Sony DCR-TRV40 / DCR-TRV40E / DCR-TRV50 / DCR-TRV50E Service Manual ▷ View online
2-11
DCR-TRV40/TRV40E/TRV50/TRV50E
2-12.EVF SECTION
2-13.FLASH UNIT (FLASH SECTION) (1)
VC-283
DD-176
1
Two tapping screws
(M1.7
×
5)
4
EVF section
2
FP-458 flexible board
(21P)
3
Remove the EVF section
from the groove.
2
Two screws (M1.7
×
4),
lock ace, p2
3
Remove the Grip cover
in the direction of the arrow.
1
Open the cassette lid
4
Turn over the insulating sheet
5
Flash unit
Shorting jig
(1k
(1k
Ω
/ 1w)
Power supply
capacitor
6
Remove the flexible board (45P)
from the CN4607.
The power supply capacitor of the Flash unit is
charged to the voltage as high as 300 V at a
maximum. The high voltage is not discharged
even after the main power of the machine is
simply turned off and the charged potential still
remains.
Discharge the residual voltage by referring to
Service Note (page 1-2).
charged to the voltage as high as 300 V at a
maximum. The high voltage is not discharged
even after the main power of the machine is
simply turned off and the charged potential still
remains.
Discharge the residual voltage by referring to
Service Note (page 1-2).
Caution
Caution
2-12
DCR-TRV40/TRV40E/TRV50/TRV50E
2-14.FLASH UNIT (FLASH SECTION) (2)
VC-283
DD-176
5
Tapping screw
(M1.7
×
5)
1
From the flash unit
(33P)
2
Dowel
4
Remove the ST cover
in the direction of the arrow.
3
Claw
2-15.FLASH UNIT (FLASH SECTION) (3)
VC-283
DD-176
2
From the flash unit (45P)
The Flash unit (45P)
2
is routed through the gap
between the cabinet L section and the mechanism
deck assembly. If the Flash unit is removed forcibly,
the other flexible boards may be damaged because
the Flash unit is removed from the gap. Be careful
not to damage the flexible board.
deck assembly. If the Flash unit is removed forcibly,
the other flexible boards may be damaged because
the Flash unit is removed from the gap. Be careful
not to damage the flexible board.
3
Two dowels
4
Flash unit
1
Open the
cassette lid
Caution
Caution
2-13
DCR-TRV40/TRV40E/TRV50/TRV50E
2-16.FLASH UNIT (FLASH SECTION) (4)
6
Screw
(M1.7
×
2.5),
lock ace, p2
8
Bolt (M1.4
×
3)
2
Two claws
4
Two
dowels
7
Two dowels
9
Two dowels
3
ST cabinet (upper)
5
ST cabinet (lower)
qa
Flash unit
0
ST hinge assembly
Hinge assembly
To install the Flash unit into the
Hinge assembly, set the switch
position as shown in the illustration.
Hinge assembly, set the switch
position as shown in the illustration.
1
Two tapping screws
(M1.7
×
5)
Flash unit
Caution
2-14
DCR-TRV40/TRV40E/TRV50/TRV50E
2-17.DD-176 BOARD
DD
-
176
VC
-283
1
16
MA-408 board (37P)
DD-176 board
LB-078 board
[DD-176 BOARD SERVICE POSITION]
Adjustment remote
commander (RM-95)
commander (RM-95)
FP-458 flexible board
(21P)
(21P)
JK-219 board (37P)
AC power
adaptor
adaptor
AC IN
CPC-7 jig
(J-6082-382-A)
(J-6082-382-A)
Extension cord (100P)
(J-6082-413-A)
(J-6082-413-A)
Battery terminal board
(6P)
(6P)
Front panel section
VF lens assembly
DD-
176
176
VC-283
4
Two screws
(M1.7
×
2.5),
lock ace, p2
2
FP-459 flexible board
(20P)
6
DD-176 board
7
VC heat sink,
VC radiation sheet B,
VC insulating sheet
VC insulating sheet
3
Zoom cover
5
Board to board connector (100P)
1
From the flash unit
(33P)
Click on the first or last page to see other DCR-TRV40 / DCR-TRV40E / DCR-TRV50 / DCR-TRV50E service manuals if exist.