX240E:
54.0 mm × 59.5 mm × 128.0 mm
(2 1/4 in. × 2 3/8 in. × 5 1/8 in.) (w/h/d)
including the projecting parts
54.0 mm × 59.5 mm × 128.0 mm
(2 1/4 in. × 2 3/8 in. × 5 1/8 in.) (w/h/d)
including the projecting parts, and the
supplied rechargeable battery pack inserted
HDR-PJ240/PJ240E/PJ270/
PJ270E/PJ275:
PJ270E/PJ275:
59.0 mm × 59.5 mm × 128.0 mm
(2 3/8 in. × 2 3/8 in. × 5 1/8 in.)
(w/h/d) including the projecting parts
59.0 mm × 59.5 mm × 128.0 mm
(2 3/8 in. × 2 3/8 in. × 5 1/8 in.)
(w/h/d) including the projecting parts,
and the supplied rechargeable battery pack
inserted
Mass (approx.)
HDR-CX240/CX240E:
Mass (approx.)
HDR-CX240/CX240E:
190 g (6.7 oz) main unit only 215 g (7.6 oz)
including the supplied rechargeable battery
pack
including the supplied rechargeable battery
pack
HDR-PJ240/PJ240E/PJ270/PJ270E/PJ275:
210 g (7.4 oz) main unit only
235 g (8.3 oz) including the
supplied rechargeable battery pack
AC Adaptor AC-UUD11
Power requirements: AC 100 V -
240 V, 50 Hz/60 Hz
Current consumption: 200 mA
Power consumption: 11 W
Output voltage: DC 5.0 V, 1 500 mA
Operating temperature: 0 °C to 50 °C
Power consumption: 11 W
Output voltage: DC 5.0 V, 1 500 mA
Operating temperature: 0 °C to 50 °C
(32 °F to 122 °F)
Storage temperature: –20 °C to
+60 °C (–4 °F to +140 °F)
Rechargeable battery pack NP-BX1
Used battery: Lithium-ion battery
Maximum voltage: DC 4.2 V
Nominal voltage: DC 3.6 V
Maximum charge voltage: DC 4.2 V
Maximum charge current: 1.89 A
Capacity: 4.5 Wh (1 240 mAh)
Maximum voltage: DC 4.2 V
Nominal voltage: DC 3.6 V
Maximum charge voltage: DC 4.2 V
Maximum charge current: 1.89 A
Capacity: 4.5 Wh (1 240 mAh)
Design and specifications of your camcorder and
accessories are subject to change without notice.
accessories are subject to change without notice.
Model information table
Model
CX240
CX240E
PJ240
PJ240E
PJ270
PJ270E
PJ275
Destination
US, CND, E,
KR, BR
AEP, UK, NE,
E, AUS, CH
E, KR, BR
AEP, UK, NE,
E, AUS, CH
CND, E
E
US
COLOR system
NTSC
PAL
NTSC
PAL
NTSC
PAL
NTSC
Internal recording
media
–
–
–
–
Internal memory
8 GB
Internal memory
8 GB
Internal memory
8 GB
LENS
LSV-1610B
LSV-1610B
LSV-1610B
LSV-1610B
LSV-1610B
LSV-1610B
LSV-1610B
Projector
–
–
3
3
3
3
3
GPS
–
–
–
–
–
–
–
EVF
–
–
–
–
–
–
–
Wi-Fi
–
–
–
–
–
–
3
NFC
–
–
–
–
–
–
3
Multi interface
shoe
–
–
–
–
–
–
–
Charging capacitor
(for flash)
–
–
–
–
–
–
–
MODEL GROUP
Projector Model:
PJ240/PJ240E/PJ270/PJ270E/PJ275
Non Projector Model: CX240/CX240E
• Abbreviation
AUS: Australian
model
BR: Brazilian
model
CH: Chinese
model
CND:
Canadian
model
KR: Korea
model
NE: North European mode
– 3 –
HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY
SONY.
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY
SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES
SUPPLÉMENTS PUBLIÉS PAR SONY.
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES
SUPPLÉMENTS PUBLIÉS PAR SONY.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes and
bridges.
bridges.
2. Check the interboard wiring to ensure that no wires are pinched or
contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs of
deterioration. Point them out to the customer and recommend their
replacement.
replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
6. Flexible Circuit Board Repairing
• Set the soldering iron tip temperature to 350 °C approximately.
• Do not touch the soldering iron on the same conductor of the circuit
• Do not touch the soldering iron on the same conductor of the circuit
board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering.
UNLEADED SOLDER
This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead free
mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with the
Boards requiring use of unleaded solder are printed with the lead free
mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with the
lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
• Set the soldering iron tip temperature to 350 °C approximately.
If cannot control temperature, solder/unsolder at high temperature
for a short time.
Caution: The printed pattern (copper foil) may peel away if the
for a short time.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
Unleaded solder is more viscous (sticky, less prone to
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
• Be sure to control soldering iron tips used for unleaded solder and
those for leaded solder so they are managed separately. Mixing un-
leaded solder and leaded solder will cause detachment phenomenon.
leaded solder and leaded solder will cause detachment phenomenon.
注意
如果电池更换不当会有爆炸危险。
只能用同样类型或等效类型的电池来更换。
务必按照说明处置用完的电池。
只能用同样类型或等效类型的电池来更换。
务必按照说明处置用完的电池。
1-1
HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
1. SERVICE NOTE
1-1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (4.2 Vdc), the power is shut off
so that the unit cannot operate.
These following method is available to prevent this.
so that the unit cannot operate.
