Sony DCR-PC110 / DCR-PC110E (serv.man4) Service Manual ▷ View online
5-4
J-1
J-2
J-6
J-3
J-7
J-8
J-4
J-5
Fig. 5-1-1.
J-9
J-10
J-11
Ref. No.
J-1
J-2
J-3
J-4
J-5
J-6
J-7
J-8
J-9
J-10
J-11
J-12
Name
Filter for color temperature correction (C14)
ND filter 1.0
ND filter 0.4
ND filter 0.1
Pattern box PTB-450
Color chart for pattern box
Adjustment remote commander (RM-95 upgraded).
(Note 1)
(Note 1)
Siemens star chart
Clear chart for pattern box
CPC-8 jig
IR receiver jig
Mini pattern box
Camera table
Background paper
Parts Code
J-6080-058-A
J-6080-808-A
J-6080-806-A
J-6080-807-A
J-6082-200-A
J-6020-250-A
J-6082-053-B
J-6080-875-A
J-6080-621-A
J-6082-388-A
J-6082-383-A
J-6082-353-B
J-6082-384-A
J-2501-130-A
Usage
Auto white balance adjustment/check
White balance adjustment/check
White balance adjustment/check
White balance check
White balance check
White balance check
For checking the flange back
For adjusting the video section
For adjusting the color viewfinder
For adjusting the color viewfinder
For adjusting the IR transmitter
For adjusting the flange back
For adjusting the flange back
For strobe adjustments
5-1. CAMERA SECTION ADJUSTMENT
1-1.
PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION)
1-1-1.
List of Service Tools
• Oscilloscope
• Color monitor
• Vectorscope
• Regulated power supply
• Digital voltmeter
Note1:
If the microprocessor IC in the adjustment remote commander is
not the new microprocessor (UPD7503G-C56-12), the pages
cannot be switched. In this case, replace with the new
microprocessor (8-759-148-35).
not the new microprocessor (UPD7503G-C56-12), the pages
cannot be switched. In this case, replace with the new
microprocessor (8-759-148-35).
J-12
5-5
1-1-2.
Preparations
Note 1:
For details of how remove the cabinet and boards, refer to “2.
DISASSEMBLY”.
DISASSEMBLY”.
Note 2:
When performing only the adjustments, the lens block and boards
need not be disassembled.
need not be disassembled.
1)
Connect the equipment for adjustments according to Fig. 5-1-3.
Note 3:
As removing the cabinet (L) (removing CN1054 of AI-021 board)
means removing the lithium 3V power supply (BT1731), data such
as date, time, user-set menus will be lost. After completing
adjustments, reset these data. If the cabinet (L) has been removed,
the self-diagnosis data, data on history of use (total drum rotation
time etc.) will be lost. Before removing, note down the self-
diagnosis data (date of page: 2, address: B0 to C6) and the data
on history use (data of page: 2, address: A2 to AA). (Refer to
“SELF-DIAGNOSIS FUNCTION” for the self-diagnosis data, and
to “5-4.Service Mode” for the data on the history use.)
means removing the lithium 3V power supply (BT1731), data such
as date, time, user-set menus will be lost. After completing
adjustments, reset these data. If the cabinet (L) has been removed,
the self-diagnosis data, data on history of use (total drum rotation
time etc.) will be lost. Before removing, note down the self-
diagnosis data (date of page: 2, address: B0 to C6) and the data
on history use (data of page: 2, address: A2 to AA). (Refer to
“SELF-DIAGNOSIS FUNCTION” for the self-diagnosis data, and
to “5-4.Service Mode” for the data on the history use.)
Note 4:
Setting the “Forced Camera Power ON” Mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the PAUSE
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the PAUSE
button of the adjustment remote commander.
The above procedure will enable the camera power to be turned
on with the cabinet (L) assembly (FK-30550, PS-30550) removed.
After completing adjustments, be sure to exit the “Forced Camera
Power ON Mode”.
on with the cabinet (L) assembly (FK-30550, PS-30550) removed.
After completing adjustments, be sure to exit the “Forced Camera
Power ON Mode”.
Note 5:
Exiting the “Forced Camera Power ON” Mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE
button of the adjustment remote commander.
3) Select page: 0, address: 01, and set data: 00.
