Sony DCR-SR210E / DCR-SR220 / DCR-SR220D / DCR-SR220E / HDR-SR10 / HDR-SR10D / HDR-SR10E (serv.man2) Service Manual ▷ View online
2-1
2. DISASSEMBLY
DCR-SR210E/SR220/SR220D/SR220E/
HDR-SR10/SR10D/SR10E_L2
HDR-SR10/SR10D/SR10E_L2
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
DISCHARGING OF THE ST-189 BOARD’S CHARGING CAPACITOR (C5056)
The charging capacitor (C5056) of the ST-189 board is charged
up to the maximum 330 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
up to the maximum 330 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k
a resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
prevent electrical shock.
NOTE FOR DISCONNECTING THE HARNESS (HN-058)
When disconnecting the harness (HN-058), do not pull the
harness part but pull off the connector body with tweezers etc.
harness part but pull off the connector body with tweezers etc.
Harness
(HN-058)
(HN-058)
Tweezers etc.
1 k
Ω
/1 W
Wrap insulating tape.
C5056
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between the two points
with the short jig about 10 seconds.
Short-circuit between the two points
with the short jig about 10 seconds.
ST-189 Board
R:1 k
Ω
/1 W
(Part code: 1-215-869-11)
2-2
DCR-SR210E/SR220/SR220D/SR220E/
HDR-SR10/SR10D/SR10E_L2
HDR-SR10/SR10D/SR10E_L2
2-1. IDENTIFYING PARTS
2-2-1. OVERALL SECTION-1
- Cabinet (G) Assy
- HDD
- Bottom Cabinet Block
- HDD
- Bottom Cabinet Block
2-2-2. OVERALL SECTION-2
- Cabinet (R) Section
- Cabinet (Top) Block
- BT Panel Block
- Cabinet (Top) Block
- BT Panel Block
2-2-3. OVERALL SECTION-3
- Cabinet (F) Section
- VC-516 Board
- VC-516 Board
2-2-5. CABINET (F) SECTION
- Lens Block
- FR-285 Board
- Lens Barrier Unit
- FR-285 Board
- Lens Barrier Unit
2-2-6. LENS BLOCK
- ST-189 Board
- LD-230 Board
- Flash Unit
- LD-230 Board
- Flash Unit
2-2-7. CABINET (R) SECTION
- Loud Speaker
- CK-196 Board
- Panel Block
- CK-196 Board
- Panel Block
2-2-8. PANEL BLOCK
- Hinge Assy
- LCD
- PD-356 Board
- LCD
- PD-356 Board
- DISASSEMBLY FLOW -
2-2-4. CABINET (L) SECTION
- JK-366 Board
- Control Switch Block (PS28100)
- FP-855 Flexible Board
(HDR-SR10/SR10D/SR10E)
- Control Switch Block (PS28100)
- FP-855 Flexible Board
(HDR-SR10/SR10D/SR10E)
Cabinet (R) Section
⋅
CK-196 Board
⋅
PD-356 Board
Cabinet (L) Section
⋅
VC-516 Board
⋅
JK-366 Board
Cabinet (F) Section
⋅
FR-285 Board
⋅
ST-189 Board
⋅
LD-230 Board
BT Panel Block
⋅
MS-397 Board
Top Assy
Cabinet (Top)
Block Assy
Block Assy
Bottom Cabinet Block
⋅
CR-091 Board
2-3
DCR-SR210E/SR220/SR220D/SR220E/
HDR-SR10/SR10D/SR10E_L2
HDR-SR10/SR10D/SR10E_L2
2-2. DISASSEMBLY
2-2-1. OVERALL SECTION-1
Follow the disassembly in the numerical order given.
1
Cabinet (G) Assy (
1
-1 to
1
-7)
2
HDD (
2
-1 to
2
-3)
3
Bottom Cabinet Block (
3
-1 to
3
-2)
HELP
HELP
EXPLODED VIEW
HARDWARE LIST
1
Cabinet (G)
Assy
Overall Section-2
(See Page 2-4)
1
-5 (#2)
1
-4
(#2)
1
-1
(#2)
1
-2
(Claw)
1
-7 (#2)
1
-6
(Slide the
Jack Cover(G))
Jack Cover(G))
2
HDD
2
-3
2
-1
2
-2
3
Bottom Cabinet Block
DCR-
SR210E/
SR220/
SR220D/
SR220E
SR210E/
SR220/
SR220D/
SR220E
1
-3
3
-1 (#2)
3
-2
2-4
DCR-SR210E/SR220/SR220D/SR220E/
HDR-SR10/SR10D/SR10E_L2
HDR-SR10/SR10D/SR10E_L2
2-2-2. OVERALL SECTION-2
Follow the disassembly in the numerical order given.
1
Cabinet (R) Section (
1
-1 to
1
-8)
2
Cabinet (Top) Block (
2
-1 to
2
-10)
3
BT Panel Block (
3
-1 to
3
-4)
EXPLODED VIEW
HARDWARE LIST
3
BT Panel Block
1
-2
(#1)
2
-2 (#14)
2
-8
(#11)
2
-9
2
-10
2
-7
(#14)
2
-6
(#2)
2
-4
2
-1
(#2)
3
-1
(#2)
3
-2
3
-3
3
-4
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between the two points with the short jig
about 10 seconds. To avoid the spark with the metal
plate, wrap the short jig with the insulation tape.
Short-circuit between the two points with the short jig
about 10 seconds. To avoid the spark with the metal
plate, wrap the short jig with the insulation tape.
R:1 k
Ω
/1 W
(Part code: 1-215-869-11)
1
Cabinet (R)
Section
(See Page 2-9)
2
Cabinet (Top)
Block
1
-1
(Open the
LCD Panel)
LCD Panel)
1
-5 (#2)
1
-7
(#12)
1
-6
(#2)
1
-4
1
-8
2
-3
(Open the
Shoe Cover)
Shoe Cover)
2
-5 (#14)
HELP02
HELP01
C5056
(Charging
Capacitor)
(Charging
Capacitor)
ST-189
Board
Board
Overall
Section-3
Section-3
(See Page 2-5)
1
-3
(Claw)
Click on the first or last page to see other DCR-SR210E / DCR-SR220 / DCR-SR220D / DCR-SR220E / HDR-SR10 / HDR-SR10D / HDR-SR10E (serv.man2) service manuals if exist.