DOWNLOAD Sony DCR-TRV40 / DCR-TRV40E / DCR-TRV50 / DCR-TRV50E Service Manual ↓ Size: 14.89 MB | Pages: 127 in PDF or view online for FREE

2-3

NOTE: Follow the disassembly procedure in the numerical order given.

PD-

165

PD-

165

4

 P cabinet (c) assembly

7

 

P cabinet (M), 

     Cushion (C), 
     Ground plate (P)

q;

 

Liquid crystal 

     indicator module

8

 

Touch panel

9

 

Cushion (L)

qa

 

Back light

     (Cold cathode fluorescent tube)

Back light
(Cold cathode fluorescent tube)

Touch panel

1

 

Two screws

     (M1.7 

× 

4), 

     lock ace, p2

B

A

D

C

B

A

5

 

Two

     dowels

6

 

Claw

C

D

qs

 

PD-165 board, 

     Inverter transformer unit,
     Indication LCD block assembly, 
     P frame assembly

1

16

Inverter transformer unit

2

 

Two screws

     (M1.7 

× 

4), 

     lock ace, p2

Liquid crystal indicator module

3

 

Five claws

Adjustment remote
commander (RM-95)

AC power
adaptor 

AC IN

CPC-7 jig
(J-6082-382-A)

PD-165 board

2-4

B

A

2

 

Two tapping screws

     (M1.7 

× 

6)

4

 VF cabinet (upper) 

     assembly

6

 VF lens assembly

7

 

LB-078 board, 

Lamp guide

q;

 

LB-078 board

9

 Lamp guide

5

 

Three claws

Prism sheet

Illuminator

3

Two claws

8

 Two claws

1

 Raise the EVF in the 

     direction of the arrow 

A

 

     and slide it in the direction 
     of the arrow 

B

.

When separating the 

7

 LB-078 board and 

Lamp guide from the 

6

 VF lens assembly 

by removing the three 

5

 claws, do not face 

the side of the VF lens assembly on which 
the LB-078 board is installed, downwards. 
Because the Illuminator and others may fall 
out of the VF lens assembly, hold the 
illuminator and others using tape or paper 
as shown to prevent them from falling. 
Be careful on this point especially when 
removing the LB-078 board and Lamp guide 
because the three claws located in the VF 
lens assembly are easy to break.

Hold the illuminator 
and others using 
tape or paper as 
shown to prevent 
them from falling.

2-5

1

16

VF lens assembly

LB-078 board

Adjustment remote
commander (RM-95)

AC power
adaptor 

AC IN

CPC-7 jig
(J-6082-382-A)

2

 

Screw (M1.7 

× 

4), 

     lock ace, p2

1

 

Screw (M1.7 

× 

4), 

     lock ace, p2

3

 

Claw

4

 Top cabinet

2-6

B

A

7

 

JK-219 board (37P)

1

4

 S

crew

     (M1.7 

× 

4), 

     lock ace, p2

6

 Remove the Front panel section 

     in the direction of the arrow 

B

.

3

 

Open the 

     jack cover assembly

2

 

Two screws

     (M1.7 

× 

4), 

     lock ace, p2

8

 

Front panel section

Open the Flash unit by pushing the 
portion 

A

.

Because the 

7

 Front panel section is connected 

to the main unit by the 

6

 JK-219 board, the 

flexible board may be damaged if you remove 
the Front panel section forcibly. 
Be very careful not to damage the flexible board.

5

 S

crew

     (M1.7 

× 

4), 

     lock ace, p2