Sony DCR-TRV24E / DCR-TRV25E / DCR-TRV27E (serv.man2) Service Manual ▷ View online
2-8
DCR-TRV24E/TRV25E/TRV27E
2-7. BATTERY PANEL SECTION
VA-117
1
Screw
(M1.7
×
4),
lock ace, p2
3
Two screws
(M1.7
×
4),
lock ace, p2
1
Screw
(M1.7
×
4),
lock ace, p2
2
CPC lid
4
Open the
cassette lid
5
Remove the Battery panel section
in the direction of the arrow.
7
Battery panel section
6
Battery terminal
board (6P)
2
Strap bracket
(lower)
3
BT panel assembly
4
Battery terminal board
VA-117
VA-117
1
Screw
(M1.7
×
2.5)
7
Screw
(M1.7
×
2.5)
4
Peel off the tape.
5
Slide the EVF slightly
in the direction of the
arrow so that the two
screws
arrow so that the two
screws
6
become
visible.
2
Screw
(M1.7
×
2.5)
3
VA heat sink
6
Two tapping screws
(M1.7
×
5)
8
FP-435 flexible
board (20P)
9
EVF section
2-8. EVF SECTION
2-9
DCR-TRV24E/TRV25E/TRV27E
2-9. LB-077 BOARD
8
Prism sheet
Illuminator
When separating the
q;
LB-077 board
and Lamp guide from the
qa
VF lens
assembly by removing the three
9
claws,
do not face the side of the VF lens
assembly on which the LB-077 board is
installed, downwards.
Because the Illuminator and others may
fall out of the VF lens assembly, hold the
illuminator and others using tape or paper
as shown to prevent them from falling.
Be careful on this point especially when
removing the LB-077 board and Lamp
guide because the three claws located in
the VF lens assembly are easy to break.
assembly on which the LB-077 board is
installed, downwards.
Because the Illuminator and others may
fall out of the VF lens assembly, hold the
illuminator and others using tape or paper
as shown to prevent them from falling.
Be careful on this point especially when
removing the LB-077 board and Lamp
guide because the three claws located in
the VF lens assembly are easy to break.
Caution
Hold the illuminator
and others using
tape or paper as
shown to prevent
them from falling.
and others using
tape or paper as
shown to prevent
them from falling.
1
Screw
(M1.7
×
2.5)
2
Claw
3
Flexible retainer
metal sheet
4
VF flexible retainer sheet
5
Two tapping
screws
(M1.7
(M1.7
×
6)
6
Two claws
qs
Two claws
9
Three claws
7
VF cabinet (upper)
assembly
q;
LB-077 board,
Lamp guide
qf
LB-077 board
qd
Lamp guide
qa
VF lens assembly
2-10
DCR-TRV24E/TRV25E/TRV27E
2-10.VA-117 BOARD (1)
VA-117
VC-281
1
FP-436
flexible board (20P)
(28P)
(12P)
2
FP-434
flexible board
5
VA-117 board
3
Three screws
(M1.7
×
2.5)
4
Board to board
connector (100P)
VC-281
VA-117
[VA-117 BOARD SERVICE POSITION ]
To check the EVF circuit (IC4201 and IC4202), connect the LB-077 board to the VF lens assembly,
and then set the camera to the "Forced EVF ON" mode.
and then set the camera to the "Forced EVF ON" mode.
Setting the “Forced EVF ON” mode
1) Select page: 0, address: 10, and set data: 00.
2) Select page: 3, address: C4, and set data: 67.
3) Select page: 3, address: C5, and set data: 01.
2) Select page: 3, address: C4, and set data: 67.
3) Select page: 3, address: C5, and set data: 01.
Exiting the “Forced EVF ON” mode
1) Select page: 0, address: 10, and set data: 00.
2) Select page: 3, address: C4, and set data: 00.
3) Select page: 3, address: C5, and set data: 00.
2) Select page: 3, address: C4, and set data: 00.
3) Select page: 3, address: C5, and set data: 00.
CPC-8 jig
(J-6082-388-A)
(J-6082-388-A)
AC power
adaptor
adaptor
AC IN
Adjustment remote
commander (RM-95)
commander (RM-95)
Battery terminal
board (6P)
board (6P)
Extension cable (100P)
(J-6082-352-A)
(J-6082-352-A)
VA-117 board
LB-077 board
VF lens
assembly
assembly
FP-435
flexible board (20P)
flexible board (20P)
2-11
DCR-TRV24E/TRV25E/TRV27E
2-11.MAIN CHASSIS COMPLETE ASSEMBLY
VA-117
VA-117
1
Control switch block
(PS-CX2670) (20P)
4
Main chassis
complete assembly
2
FP-443
flexible board (6P)
3
Two screws
(M1.7
×
2.5)
Click on the first or last page to see other DCR-TRV24E / DCR-TRV25E / DCR-TRV27E (serv.man2) service manuals if exist.