Sony DCR-TRV38 / DCR-TRV38E / DCR-TRV39 (serv.man3) Service Manual ▷ View online
81
Editing
Dubbing only desired scenes – Digital program editing (on tape)
When the VCR does not operate correctly
•After checking the code in “About the IR SETUP code” (p. 80), set the IR SETUP or the
•After checking the code in “About the IR SETUP code” (p. 80), set the IR SETUP or the
PAUSEMODE again.
•Place your camcorder at least 30 cm (12 in.) away from the VCR.
•Refer to the operating instructions of your VCR.
•Refer to the operating instructions of your VCR.
Step 3: Adjusting the synchronization of the VCR
You can adjust the synchronization of your camcorder and the VCR.
Prepare a pen and paper for notes.
Before operation, eject the cassette from your camcorder (if inserted).
Prepare a pen and paper for notes.
Before operation, eject the cassette from your camcorder (if inserted).
(1) Insert the recordable cassette into the VCR, then set the VCR to recording
pause.
When you select i.LINK in CONTROL, the recording pause is not necessary.
When you select i.LINK in CONTROL, the recording pause is not necessary.
(2) Select ADJ TEST, then press EXEC.
(3) Select EXECUTE, then press EXEC.
(3) Select EXECUTE, then press EXEC.
IN and OUT are recorded on an image for five times each to calculate the
number values for adjusting the synchronization.
The EXECUTING indicator flashes on the screen. When finished, the
indicator changes to COMPLETE.
number values for adjusting the synchronization.
The EXECUTING indicator flashes on the screen. When finished, the
indicator changes to COMPLETE.
(4) Rewind the tape in the VCR, then start slow playback.
Five IN numbers and corresponding OUT numbers are displayed.
Take a note of the opening number value of each IN and the closing number
value of each OUT.
Take a note of the opening number value of each IN and the closing number
value of each OUT.
(5) Calculate the average of five opening number values of five IN, and the
average of all the closing number values of each OUT.
(6) Select ”CUT-IN,” then press EXEC.
(7) Select the average number value of IN, then press EXEC.
(7) Select the average number value of IN, then press EXEC.
The calculated start position for recording is set.
(8) Select ”CUT-OUT,” then press EXEC.
(9) Select the average number value of OUT, then press EXEC.
(9) Select the average number value of OUT, then press EXEC.
The calculated stop position for recording is set.
(10) Press
RET. to execute.
82
Dubbing only desired scenes – Digital program editing (on tape)
To return to FN
Press
END to return to PAGE1, then press EXIT.
Notes
•When you complete step 3, the image to adjust the synchronization is recorded for
•When you complete step 3, the image to adjust the synchronization is recorded for
about 50 seconds.
•If you start recording from the very beginning of the tape, the first few seconds of the
tape may not be recorded properly. Be sure to allow about 10 seconds’ lead before
starting the recording.
starting the recording.
•When the recording unit cannot be operated properly by the i.LINK cable, leave the
connection as it is, and make the A/V connecting cable settings (p. 78). Video and
audio are sent by digital signals.
audio are sent by digital signals.
2
3
6
8
V I DEO ED I T
ED I T SET
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
RET.
EXEC
0
V I DEO ED I T
ED I T SET
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
RET.
EXEC
0
END
END
V I DEO ED I T
ED I T SET
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
RET.
EXEC
COMPLETE
END
V I DEO ED I T
ED I T SET
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
RET.
EXEC
RETURN
EXECUTE
EXECUTE
ENGAGE
REC PAUSE
REC PAUSE
END
83
Editing
Operation 1: Making a Program
The POWER switch should be set to
.
Operate by touching the panel.
(1) Insert the cassette for playback into your camcorder, and insert the tape for
recording into the VCR.
(2) Press FN to display PAGE1.
(3) Press MENU to display the menu.
(4) Select VIDEO EDIT in
(3) Press MENU to display the menu.
(4) Select VIDEO EDIT in
, then press EXEC (p. 177).
(5) Select TAPE, then press EXEC.
(6) Search for the beginning of the first scene you want to insert using the video
(6) Search for the beginning of the first scene you want to insert using the video
control buttons on the screen, then pause playback. You can fine-adjust one
frame at a time with
frame at a time with
/
.
(7) Press MARK IN on the screen.
The IN point of the first program is set, and the upper part of the program
mark changes to light blue.
mark changes to light blue.
(8) Search for the end of the first scene you want to insert using the video control
buttons on the screen, then pause playback. You can fine-adjust one frame at
a time with
a time with
/
.
(9) Press MARK OUT on the screen.
The OUT point of the first program is set, then the lower part of the program
mark changes to light blue.
mark changes to light blue.
(10) Repeat step 6 to 9.
When one program is set, the program mark changes to light blue.
You can set 20 programs in maximum.
You can set 20 programs in maximum.
To finish making programs
Press
END.
The program is stored in memory until the tape is ejected.
Dubbing only desired scenes – Digital program editing (on tape)
4
5
9
10
7
OTHERS
DATA CODE
BEEP
COMMANDER
D I SPLAY
V I DEO ED I T
BEEP
COMMANDER
D I SPLAY
V I DEO ED I T
EXIT
RET.
EXEC
ED I T
SET
SET
UNDO
ED I T
SET
SET
UNDO
ED I T
SET
SET
UNDO
0:08:55:06
TOTAL
SCENE
SCENE
0:00:00:00
0
0
V I DEO ED I T
MARK
OUT
OUT
START
END
0:09:07:06
TOTAL
SCENE
SCENE
0:00:13:00
1
1
V I DEO ED I T
MARK
I N
I N
START
END
0:10:01:23
TOTAL
SCENE
SCENE
0:00:47:12
3
3
V I DEO ED I T
MARK
I N
I N
START
END
RETURN
TAPE
MEMORY
TAPE
MEMORY
0:32:30:14
TOTAL
SCENE
SCENE
0:00:00:00
0
0
V I DEO ED I T
MARK
I N
I N
START
ED I T
SET
SET
UNDO
END
84
Dubbing only desired scenes – Digital program editing (on tape)
Note
You cannot operate recording during Digital program editing.
You cannot operate recording during Digital program editing.
On a blank portion of the tape
You cannot set IN or OUT.
You cannot set IN or OUT.
If there is a blank portion between the IN point and the OUT point on the tape
The total time may not be displayed correctly.
The total time may not be displayed correctly.
Erasing the program you have set
Erase OUT mark first, and then IN mark of the last set program.
(1) Press UNDO.
(2) Press ERASE 1 MARK. The last set program mark flashes, then the DELETE ?
(2) Press ERASE 1 MARK. The last set program mark flashes, then the DELETE ?
indicator appears.
(3) Press EXEC. The last set program is deleted.
To cancel erasing
Press CANCEL in step 3.
Press CANCEL in step 3.
Erasing all programs
(1) Follow the step 2 to 5 on page 83.
(2) Press UNDO.
(3) Press ERASE ALL. All the set program marks flash, then the DELETE ?
(2) Press UNDO.
(3) Press ERASE ALL. All the set program marks flash, then the DELETE ?
indicator appears.
(4) Press EXEC. All the set programs are deleted.
To cancel erasing all programs
Press CANCEL in step 4.
Press CANCEL in step 4.
Click on the first or last page to see other DCR-TRV38 / DCR-TRV38E / DCR-TRV39 (serv.man3) service manuals if exist.