DOWNLOAD Sony DCR-TRV60 / DCR-TRV60E / DCR-TRV70 (serv.man2) Service Manual ↓ Size: 8.5 MB | Pages: 99 in PDF or view online for FREE

2-18

CN1006

Extension cable 
(100P, 0.5mm)
(J-6082-352-A)

CN1004

CN1003

VC-314 board

DI-088 board

CN1009

CN1500

CN4003

CN4201

VC-314

DI-088

*1

*2

1

1

16

8

9

16

Cabinet (L) block assembly

Mechanism deck

DC-IN connector

CPC-7 jig
(J-6082-382-A)

Cabinet (LS) block assembly,
Lens block assembly

Monitor TV

Adjustment remote
commander (RM-95)

Audio/video jack

LANC jack

AC power
adaptor

AC IN

Control switch block
(FK-4110)(27P)

To check the VTR section, set the VTR to the “Forced VTR power ON” mode.
Operate the VTR functions using the adjustment remote commander (with the HOLD switch set in the OFF position).

Setting the “Forced VTR Power ON” mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: D, address: 10, set data: 02, and
    press the PAUSE button of the adjustment
     remote commander.

*

1: Caution: High voltage

*2: To eject a cassette, connect the cabinet (L) block assembly.

Exiting the “Forced VTR Power ON” mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: D, address: 10, set data: 00, and
     press the PAUSE button of the adjustment
      remote commander.
4) Select page: 0, address: 01, and set data: 00.

(page 2-4)

(page 2-5)

(page 2-6)

(page 2-8)

(page 2-10)

(page 2-12)

(page 2-13)

(page 2-17)

2-3. CABINET (R) BLOCK ASSEMBLY (1)...........................................................

2-4. CABINET (R) BLOCK ASSEMBLY (2)...........................................................

2-7. EVF BLOCK ASSEMBLY...............................................................................

2-9. STROBOSCOPE BLOCK ASSEMBLY.........................................................

2-11. DI-088 BOARD...........................................................................................

2-12.  CABINET (LS) BLOCK ASSEMBLY AND LENS BLOCK ASSEMBLY......

2-16. VC-314 BOARD, MICROPHONE UNIT AND MECHANISM DECK...........

2-5. BATTERY PANEL ASSEMBLY.......................................................................

1

2

3

4

5

7

8

6

PROCEDURE OF REMOVING MECHANISM DECK (VTR CHECK)

2-19

7

 Grip cabinet assembly,

     CS frame assembly

hole

3

 Two 

tapping

     screws
     (M1.7 

× 

5)

5

 T

apping screw

     (M1.7 

× 

5)

1

 T

apping screw

     (M1.7 

× 

5)

9

 Two 

tapping

     screws
     (M1.7 

× 

5)

4

 Three 

screws

     (M1.7 

× 

2.5), 

      lock ace, p2

6

 S

crew

     (M1.7 

× 

2.5), 

      lock ace, p2

2

 Two s

crews

     (M1.7 

× 

2.5), 

      lock ace, p2

8

 Cabinet (L) block assembly

qd

 JK-245 board

q;

 Two 

screws

     (M1.7 

× 

2.5), 

      lock ace, p2

qf

 FP-657 flexible

     board (10P)

qs

 FP-658 flexible

     board (14P)

qg

 External connector

qh

 Cabinet (L) assembly

qa

 L frame

When re-assembling, pass the
flexible board through the hole
of the CS frame assembly.

Remove this screw after the CS
frame assembly is opened.

2-20

1

 S

crew

     (M1.7 

× 

2.5), 

      o-no.+p2

Small

Wide

9

 Two 

screws

     (M1.7 

× 

2.5), 

      lock ace, p2

6

 Memory stick connector

     assembly (10P) 

qa

 Memory stick

     connector (10P) 

q;

 MS connector retainer

White pin

8

 Control switch block

     (FK-4110) 

7

 Two 

tapping screws

     (M1.7 

× 

5)

3

 T

apping screw

     (M1.7 

× 

5)

4

 T

apping screw

     (M1.7 

× 

5)

When installing the REC block of the control
(FK-4110) switch block, align the power
switch and the white pin with the position
shown in the illustration. And then install it.

5

 Control switch block (FK-4110) 

     (10P)

Control (FK-4110) switch block
(backside of the REC block)

When re-assembling, pass the
flexible board through the hole
of the CS frame assembly.

If the zoom lever comes off,
install it as shown.

hole

Zoom lever 

POWER

Power switch

2

 Open the CS frame assembly

     in the direction of the arrow .

2-21

9

 

Tapping screw

     (M1.7 

× 

5)

8

 FP-660 flexible

     board (39P)

4

 Harness speaker 

     (1.6CM) (2P)

5

 Harness 

     (PC-130 )(4P)

6

 Harness 

     (PC-129) (20P)

2

 Tape (A)

1

 Tape (A)

3

 Tape (A)

Tape (A)

Hole

Attach the tape (A) as shown.

Insert the protrusion of the CK-130
board into the hole and then tighten
by screw.

Protrusion

q;

 CK-130 board 

CK-130 board 

7

 

Flexible board 

    (from the FP-667)
    (6P)