Sony DCR-TRV12E / DCR-TRV14E / DCR-TRV19 / DCR-TRV19E (serv.man2) Service Manual ▷ View online
2-13
DCR-TRV12E/TRV14E/TRV19/TRV19E
2-12. LB-085 BOARD (REMOVING OF THE EVF)-2
2
Open the lock of the VF slide cabinet (lower) in the direction of the arrow
A
,
3
release the two claws of the VF slide cabinet (upper) assembly,
4
while slanting the VF slide cabinet (upper) in the direction of the arrow
B
,
5
remove the Visibility knob (40) from the VF slide cabinet (lower), and
6
remove the VF slide cabinet (upper) assembly by sliding it in the direction
of the arrow
C
.
2
2
A
A
B
C
4
6
5
2
Align the dotted portion of the VF slide assembly
with the dotted line of the VF slide cabinet (lower).
1
Tapping screw
(M1.7
×
3.5)
4
Tapping screw
(M1.7
×
3.5)
3
Two claws
1
VF slide assembly
VF slide cabinet (upper) assembly
VF slide cabinet (upper) assembly
To raise the VF slide cabinet (upper)
assembly, insert a flat head
(-) screwdriver into the position shown
by the arrow.
assembly, insert a flat head
(-) screwdriver into the position shown
by the arrow.
VF slide cabinet (upper) assembly
When re-assembling, slide the
Visibility knob (40) to the fully
right-end beforehand.
Visibility knob (40) to the fully
right-end beforehand.
3
Slide the VF slide cabinet assembly up to
the position in the direction of the arrow
where the two claws are locked.
where the two claws are locked.
RE-ASSEMBLING THE VF SLIDE CABINET
VF slide cabinet (lower)
VF slide cabinet (lower)
When re-assembling is completed,
the VF slide cabinet (upper) assembly
and the VF slide cabinet (lower) are
assembled as shown.
the VF slide cabinet (upper) assembly
and the VF slide cabinet (lower) are
assembled as shown.
VF slide cabinet (lower)
VF slide cabinet (lower)
Two claws
VF slide cabinet (lower)
Visiblity knob (40)
Visiblity knob (40)
2-14
DCR-TRV12E/TRV14E/TRV19/TRV19E
2-13. LB-085 BOARD (REMOVING OF THE EVF)-3
3
Slide the VF slide cabinet assembly and others once
to the deep end, then slant them in the direction of
the arrow
the arrow
A
to release the claw portion of the VF slide
assembly and finally pull them out in the direction of the
arrow
arrow
B
and remove them.
A
B
1
Two screws
(M1.7
×
2.5),
lock ace, p2
2
Pull out the VF slide assembly fully
in the direction of the arrow.
VF slide Cabinet (upper) assembly
VF slide assembly, etc.
qf
LCX032AN-5
qa
Lamp guide (40)
q;
Cushion LB (40)
8
FP-619 flexible board
7
Sheet (VF)
9
LB-085 board
Projected part
Two craws
Two craws
qs
Illuminator (40)
qd
Prism sheet (40)
Cut-outs
qg
LCD cabinet assembly
5
Screw
(M1.7
×
2.5),
lock ace, p2
6
Remove the LCD cabinet assembly and others from the two dowels and
cut-outs of the VF slide assembly.
4
Screw
(M1.7
×
2.5),
lock ace, p2
Two dowels
VF slide assembly
Flexible board of the
LCX032AN-5
LCX032AN-5
Caution
Sheet (VF)
When attach the Sheet (VF),
fold the flexible board of the
LCX032AN-5 as shown in
the illustration.
fold the flexible board of the
LCX032AN-5 as shown in
the illustration.
2-15
DCR-TRV12E/TRV14E/TRV19/TRV19E
2-14. VA-118 BOARD, LENS SECTION
q;
Lens section
6
Lens device LSV-650E (24P)
Flexible board of the
Lens device LSV-650E
Lens device LSV-650E
9
Screw
(M1.7
×
2.5),
lock ace, p2
2
Two screws
(M1.7
×
2.5),
lock ace, p2
5
VA-118 board,
FP-621 flexible board
1
Control switch block
(FK-CX4000) (3P)
8
Screw
(M1.7
×
2.5),
lock ace, p2
7
FP-623 flexible board
(14P)
4
FP-620 flexible board
(10P)
3
B to B connector
(100P)
Caution
FP-620 flexible
board
board
Caution
Tape (A)
When attach the Tape (A), fold the FP-620
flexible board as shown in the illustration.
flexible board as shown in the illustration.
Caution
When installing, the flexible board of the
Lens device 650E as shown in the illustration.
Lens device 650E as shown in the illustration.
Harness of the Control
switch block (FK-CX4000)
switch block (FK-CX4000)
Fold the harness of the control switch
block (FK-CX4000) toward the board as
shown in the illustration.
block (FK-CX4000) toward the board as
shown in the illustration.
2-16
DCR-TRV12E/TRV14E/TRV19/TRV19E
2-16. MECHANISM DECK, VC-311 BOARD (1)
2-15. CD-430 BOARD
q;
CD-430 board
8
CCD block
assembly
9
Remove soldering
4
Two tapping screws
(M1.7
×
5)
1
Two tapping screws
(M1.7
×
3.5)
3
FP-623 flexible board
(14P)
7
Seal rubber (W)
2
Lens frame (39) assembly
6
optical filter block
5
Lens device LSV-650E
8
Screw
9
Mechanism deck,
VC-311 board
7
Screw
(M1.7
×
4),
lock ace, p2
3
Screw
(M1.7
×
2.5),
lock ace, p2
4
Screw
(M1.7
×
2.5),
lock ace, p2
5
Screw
(M1.7
×
2.5),
lock ace, p2
1
Control switch block (FK-CX4000)
(12P)
6
Open the cassette lid
2
FP-625 flexible board
(16P)
Click on the first or last page to see other DCR-TRV12E / DCR-TRV14E / DCR-TRV19 / DCR-TRV19E (serv.man2) service manuals if exist.