Sony DCR-TRV24E / DCR-TRV25E / DCR-TRV27E (serv.man2) Service Manual ▷ View online
2-4
DCR-TRV24E/TRV25E/TRV27E
2-2. EVF SECTION (LB-077 BOARD)
B
A
2
Two tapping screws
(M1.7
×
6)
4
VF cabinet (upper)
assembly
6
VF lens assembly
7
LB-077 board,
Lamp guide
5
Three claws
Prism sheet
Illuminator
3
Two claws
q;
LB-077
board
9
Lamp guide
8
Two claws
1
Raise the EVF in the
direction of the arrow
A
and slide it in the direction
of the arrow
of the arrow
B
.
When separating the
7
LB-077 board and
Lamp guide from the
6
VF lens assembly
by removing the three
5
claws, do not face
the side of the VF lens assembly on which
the LB-077 board is installed, downwards.
Because the Illuminator and others may fall
out of the VF lens assembly, hold the
illuminator and others using tape or paper
as shown to prevent them from falling.
Be careful on this point especially when
removing the LB-077 board and Lamp
guide because the three claws located in
the VF lens assembly are easy to break.
the LB-077 board is installed, downwards.
Because the Illuminator and others may fall
out of the VF lens assembly, hold the
illuminator and others using tape or paper
as shown to prevent them from falling.
Be careful on this point especially when
removing the LB-077 board and Lamp
guide because the three claws located in
the VF lens assembly are easy to break.
Hold the illuminator
and others using
tape or paper as
shown to prevent
them from falling.
and others using
tape or paper as
shown to prevent
them from falling.
Caution
2-5
DCR-TRV24E/TRV25E/TRV27E
CPC-8 jig
(J-6082-388-A)
(J-6082-388-A)
[LB-077 BOARD SERVICE POSITION]
AC power
adaptor
adaptor
AC IN
VF lens assembly
LB-077 board
Adjustment remote
commander (RM-95)
commander (RM-95)
1
Screw
(M1.7
×
4),
lock ace, p2
4
Screw
(M1.7
×
4),
lock ace, p2
2
Screw
(M1.7
×
4),
lock ace, p2
3
Open the
jack cover assembly
5
Remove the Front panel section
in the direction of the arrow.
7
Front panel section
Because the
7
Front panel section is connected
to the main unit by the
6
FP-437 flexible board,
the flexible board may be damaged if you remove
the Front panel section forcibly.
Be very careful not to damage the flexible board.
the Front panel section forcibly.
Be very careful not to damage the flexible board.
Caution
Caution
6
FP-437 flexible board (24P)
2-3. FRONT PANEL SECTION
2-6
DCR-TRV24E/TRV25E/TRV27E
2-4. MA-409, FB-219 BOARDS
1
Microphone (4P)
Route
1
the harness of the Microphone
underneath the MA-409 board as shown
in the illustration below.
in the illustration below.
Caution
MA-409 board
3
Tapping screw
(M1.7
×
3.5)
5
Tapping screw
(M1.7
×
3.5)
6
Focus button retainer
7
Focus button,
FP-444 flexible board
Focus button
4
FB-219 board
8
MA-409 board
FB-219 board
MA-409 board
2
Screw
(M1.7
×
2.5)
[MA-409 BOARD SERVICE POSITION]
FP-437 flexible board (24P)
AC power
adaptor
adaptor
AC IN
Adjustment remote
commander (RM-95)
commander (RM-95)
2-7
DCR-TRV24E/TRV25E/TRV27E
2-5. TOP CABINET ASSEMBLY
2
Screw
(M1.7
×
4),
lock ace, p2
1
Move the EVF in the
direction of the arrow.
3
Screw
(M1.7
×
4),
lock ace, p2
4
Claw
5
Top cabinet assembly
1
Screw
(M1.7
×
4),
lock ace, p2
2
Screw
(M1.7
×
4),
lock ace, p2
4
Screw
(M1.7
×
4),
lock ace, p2
3
Open the
cassette lid
5
Remove the Cabinet (R) section
in the direction of the arrow.
6
FP-434 flexible
board (40P)
7
Cabinet (R) section
Because the
7
Cabinet (R) section is connected
to the main unit using the
6
FP-434 flexible board,
the flexible board may be damaged if you remove
the Cabinet (R) section forcibly. Be very careful not
to damage the flexible board.
the Cabinet (R) section forcibly. Be very careful not
to damage the flexible board.
Caution
2-6. CABINET (R) SECTION
Click on the first or last page to see other DCR-TRV24E / DCR-TRV25E / DCR-TRV27E (serv.man2) service manuals if exist.