Sony DCR-HC30 / DCR-HC30E (serv.man4) Service Manual ▷ View online
6-18
DCR-HC30/HC30E
5. 1F Page Table
Note1:
When reading or writing the 1F page data, select page: 0, address:
10, and set data: 01, then select F page. The 1F page can be chosen
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
10, and set data: 01, then select F page. The 1F page can be chosen
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
Note2:
Fixed data-1: Initialized data. (Refer to “1. Initializing the E, F, 1F
Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of E, F,
1F Page Data”).
Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of E, F,
1F Page Data”).
Address
Remark
Initial value
Address
Remark
Initial value
00 to 1B
1C
1D
1E
1F
20 to 61
62
63 to 72
73
74
75 to 82
83
84
85
86
87
88
89
8A
8B
8C
8D
8E to 93
94
95 to 96
97
98 to A9
AA
AB
AC
AD
AE
AF
B0
B1
B2
B3
B4 to FF
00
00
00
00
Fixed data-1
Emergency memory address
(Camera section)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Table. 6-1-13.
6-19
DCR-HC30/HC30E
1-3.
CAMERA SYSTEM ADJUSTMENTS
Before perform the camera system adjustments (except for “36MHz
Origin Oscillation Adjustment”), check that the specified values of
“VIDEO SYSTEM ADJUSTMENTS” are satisfied.
And check that the data of page: 0, address: 10 is “00”. If not, set
data: 00 to this address.
Origin Oscillation Adjustment”), check that the specified values of
“VIDEO SYSTEM ADJUSTMENTS” are satisfied.
And check that the data of page: 0, address: 10 is “00”. If not, set
data: 00 to this address.
1. 36MHz Origin Oscillation Adjustment (VC-351 board)
Set the frequency of the clock for synchronization.
If deviated, the synchronization will be disrupted and the color will
become inconsistent.
If deviated, the synchronization will be disrupted and the color will
become inconsistent.
Subject
Not required
Measurement Point
Pin qs of IC4001
Measuring Instrument
Frequency counter
Adjustment Page
F
Adjustment Address
10
Specified Value
f=18000000 ± 90Hz
Note:
The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
F
10
Change the data and set the
frequency (f) to the specified value.
frequency (f) to the specified value.
3
F
10
Press PAUSE button.
4
0
01
00
Set the data.
VC-351 board
IC4001
1
12
36
25
13
24
48
37
2. HALL Adjustment
For detecting the position of the lens iris and ND filter, adjust AMP
gain and offset.
gain and offset.
Subject
Not required
Measurement Point
Display data of page 1 (Note1)
Measuring Instrument
Adjustment remote commander
Adjustment Page
F
Adjustment Address
12 to 17
Specified Value 1
15 to 19
Specified Value 2
87 to 8B
Note1:
Displayed data of page 1 of the adjustment remote commander.
1 : 00 : XX
IRIS display data
Note2:
The data of page: 0, address: 10 must be “00”.
Note3:
Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
6, address: 01, set data: 00, and press the PAUSE button.
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
6
94
17
Set the data.
3
6
95
89
Set the data.
4
6
D0
60
Set the data.
5
6
D1
90
Set the data.
6
6
01
6D
Set the data, and press PAUSE
button.
button.
7
6
02
Check that the data changes to
“01”. (Note4)
“01”. (Note4)
8
6
01
00
Set the data, and press PAUSE
button.
button.
Note4:
The adjustment data will be automatically input to page: F, address:
12 to 17.
12 to 17.
Checking method:
Order Page Address Data
Procedure
1
0
03
03
Set the data.
2
6
01
01
Set the data, and press PAUSE
button.
button.
3
1
Check that the IRIS display data
(Note1) satisfies the specified
value 1.
(Note1) satisfies the specified
value 1.
4
6
01
03
Set the data, and press PAUSE
button.
button.
5
1
Check that the IRIS display data
(Note1) satisfies the specified
value 2.
(Note1) satisfies the specified
value 2.
Processing after Completing Adjustments:
Order Page Address Data
Procedure
1
6
94
00
Set the data.
2
6
95
00
Set the data.
3
6
01
00
Set the data, and press PAUSE
button.
button.
4
0
03
00
Set the data.
5
0
01
00
Set the data.
Fig. 6-1-6.
6-20
DCR-HC30/HC30E
3. Flange Back Adjustment (Using Minipattern Box)
The inner focus lens flange back adjustment is carried out
automatically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.
automatically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.
Subject
Siemens star chart with ND filter for
the minipattern box (Note1)
the minipattern box (Note1)
Measuring Instrument
Adjustment remote commander
Adjustment Page
F
Adjustment Address
44 to 54
Note1:
Dark Siemens star chart.
Note2:
This adjustment should be carried out upon completion of “HALL
Adjustment”.
Adjustment”.
Note3:
Make the lens horizontal and perform this adjustment.
Note4:
The data of page: 0, address: 10 must be “00”.
Note5:
Check that the data of page: 6, address: 02 is “00”. If not, turn off
the power and turn on again.
the power and turn on again.
Switch setting:
1)
1)
MODE ......................................................... CAMERA-TAPE
2)
NIGHT SHOT .................................................................. OFF
Preparations:
1)
1)
The minipattern box is installed as shown in the following
figure.
figure.
Note:
The attachment lenses are not used.
2)
Install the minipattern box so that the distance between it and
the front of the lens of the camcorder is less than 3cm.
the front of the lens of the camcorder is less than 3cm.
3)
Make the height of the minipattern box and the camcorder equal.
4)
Check that the output voltage of the regulated power supply is
the specified voltage.
the specified voltage.