Fig. 5-1-2
Pattern box
1.5 m
Front of the lens
5-6
Fig. 5-1-3
FLASH UNIT
(30550MC)
PANEL
OPEN SW
OPEN SW
Cabinet (L)
Cabinet (R)
CN1401
CN1402
CN051
CN257
CN951
CN261
CN256
CN253
CN263
CN254
CN266
CN260
CN259
CN651
CN1332
CN1331
J1332
CN1336
CN1335
CN1334
CN1333
CN1054
Audio R
(Red)
Audio L
(White)
VIDEO
(Yellow)
AUDIO/VIDEO
jack
Terminated at
75
Ω
Color monitor
Vector scope
VF-147 board
Need not be
connected.
connected.
Need not be
connected.
connected.
CPC-8 jig
adjustment remote commander
Must be connected when performing
the video section adjustments or
color EVF system adjustment.
the video section adjustments or
color EVF system adjustment.
Must be connected.
AI-021 board
VC-253 board
FJ-027 board
Battery terminal
Must be connected when performing
the color EVF adjustments.
the color EVF adjustments.
Must be
connected
when using
the function
switch or
flash.
connected
when using
the function
switch or
flash.
Must be connected
when performing
the LCD system
adjustments.
when performing
the LCD system
adjustments.
Must be connected.
AC power adaptor
DC IN jack
LANC jack
(J-6082-388-A)
USB jack
AC-L10 or
AC-VQ800
AC-VQ800
5-7
1-1-3.
Precaution
1. Setting the Switch
Unless otherwise specified, set the switches as follows and perform
adjustments without loading cassette.
adjustments without loading cassette.
1.
POWER switch (PS-30550 block) ......................... CAMERA
2.
NIGHT SHOT switch (Lens block) ................................. OFF
3.
DEMO MODE (Menu setting) ........................................ OFF
4.
DIGITAL ZOOM (Menu setting) .................................... OFF
5.
STEADY SHOT (Menu setting) ...................................... OFF
6.
PROGRAM AE (Menu setting) ................................... AUTO
7.
WHITE BALANCE (Menu setting) ............................ AUTO
8.
16 : 9 WIDE (Menu setting) ............................................ OFF
9.
PICTURE EFFECT (Menu setting) ................................. OFF
10. DISPLAY (Menu setting) .................................. V-OUT/LCD
11. DISPLAY (ME-30550 block) ........................................... ON
12. FOCUS switch (FK-30550 block) ........................ MANUAL
13. DIGITAL EFFECT (ME-30550 block) ........................... OFF
11. DISPLAY (ME-30550 block) ........................................... ON
12. FOCUS switch (FK-30550 block) ........................ MANUAL
13. DIGITAL EFFECT (ME-30550 block) ........................... OFF
2. Order of Adjustments
Basically carry out adjustments in the order given.
Fig.5-1-4.
3. Subjects
1)
Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 5-1-4. (Color reproduction
adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 5-1-4. (Color reproduction
adjustment frame)
2)
Clear chart (Color reproduction adjustment frame)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during
this time.)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during
this time.)
3)
Flange back adjustment chart
Make the chart shown in Fig. 5-1-5 using A0 size (1189mm
Make the chart shown in Fig. 5-1-5 using A0 size (1189mm
×
841mm) black and white vellum paper.
H
A=B
C=D
A B
B
C
D
A
Enlargement
V
Electronic beam scanning frame
CRT picture frame
B
A
Difference in level
Y
ello
w
Cy
an
Green
White
Magenta
Red
Blue
Y
ello
w
Cy
an
Green
White
Magenta
Red
Blue
Color bar chart (Color reproduction adjustment frame )
Fig. a
(Video output terminal
output waveform)
Fig. b (TV monitor picture)
Adjust the camera zoom and direction to
obtain the output waveform shown in Fig. a
and the TV monitor display shown in Fig. b.
obtain the output waveform shown in Fig. a
and the TV monitor display shown in Fig. b.
White
Black
841mm
1189mm
Fig. 5-1-5.
Note:
Use matte vellum paper bigger than A0, and make sure the edges of
the black and white paper joined together are not rough.
the black and white paper joined together are not rough.
Click on the first or last page to see other DCR-PC110 / DCR-PC110E (serv.man4) service manuals if exist.