These following method is available to prevent this.
Method:
Use the AC power adaptor.
1-2. PRECAUTION ON REPLACING THE VC-1023 BOARD
Note the following when replacing the board.
Destination Data
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATION DATA WRITE”.
After the board replacement, the error of the built-in recording media may be displayed. In this case, execute the [DESTINATION DATA WRITE]
then the error will be cleared. If it is not cleared with [DESTINATION DATA WRITE], format the built-in recording media.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATION DATA WRITE”.
After the board replacement, the error of the built-in recording media may be displayed. In this case, execute the [DESTINATION DATA WRITE]
then the error will be cleared. If it is not cleared with [DESTINATION DATA WRITE], format the built-in recording media.
USB Serial Save
When you replace to the repairing board, get the data from the former one.
Start the Adjust Manual in the Adjust Station and perform “USB SERIAL SAVE” to get the data.
Start the Adjust Manual in the Adjust Station and perform “USB SERIAL SAVE” to get the data.
USB Serial No. and Product ID
The unit is shipped after an ID (USB Serial No.) unique to each unit and an ID (Product ID) unique to each model have been written.
These IDs have not been written in a new board for service, and therefore they must be entered after the board replacement.
After the board has been replaced with a board for service, start the Adjust Manual in the Adjust Station and execute the “PRODUCT ID & USB
SERIAL No. INPUT” and enter these IDs.
These IDs have not been written in a new board for service, and therefore they must be entered after the board replacement.
After the board has been replaced with a board for service, start the Adjust Manual in the Adjust Station and execute the “PRODUCT ID & USB
SERIAL No. INPUT” and enter these IDs.
Note: A newly entered Product ID is not always equal to the ID before board replacement. If the new ID differs from the previous ID, it may cause a difference
from the ID registered by the customer.
Data for projector (Projector Model)
Before replacing the board with a spare board, acquire the following data from the current board.
• Fixed value (that shows irradiation performance of the projector).
• Serial number of the projector unit.
To acquire the data, start Adjust Manual from Adjust Station and select [Projector Data Reference] on the [DATA] tab.
• Fixed value (that shows irradiation performance of the projector).
• Serial number of the projector unit.
To acquire the data, start Adjust Manual from Adjust Station and select [Projector Data Reference] on the [DATA] tab.
Update of MAC Address (HDR-PJ275)
When replacing a VC board, the IC’s unique number (MAC address) must be reloaded.
After the board has been replaced with a board for service, perform the following procedure to reload the IC’s unique number (MAC address).
After the board has been replaced with a board for service, perform the following procedure to reload the IC’s unique number (MAC address).
Note: Perform this operations after all work has been done.
1. Download the latest-version Adjust Manual.
2. Install the downloaded Adjust Manual.
3. Start the Adjust Manual, and execute “Wireless LAN Setting (MAC address)” on the ADJUST tab.
2. Install the downloaded Adjust Manual.
3. Start the Adjust Manual, and execute “Wireless LAN Setting (MAC address)” on the ADJUST tab.
If “Wireless LAN check” is not executed and the backup data before replacement is restored, the MAC address in the Wi-Fi module does not match
the MAC address in the flash memory, causing an error during Wi-Fi transfer.
the MAC address in the flash memory, causing an error during Wi-Fi transfer.
Note: The “LOAD AND WRITE” function in “ADJUSTMENT DATA BACKUP” on the DATA tab in the Adjust manual overwrites all data of the unit. Therefore,
the MAC address updated during the above procedure is also overwritten.
After the replacement and repair, the MAC address is changed, and thus the re-setting for connection devices is required. Accordingly, download the
Flyer of WLAN Reset (Flyer of WLAN Reset_9834752[][].pdf) and print out it, and attach it to the set when returning the set to customer.
Flyer of WLAN Reset (Flyer of WLAN Reset_9834752[][].pdf) and print out it, and attach it to the set when returning the set to customer.
About unit with Internal Memory Model (PJ270/PJ270E/PJ275)
After the board replacement, execute the procedure below first.
1. Execute the [DESTINATION DATA WRITE] of ADJUST tab in the Adjust Manual.
2. Execute the script files below. (Refer to the flowchart in Fig. 1)
1. Execute the [DESTINATION DATA WRITE] of ADJUST tab in the Adjust Manual.
2. Execute the script files below. (Refer to the flowchart in Fig. 1)
• 14DdmMmcReadTestMINI_v6.vbe
• 14DdmMmcMakePartition_v6.vbe
• 14DdmMmcMakePartition_v6.vbe
Unless these script files are executed, the following symptoms may appear.
Make sure execute the above script files.
• The internal memory is not recognized as a media.
• The management file saved in the internal memory model cannot be repaired.
• The internal memory cannot be formatted.
Make sure execute the above script files.
• The internal memory is not recognized as a media.
• The management file saved in the internal memory model cannot be repaired.
• The internal memory cannot be formatted.
START
END
Reactive the camcorder automatically
Disconnect the USB cable,
and turn off the power switch.
Select the "USB CONNECT" to establish
the connection
Execute
the "14DdmMmcReadTestMINI_v6.vbe"
(several second later)
Wait until "SetOverallReadMINI OK" display
(10 seconds later)
Reactive the camcorder automatically
Execute
the "14DdmMMCMakePartition_v6.vbe"
(several second later)
Wait until "MakePartition OK" display
During the power is turning-on,
pull-out the AC-adapter.
Then connect the AC-adapter Again
(It's running with blue color monitor.)
Connect to the PC with a USB cable,
and turn on the power switch.
* by SEUS driver
Fig.1