Sony DCR-PC103E / DCR-PC104E / DCR-PC105 / DCR-PC105E (serv.man2) Service Manual ▷ View online
2-23
DCR-PC103E/PC104E/PC105/PC105E
2-29. MECHANISM DECK (Z100)
1
Flip over the VC heat
insulation sheet
2
Four screws
(M1.4
×
1.5)
3
Open the G frame
assembly
A
B
4
Three dowels
Caution
Caution
Be careful not to
break the flexible board.
break the flexible board.
Be careful not to touch the
portion
portion
B
of the mechanism
deck.
5
Remove the mechanism deck
in the direction of the arrow
A
.
2-24
DCR-PC103E/PC104E/PC105/PC105E
Note: When the flash error code (E: 91: **) is displayed. After completion of “VTR check”,
clear the error flag in the following method.
clear the error flag in the following method.
(To eject a cassette, connect
the control switch block.
(PS4400))
the control switch block.
(PS4400))
VC-
319
AC IN
[SERVICE POSITION TO CHECK THE VTR SECTION]
Connection to Check the VTR Section
Connection to Check the VTR Section
To check the VTR section, set the VTR to the "Forced VTR power ON" mode.
Operate the VTR functions using the adjustment remote commander (with the HOLD switch set in the OFF position).
Operate the VTR functions using the adjustment remote commander (with the HOLD switch set in the OFF position).
Setting the “Forced VTR Power ON” mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: D, address: 10, set data: 02, and press the
PAUSE button of the adjustment remote commander.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: D, address: 10, set data: 02, and press the
PAUSE button of the adjustment remote commander.
Exiting the “Forced VTR Power ON” mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: D, address: 10, set data: 00, and press the
PAUSE button of the adjustment remote commander.
4) Select page: 0, address: 01, and set data: 00.
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: D, address: 10, set data: 00, and press the
PAUSE button of the adjustment remote commander.
4) Select page: 0, address: 01, and set data: 00.
1) Select page: 0, address: 10, and set data: 00.
2) Select page: 7, address: 00, and set data: 80.
3) Select page: 7, address: 01, set data: 80 and press the PAUSE button.
4) Check that the data of page: 7, address: 02 is “01”.
2) Select page: 7, address: 00, and set data: 80.
3) Select page: 7, address: 01, set data: 80 and press the PAUSE button.
4) Check that the data of page: 7, address: 02 is “01”.
AC power
adaptor
adaptor
LANC jack
DC IN jack
BJ-004 board
VF-156 board
VC-319 board
Adjustment remote
commander (RM-95)
commander (RM-95)
Control switch block
(PS4400)
(PS4400)
CPC-6 jig
(J-6082-371-A)
(J-6082-371-A)
CPC-6
flexible
jig
(J-6082-370-C)
Monitor TV
Mechanism deck
CN1015
CN2501
CN1801
CN1018
(CPC)
(CPC)
CN1012
CN2503
CN2502
CN1009
19
20
2
1
1
2-2. CABINET (FRONT) ASSEMBLY .....................
2
2-3. CABINET (G) ASSEMBLY...............................
3
2-4.
CABINET (L)....................................................
4
2-5.
ST CABINET (UPPER) ASSEMBLY................
5
2-6.
CABINET (R) SECTION..................................
6
2-7.
BATTERY HOLDER.........................................
7
2-8.
BJ-004 BOARD................................................
8
2-13. CABINET (REAR)..........................................
9
2-14. CONTROL SWITCH BLOCK (PS4400).........
0
2-15. ST-084 BOARD (PC105/PC105E).................
qa
2-16. LENS/EVF/ST SECTION-1............................
(page 2-3)
(page 2-3)
(page 2-4)
(page 2-4)
(page 2-5)
(page 2-6)
(page 2-7)
(page 2-11)
(page 2-12)
(page 2-12)
(page 2-13)
qs
2-17. LENS/EVF/ST SECTION-2................................
qd
2-18. EVF SECTION...................................................
qf
2-25. HR RETAINER ASSEMBLY,
MEMORY STICK CONNECTOR
(PC105/PC105E)...............................................
(PC105/PC105E)...............................................
qg
2-26. CONTROL SWITCH BLOCK (FK4400).............
qh
2-27. NS-018 BOARD, FK FRAME ASSEMBLY.........
qj
2-28. VC-319 BOARD.................................................
qk
2-29. MECHANISM DECK (Z100)..............................
(page 2-13)
(page 2-14)
(page 2-20)
(page 2-21)
(page 2-22)
(page 2-22)
(page 2-23)
PROCEDURE OF REMOVING THE MECHANISM DECK.
(VTR CHECK SERVICE POSITION)
(VTR CHECK SERVICE POSITION)
2-25
DCR-PC103E/PC104E/PC105/PC105E
2-30. CIRCUIT BOARDS LOCATION
ST-084
(PC105/PC105E)
(PC105/PC105E)
LI-070
NS-018
VC-319
VF-156
BJ-004
CD-444
PD-193
BJ-004
CD-444
LI-070
NS-018
PD-193
PD-193
ST-084
(PC105/PC105E)
VC-319
VF-156
NAME
FUNCTION
JACK
CCD IMAGER
BATTERY
SIRCS, NS
LCD RGB DRIVER
CCD IMAGER
BATTERY
SIRCS, NS
LCD RGB DRIVER
FLASH DRIVER
TIMING GENERATOR, S/H, AGC, A/D, CAMERA PROCESS, LENS DRIVE, MPEG MOVIE/
DV STILL/AUDIO DIGITAL STILL CONTROL, DIGITAL STILL CONTROL, HI CONTROL,
SDRAM/FLASH MEMORY, DV SIGNAL PROCESSOR, RF SIGNAL PROCESSOR, DV
INTERFACE, REC/PB AMP, VIDEO IN/OUT, AGC, CAPSTAN/DRUM/LD MOTOR DRIVE,
HI CONTROL, MECHA CONTROL, CAMERA CONTROL, EVF RGB DRIVER,TIMING
GENERATOR, AUDIO I/O,A/D,D/A CONVERTER, CHARGE SWITCH, DC/DC
CONVERTER, REGURATOR, CONNECTOR
MIC AMP, JACK
DV STILL/AUDIO DIGITAL STILL CONTROL, DIGITAL STILL CONTROL, HI CONTROL,
SDRAM/FLASH MEMORY, DV SIGNAL PROCESSOR, RF SIGNAL PROCESSOR, DV
INTERFACE, REC/PB AMP, VIDEO IN/OUT, AGC, CAPSTAN/DRUM/LD MOTOR DRIVE,
HI CONTROL, MECHA CONTROL, CAMERA CONTROL, EVF RGB DRIVER,TIMING
GENERATOR, AUDIO I/O,A/D,D/A CONVERTER, CHARGE SWITCH, DC/DC
CONVERTER, REGURATOR, CONNECTOR
MIC AMP, JACK
2-26E
DCR-PC103E/PC104E/PC105/PC105E
2-31. FLEXIBLE BOARDS LOCATION
FP-672
FP-671
FP-697
CONTROL SWITCH BLOCK
(PS4400)
(PS4400)
CONTROL SWITCH BLOCK
(FK4400)
(FK4400)
FLASH UNIT
(PC105/PC105E)
(PC105/PC105E)
Click on the first or last page to see other DCR-PC103E / DCR-PC104E / DCR-PC105 / DCR-PC105E (serv.man2) service manuals if exist.