Sony DCR-SR210E / DCR-SR220 / DCR-SR220D / DCR-SR220E / HDR-SR10 / HDR-SR10D / HDR-SR10E (serv.man2) Service Manual ▷ View online
1-4
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DCR-SR210E/SR220/SR220D/SR220E/
HDR-SR10/SR10D/SR10E_L2
HDR-SR10/SR10D/SR10E_L2
1-3-2. E : 62 : 11 [Shift Lens Overheating (Pitch)] Occurred
Connect by the SeusEX and perform the following process.
Order Block Page Address Data
Procedure
1
11
80
7430
01
Write the data. (After it starts, set it before caution is displayed.)
2
11
8E
F946
F0
Write the data.
3
11
8E
F948
01
Write the data. (Note 1)
4
11
8E
F948
00
Write the data.
5
11
8E
F946
10
Write the data.
6
11
8E
F948
01
Write the data. (Note 1)
7
11
8E
F948
00
Write the data.
8
11
80
7430
00
Write the data.
9
Check if the shift lens moves while setting the order 2 to 7. If the shift lens does not move,
replace the lens block (Note 2). When the shift lens moved, proceed to the order 10.
replace the lens block (Note 2). When the shift lens moved, proceed to the order 10.
10
While setting the order 2 to 7, measure with an oscilloscope the output voltage of R5526 in the
periphery of IC5501 on the LD-230 board to check the output voltage varies.
periphery of IC5501 on the LD-230 board to check the output voltage varies.
11
If the output voltage does not vary, replace the lens block (Note 2). When the output voltage
varied, proceed to the order 12.
varied, proceed to the order 12.
12
Turn the power OFF.
While measuring with an oscilloscope the output voltage of R5549 in the periphery of IC5501
13
on the LD-230 board, turn the power ON to check that the output voltage immediately after the
power on change as shown in Fig. 2.
power on change as shown in Fig. 2.
If the output voltage change as shown in Fig. 2, replace the lens block (Note 2). If it does not
14
change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-516 board) pe
riphery.
riphery.
Note 1: Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set block: 11, page: 8E, address:
F948, data: 00, and then retry.
Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
handheld operation.
1-5
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DCR-SR210E/SR220/SR220D/SR220E/
HDR-SR10/SR10D/SR10E_L2
HDR-SR10/SR10D/SR10E_L2
1-3-3. E : 62 : 12 [Shift Lens Overheating (Yaw)] Occurred
Connect by the SeusEX and perform the following process.
Order Block Page Address Data
Procedure
1
11
80
7430
01
Write the data. (After it starts, set it before caution is displayed.)
2
11
8E
F947
F0
Write the data.
3
11
8E
F949
01
Write the data. (Note 1)
4
11
8E
F949
00
Write the data.
5
11
8E
F947
10
Write the data.
6
11
8E
F949
01
Write the data. (Note 1)
7
11
8E
F949
00
Write the data.
8
11
80
7430
00
Write the data.
9
Check if the shift lens moves while setting the order 2 to 7. If the shift lens does not move,
replace the lens block (Note 2). When the shift lens moved, proceed to the order 10.
replace the lens block (Note 2). When the shift lens moved, proceed to the order 10.
10
While setting the order 2 to 7, measure with an oscilloscope the output voltage of R5534 in the
periphery of IC5501 on the LD-230 board to check the output voltage varies.
periphery of IC5501 on the LD-230 board to check the output voltage varies.
11
If the output voltage does not vary, replace the lens block (Note 2). When the output voltage
varied, proceed to the order 12.
varied, proceed to the order 12.
12
Turn the power OFF.
While measuring with an oscilloscope the output voltage of R5549 in the periphery of IC5501
13
on the LD-230 board, turn the power ON to check that the output voltage immediately after the
power on change as shown in Fig. 2.
power on change as shown in Fig. 2.
If the output voltage change as shown in Fig. 2, replace the lens block (Note 2). If it does not
14
change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-516 board)
periphery.
periphery.
Note 1: Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set block: 11, page: 8E, address:
F949, data: 00, and then retry.
Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
handheld operation.
1-3-4. E : 62 : 20 [Abnormality of Thermistor] Occurred
Order
Procedure
1
Turn the power ON.
2
Confirm the connections of flexible flat cables and connectors between the lens block and LD-230 board, LD-230 board and
VC-516 board.
VC-516 board.
3
In case of no malfunction of connections, replace the lens block with new one. (Note) When the error has occurred in spite of the
lens replacement, replace LD-230 board with new one.
lens replacement, replace LD-230 board with new one.
Note: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
handheld operation.
1-6
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DCR-SR210E/SR220/SR220D/SR220E/
HDR-SR10/SR10D/SR10E_L2
HDR-SR10/SR10D/SR10E_L2
1-4. PRECAUTION ON REPLACING THE VC-516 BOARD
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Refer to Service Manual ADJ, and perform “DESTINATION DATA WRITE”.
Refer to Service Manual ADJ, and perform “DESTINATION DATA WRITE”.
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Refer to Service Manual ADJ, and perform “USB SERIAL No. INPUT”.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Refer to Service Manual ADJ, and perform “USB SERIAL No. INPUT”.
1-7
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DCR-SR210E/SR220/SR220D/SR220E/
HDR-SR10/SR10D/SR10E_L2
HDR-SR10/SR10D/SR10E_L2
1-2. 自己診断機能
1-2-1.自己診断機能について
本機の動作に不具合が生じたとき，自己診断機能が働き，
L C D 画面に，どう処置したらよいか判断できる表示を行い
L C D 画面に，どう処置したらよいか判断できる表示を行い
ます。「自己診断表示」と「サービスモード表示」の２つの表
示があります。自己診断機能については取扱説明書にも掲載
示があります。自己診断機能については取扱説明書にも掲載
されています。
1-2-2.自己診断表示
本機の動作に不具合が生じたとき，LCD画面のカウンタ表示
部分がアルファベットと数字の4桁表示になり，3.2Hzで点
部分がアルファベットと数字の4桁表示になり，3.2Hzで点
滅します。この5 文字の表示によって対応者分類および不具
合の生じたブロックの分類，不具合の詳細コードを示しま
合の生じたブロックの分類，不具合の詳細コードを示しま
す。
1. SERVICE NOTE
1-1. 修理時の電源供給について
本機では，安定化電源（8.4Vdc）からバッテリ端子に電源を供給した場合，約10秒後にシャットオフし，動作しなくなります。
これを避けるため，下記の方法を用いてください。
方法：
DC入力端子を使用する。（ACアダプタ（AC-L200/L200Bなど）を使用する。）
DC入力端子を使用する。（ACアダプタ（AC-L200/L200Bなど）を使用する。）
1 1
3 1
C
対応者分類
「1-2-3.
自己診断コード表」
を参照
対応方法の違いにより分類
例 31･･･テープを入れ直す
例 31･･･テープを入れ直す
32･･･電源を入れ直す
ブロック分類
詳細コード
3.2Hz点滅
C
：お客さま自身で対応
H ：販売店で対応
E ：サービスエンジニア
H ：販売店で対応
E ：サービスエンジニア
で対応
LCD画面
C : 3 1 : 1 1
Click on the first or last page to see other DCR-SR210E / DCR-SR220 / DCR-SR220D / DCR-SR220E / HDR-SR10 / HDR-SR10D / HDR-SR10E (serv.man2) service manuals if exist.