Sony DCR-TRV60 / DCR-TRV60E / DCR-TRV70 (serv.man2) Service Manual ▷ View online
2-6
DCR-TRV60/TRV60E/TRV70
2-5. BATTERY PANEL ASSEMBLY
5
Harness
(battery terminal board) (3P)
2
Three
screws
(M1.7
×
4),
lock ace, p2
Caution
1
Harness retainer sheet (DI)
Harness retainer
sheet (DI)
sheet (DI)
Attach the harness retainer
sheet (D1) as shown.
sheet (D1) as shown.
4
Open the grip cabinet block
in the direction of the arrow.
3
Raise the EVF block in the
direction of the arrow
A
.
6
Battery panel
assembly
A
2-7
DCR-TRV60/TRV60E/TRV70
2-6. BATTERY PANEL ASSEMBLY, BATTERY BOARD
9
Strap sheet metal (lower)
7
Battery panel assembly
2
Harness guide
1
Two hooks
8
Battery board
6
Battery board assembly
4
CPC lid
3
Screw
(M1.7
×
4),
lock ace, p2
5
Two
screws
(M1.7
×
2.5),
lock ace, p2
2-8
DCR-TRV60/TRV60E/TRV70
2-7. EVF BLOCK ASSEMBLY
A
B
1
Screw
(M1.7
×
2.5),
lock ace, p2
6
Two
screws
(M1.7
×
2.5),
lock ace, p2
7
screw
(M1.7
×
2.5),
lock ace, p2
3
Screw
(M1.7
×
2.5),
lock ace, p2
Caution
Caution
8
FP-659 flexible board (16P)
q;
EVF escutcheon
EVF escutcheon
Hole
5
Tape (A)
Tape (A)
Protrusion
The EVF escutcheon comes off
when the EVF block assembly is
removed because it is not
retained by anything any more.
Be careful not to lose the EVF
escutcheon. Install it as shown
for re-assembly.
when the EVF block assembly is
removed because it is not
retained by anything any more.
Be careful not to lose the EVF
escutcheon. Install it as shown
for re-assembly.
2
Slide the EVF block in the
direction of the arrow
A
as
far as it can go.
Attach the tape (A) as shown.
9
Remove the EVF block assembly in the
direction of the arrow.
4
Raise the capacitor of the stroboscope
block in the direction of the arrow
B
.
2-9
DCR-TRV60/TRV60E/TRV70
2-8. LB-086 BOARD
qh
LB-086 board
9
LB-086 board assembly
qg
Lamp guide (20)
q;
Illuminator
qa
Prism sheet
qs
LCD
qd
VF lens assembly
6
VF electrostatic sheet (A)
VF electrostatic
sheet (A)
sheet (A)
4
VF cabinet (upper) assembly
Caution
Caution
Caution
5
FP-659 flexible
board (16P)
FP-659 flexible
board (16P)
board (16P)
Two claws
qf
Two claws
8
Three claws
1
Two tapping
screws
(M1.7
(M1.7
×
5)
VF lens assembly
2
Remove the EVF block in the
direction of the arrow
A
by
releasing the two claws.
Be careful that the pin of the VF lens assembly
comes to the position as shown in the
illustration when re-assembling it.
comes to the position as shown in the
illustration when re-assembling it.
Drawing when viewed
from the side
from the side
Drawing when viewed
from the side
from the side
Drawing when viewed
from the bottom
from the bottom
The concave surface
of the VF lens assembly
of the VF lens assembly
Attach the VF electrostatic sheet (A) as shown.
3
Remove the VF lens
assembly from the VF
cabinet (upper)
assembly in the
direction of the arrow.
cabinet (upper)
assembly in the
direction of the arrow.
A
Tape
Cushion (C)
Hole
Hole
Shaft
Contact point
Give a folding mark along with
the dotted line as shown.
the dotted line as shown.
Align the FP-659 flexible board
(16 P) with the attached tape as
the reference line.
(16 P) with the attached tape as
the reference line.
Contact point
Attach the cushion "c" to the position
shown by the dotted line.
shown by the dotted line.
While the contact point faces
upwovd, pass through it in the
direction the arrow.
upwovd, pass through it in the
direction the arrow.
7
Flexible board
(from the LCD)
(16P)
(16P)
Click on the first or last page to see other DCR-TRV60 / DCR-TRV60E / DCR-TRV70 (serv.man2) service manuals if exist.