Sony DCR-TRV60 / DCR-TRV60E / DCR-TRV70 (serv.man2) Service Manual ▷ View online
2-14
DCR-TRV60/TRV60E/TRV70
qd
FC-092 board
q;
FP-664 board
qa
MF ring assembly
6
Cabinet (LS) block assembly
5
Lens assembly
qf
Lens assembly
9
Tapping Screw
(M1.7
×
3.5)
3
Two tapping
screws
(M1.7
(M1.7
×
5)
8
Screw
(M1.7
×
2.5),
o-no.+p2
2
Screw
(M1.7
×
2.5),
lock ace, p2
qs
Screw
(M1.7
×
2.5),
lock ace, p2
4
Flexible board
(from the lens device)
(31P)
(31P)
7
Flexible board
(from the FP-664 board)
(6P)
(6P)
1
FP-663 flexible board
(8P)
2-13.FP-664 BOARD, FC-092 BOARD
2-15
DCR-TRV60/TRV60E/TRV70
CD-433
qk
CCD block assembly
ql
CD-433 board
qg
TG heat sink (B)
qd
TG heat sink (A)
qh
Sheet (A)
Sheet (A)
Caution
qa
Screw
(M1.7
×
2.5),
lock ace, p2
Radiation sheet (A) Attach the radiation
sheet (A) in the position as shown.
sheet (A) in the position as shown.
qj
Ten soldering points
qf
Two soldering points
4
Seal rubber (N)
7
Lens frame
3
Optical filter block
q;
Lens block assembly
5
CD-433 board assembly
1
Two tapping
screws
(M1.7
(M1.7
×
5)
6
Two tapping
screws
(M1.7
(M1.7
×
3.5)
8
Tapping screw
(M1.7
×
3.5)
2
CD heat sink
9
TG base
qs
Two dowels
2-14.LENS BLOCK ASSEMBLY, CD-433 BOARD
2-16
DCR-TRV60/TRV60E/TRV70
2-15.NS-017 BOARD, SJ-019 BOARD AND JJ-001 BOARD, LASER UNIT
ql
Jack frame
qg
Claw
qf
Claw
5
NS-017 board
assembly
NS holder
NS holder
NS-017
board
board
Guide (NS)
Guide (NS)
NS-017 board
SJ-019 board
4
JJ-001 board assembly
9
SJ-019 board ,FP-665 board
8
Protection sheet (SJ)
Protection sheet (SJ)
qs
Screw
(M1.7
×
2.5),
o-no.+p2
qa
Screw
(M1.7
×
2.5),
lock ace, p2
qd
Screw
(M1.7
×
2.5),
lock ace, p2
q;
Two
screws
(M1.7
×
2.5),
lock ace, p2
Caution
Caution
Caution
Caution
Caution
2
Two tapping
screws
(M1.7
(M1.7
×
5)
6
Tapping screw
(M1.7
×
5)
FP-665 flexible
board (6P)
board (6P)
qk
JJ-001 board
Claw
Laser unit
Laser unit
Hold the NS-017 board with
the NS holder as shown
during re-assembling.
the NS holder as shown
during re-assembling.
Remove the claw of the NS
holder and pull out the
NS-017 board in the
direction of the arrow.
holder and pull out the
NS-017 board in the
direction of the arrow.
Attach the guide (NS) as shown
in the illustration.
in the illustration.
Note that the FP-665 flexible
board is positioned under the
protrusion when it is re-assembled.
board is positioned under the
protrusion when it is re-assembled.
FP-665 flexible board
Protrusion
Attach the protection sheet (SJ) as shown.
View from
the side
the side
View from
the rear
the rear
Remove the three soldered
points from the FP-665 flexible
board and remove the laser unit.
points from the FP-665 flexible
board and remove the laser unit.
Soldered point
7
FP-663 flexible
board (8P)
1
FP-661 flexible
board (8P)
qj
FP-661 flexible
board (8P)
3
FP-662 flexible
board (14P)
qh
FP-662 flexible
board (14P)
2-17
DCR-TRV60/TRV60E/TRV70
2-16.VC-314 BOARD, MICROPHONE UNIT AND MECHANISM DECK
VC-314
7
Microphone unit
qh
VC sheet (retainer)
VC sheet
(retainer)
(retainer)
qk
VC sheet
VC sheet
A side
B side
qg
High voltage sheets
High voltage
sheets
sheets
qj
VC sheet (btob)
VC sheet
(btob)
(btob)
wa
MD frame assembly
ws
Mechanism deck
5
Cabinet (L) block assembly
4
VC-314 board, microphone unit
and mechanism deck
3
Two
screws
(M1.7
×
2.5),
lock ace, p2
8
MD sheet
9
MD flexible sheet
MD sheet
MD flexible sheet
2
FP-658 flexible
board (14P)
1
Control switch block
(FK-4110)(27P)
6
Microphone unit
Harness (4P)
ql
Screw
(M1.4
×
1.5)
w;
Three
screws
(M1.4
×
1.5)
Caution
Caution
Caution
0~2mm
A
A
B
B
Attach each sheet
as shown.
as shown.
Attach the flexible
board as shown.
board as shown.
Attach each sheet as shown.
qf
Remove the VC-314 board
in the direction of the arrow.
qa
FP-468 flexible
board (27P)
q;
Flexible board
(from the capstan motor)
(27P)
(27P)
qs
Flexible board
(from the drum motor)
(10P)
(10P)
qd
Flexible board
(from the video head)
(10P)
(10P)
Click on the first or last page to see other DCR-TRV60 / DCR-TRV60E / DCR-TRV70 (serv.man2) service manuals if exist.