Sony DCR-TRV12E / DCR-TRV14E / DCR-TRV19 / DCR-TRV19E (serv.man3) Service Manual ▷ View online
109
“Memory Stick” Operations (DCR-TRV22/TRV33 only)
Inserting the “Memory Stick”
Open the lid of the “Memory Stick” slot. Insert the “Memory Stick” in the “Memory
Stick” slot as far as it can go with the b mark as illustrated, then close the lid.
Stick” slot as far as it can go with the b mark as illustrated, then close the lid.
Ejecting the “Memory Stick”
Open the lid of the “Memory Stick” slot. Slide MEMORY EJECT in the direction of the
arrow.
arrow.
Notes
•If you insert the “Memory Stick” forcibly in the opposite direction, the “Memory
•If you insert the “Memory Stick” forcibly in the opposite direction, the “Memory
Stick” slot may be damaged.
•Do not insert anything other than the “Memory Stick” into the “Memory Stick” slot.
This may cause a malfunction.
While the access lamp is lit or flashing
Do not shake or strike your camcorder because your camcorder is reading the data from
the “Memory Stick” or recording the data on the “Memory Stick.” Do not turn the
power off, eject the “Memory Stick” or remove the battery pack. Otherwise, image data
breakdown may occur.
Do not shake or strike your camcorder because your camcorder is reading the data from
the “Memory Stick” or recording the data on the “Memory Stick.” Do not turn the
power off, eject the “Memory Stick” or remove the battery pack. Otherwise, image data
breakdown may occur.
If “
MEMORY STICK ERROR” appears
Reinsert the “Memory Stick” a few times. The “Memory Stick” may be damaged if the
indicator still appears. If this occurs, use another “Memory Stick.”
indicator still appears. If this occurs, use another “Memory Stick.”
Inserting/Ejecting the “Memory Stick”
Access lamp
MEMORY EJECT
110
Selecting still image quality
The default setting is FINE.
The POWER switch should be set to
or
.
Operate by touching the panel.
(1) Press FN to display PAGE1.
(2) Press MENU to display the menu.
(3) Select STILL SET in
(2) Press MENU to display the menu.
(3) Select STILL SET in
, then press EXEC (p. 179).
(4) Select QUALITY, then press EXEC.
(5) Select a desired image quality, then press EXEC.
(5) Select a desired image quality, then press EXEC.
Image quality settings
Setting
Meaning
FINE (FINE)
Use this mode when you want to record high quality
images. Fine images are compressed to about 1/4.
images. Fine images are compressed to about 1/4.
STANDARD (STD) This is the standard image quality. Standard images are
compressed to about 1/10.
To return to FN
Press EXIT.
Selecting image quality and size
3
4
MEM SET 1
STILL SET
BURST
QUALITY
IMAGESIZE
BURST
QUALITY
IMAGESIZE
OFF
EXIT
RET.
EXEC
MEM SET 1
STILL SET
BURST
QUALITY
IMAGESIZE
BURST
QUALITY
IMAGESIZE
EXIT
RET.
EXEC
FINE
STANDARD
STANDARD
REMAIN
12
12
111
“Memory Stick” Operations (DCR-TRV22/TRV33 only)
Selecting image quality and size
Selecting the still image size (DCR-TRV33 only)
You can select image size 1152
×
864 or 640
×
480 (When the POWER switch is set to
CAMERA or VCR, the image size is automatically set to 640
×
480.)
The default setting is 1152
×
864.
The POWER switch should be set to
.
Operate by touching the panel.
(1) Press FN to display PAGE1.
(2) Press MENU to display the menu.
(3) Select STILL SET in
(2) Press MENU to display the menu.
(3) Select STILL SET in
, then press EXEC (p. 179).
(4) Select IMAGESIZE, then press EXEC.
(5) Select a desired image size, then press EXEC.
(5) Select a desired image size, then press EXEC.
The indicator changes as follows:
1152
640
Memory capacity of still images
Recorded images are compressed in JPEG format before being stored in memory. The
memory capacity of still images varies depending on the selected image quality mode
and image size. Details are shown in the table below.
memory capacity of still images varies depending on the selected image quality mode
and image size. Details are shown in the table below.
1152
×
864 image size (DCR-TRV33 only)
Image quality
Memory capacity
FINE
About 500 KB
STANDARD
About 200 KB
640
×
480 image size
Image quality
Memory capacity
FINE
About 150 KB
STANDARD
About 60 KB
3
4
RET.
EXEC
R
r
EXIT
1152
MEM SET 1
STILL SET
BURST
QUALITY
IMAGESIZE
STILL SET
BURST
QUALITY
IMAGESIZE
1152
×
864
640
×
480
REMAIN
12
12
EXIT
RET.
EXEC
R
r
MEM SET 1
STILL SET
BURST
QUALITY
IMAGESIZE
STILL SET
BURST
QUALITY
IMAGESIZE
OFF
112
Selecting the moving picture size
You can select picture size 320
×
240 or 160
×
112.
The default setting is 320
×
240.
The POWER switch should be set to
or
.
Operate by touching the panel.
(1) Press FN to display PAGE1.
(2) Press MENU to display the menu.
(3) Select MOVIE SET in
(2) Press MENU to display the menu.
(3) Select MOVIE SET in
, then press EXEC (p. 179).
(4) Select IMAGESIZE, then press EXEC.
(5) Select a desired image size, then press EXEC.
(5) Select a desired image size, then press EXEC.
The indicator changes as follows:
320
160
To return to FN
Press EXIT.
Selecting image quality and size
3
4
EXIT
RET.
EXEC
R
r
MEM SET 1
MOVIE SET
IMAGESIZE
REMAIN
MOVIE SET
IMAGESIZE
REMAIN
320 240
REMAIN
30sec
320
EXIT
RET.
EXEC
R
r
MEM SET 1
MOVIE SET
IMAGESIZE
REMAIN
MOVIE SET
IMAGESIZE
REMAIN
320 240
160 112
160 112
REMAIN
30sec
Click on the first or last page to see other DCR-TRV12E / DCR-TRV14E / DCR-TRV19 / DCR-TRV19E (serv.man3) service manuals if exist.