5)
Check that at both the zoom lens TELE end and WIDE end,
the center of the Siemens star chart and center of the exposure
screen coincide.
the center of the Siemens star chart and center of the exposure
screen coincide.
Specified voltage:
The specified voltage varies according to the minipattern box, so
adjust the power supply output voltage to the specified voltage
written on the sheet which is supplied with the minipattern box.
The specified voltage varies according to the minipattern box, so
adjust the power supply output voltage to the specified voltage
written on the sheet which is supplied with the minipattern box.
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
6
48
01
Set the data.
3
6
01
13
Set the data, and press PAUSE
button. (Note3)
button. (Note3)
4
6
01
27
Set the data, and press PAUSE
button.
button.
5
6
02
Check that the data changes to
“01”. (Note6)
“01”. (Note6)
Note6:
The adjustment data will be automatically input to page: F, address:
44 to 54.
44 to 54.
Processing after Completing Adjustments:
Order Page Address Data
Procedure
1
6
48
00
Set the data.
2
6
01
00
Set the data, and press PAUSE
button.
button.
3
6
01
25
Set the data, and press PAUSE
button.
button.
4
6
01
00
Set the data, and press PAUSE
button.
button.
5
0
01
00
Set the data.
6
Perform “Flange Back Check”.
Minipattern box
Below 3 cm
Camcorder
Camera
table
Red (+)
Black (–)
Yellow (SENS +)
White (SENS –)
Black (GND)
Need not connected
Regulated power supply
Output voltage : Specified voltage
±
0.01Vdc
Output current : more than 3.5A
Fig. 6-1-7.
6-21
DCR-HC30/HC30E
4. Flange Back Adjustment (Using Flange Back
Adjustment Chart and Subject More Than 500m Away)
The inner focus lens flange back adjustment is carried out
automatically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.
automatically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.
4-1. Flange Back Adjustment (1)
Subject
Flange back adjustment chart
(2.0 m from the front of the protection
glass) (Luminance: 350 ± 50 lux)
(2.0 m from the front of the protection
glass) (Luminance: 350 ± 50 lux)
Measuring Instrument
Adjustment remote commander
Adjustment Page
F
Adjustment Address
44 to 54
Note1:
This adjustment should be carried out upon completion of “HALL
Adjustment”.
Adjustment”.
Note2:
Make the lens horizontal and perform this adjustment.
Note3:
The data of page: 0, address: 10 must be “00”.
Note4:
Check that the data of page: 6, address: 02 is “00”. If not, turn off
the power and turn on again.
the power and turn on again.
Switch setting:
1)
1)
MODE ......................................................... CAMERA-TAPE
2)
NIGHT SHOT .................................................................. OFF
Preparations:
1)
1)
Check that at both the zoom lens TELE end and WIDE end,
the center of the chart for the flange back adjustment and center
of the exposure screen coincide.
the center of the chart for the flange back adjustment and center
of the exposure screen coincide.
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
6
48
01
Set the data.
3
6
01
13
Set the data, and press PAUSE
button. (Note2)
button. (Note2)
4
6
01
15
Set the data, and press PAUSE
button.
button.
5
6
02
Check that the data changes to
“01”. (Note5)
“01”. (Note5)
Note5:
The adjustment data will be automatically input to page: F, address:
44 to 54.
44 to 54.
Processing after Completing Adjustments:
Order Page Address Data
Procedure
1
6
01
00
Set the data, and press PAUSE
button.
button.
2
6
01
25
Set the data, and press PAUSE
button.
button.
3
6
01
00
Set the data, and press PAUSE
button.
button.
4
Perform “Flange Back
Adjustment (2)”.
Adjustment (2)”.
4-2.
Flange Back Adjustment (2)
Perform this adjustment after performing “Flange Back Adjustment
(1)”.
(1)”.
Subject
Subject more than 500m away
(Subjects with clear contrast such as
buildings, etc.)
(Subjects with clear contrast such as
buildings, etc.)
Measurement Point
Check operation on TV monitor
Measuring Instrument
Adjustment Page
F
Adjustment Address
44 to 54
Note1:
Make the lens horizontal and perform this adjustment.
Note2:
The data of page: 0, address: 10 must be “00”.
Note3:
Check that the data of page: 6, address: 02 is “00”. If not, turn off
the power and turn on again.
the power and turn on again.
Switch setting:
1)
1)
MODE ......................................................... CAMERA-TAPE
2)
NIGHT SHOT .................................................................. OFF
Preparations:
1)
1)
Set the zoom lens to the TELE end and expose a subject that is
more than 500m away (subject with clear contrast such as
building, etc.). (Nearby subjects less than 500m away should
not be in the screen.)
more than 500m away (subject with clear contrast such as
building, etc.). (Nearby subjects less than 500m away should
not be in the screen.)
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
6
48
01
Set the data.
3
6
01
13
Set the data, and press PAUSE
button. (Note2)
button. (Note2)
4
Place a ND filter on the lens so
that the optimum image is obtain.
that the optimum image is obtain.
5
6
01
29
Set the data, and press PAUSE
button.
button.
6
6
02
Check that the data changes to
“01”. (Note4)
“01”. (Note4)
Note4:
The adjustment data will be automatically input to page: F, address:
44 to 54.
44 to 54.
Processing after Completing Adjustments:
Order Page Address Data
Procedure
1
6
48
00
Set the data.
2
6
01
00
Set the data, and press PAUSE
button.
button.
3
6
01
25
Set the data, and press PAUSE
button.
button.
4
6
01
00
Set the data, and press PAUSE
button.
button.
5
0
01
00
Set the data.
6
Perform “Flange Back Check”.
Click on the first or last page to see other DCR-HC30 / DCR-HC30E (serv.man4) service manuals if exist.