Sony DCR-HC28 (serv.man3) Service Manual ▷ View online
6-23
DCR-HC28_ADJ
Processing after completing adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE (Write) button.
2
6
9D
00
3
0
01
00
8.
Color Reproduction Adjustment
Adjust the color separation matrix coefficient so that proper color
reproduction is produced.
reproduction is produced.
Subject
Color bar chart
(Color reproduction adjustment
frame)
(Color reproduction adjustment
frame)
Measurement Point
Video terminal of A/V OUT jack (75
Ω
terminated)
Measuring Instrument
Vectorscope
Adjustment Page
F
Adjustment Address
33, 35, 3A, 3B
Specified Value
All color luminance points should
settle within each color reproduction
frame.
settle within each color reproduction
frame.
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Note 2:
Perform “Flange Back Adjustment” and “F No. Standard
Data Input” before this adjustment.
Data Input” before this adjustment.
Note 3:
NTSC model: DCR-HC28
PAL model: DCR-HC27E/HC28E
PAL model: DCR-HC27E/HC28E
Switch setting:
1) POWER ......................................................... CAMERA mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
1) POWER ......................................................... CAMERA mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
Adjusting method:
Order Page Address Data
Procedure
1
Check that the picture frame
is “Color Reproduction
Adjustment Frame”. If not,
perform “6. Picture Frame
Setting (Color Reproduction
Adjustment Frame) ”
is “Color Reproduction
Adjustment Frame”. If not,
perform “6. Picture Frame
Setting (Color Reproduction
Adjustment Frame) ”
2
0
01
01
3
6
9D
83
4
6
01
3D
Press PAUSE (Write) button.
5
F
80
Set the following data, and
press PAUSE (Write) button.
press PAUSE (Write) button.
77: NTSC model
F7: PAL model
F7: PAL model
6
Adjust the GAIN and PHASE
of the vectorscope, and set to
the burst luminance point to
the burst position of color re-
production frame.
of the vectorscope, and set to
the burst luminance point to
the burst position of color re-
production frame.
7
F
Change the data and settle each
color luminance point in each
color reproduction frame.
(Note 4)
color luminance point in each
color reproduction frame.
(Note 4)
Note 4:
Be sure to press the PAUSE (Write) button of the adjust-
ing remote commander before changing the addresses.
If not, the new data will not be written to the memory.
ing remote commander before changing the addresses.
If not, the new data will not be written to the memory.
NTSC model
PAL model
33
35
35
3A
3B
3B
Fig. 6-1-14
R-Y
B-Y
R
B
G
M
G
Y
E
C
Y
Burst
position
position
R-Y
B-Y
R
B
G
M
G
Y
E
C
Y
Burst
position
position
6-24
DCR-HC28_ADJ
10. LV Standard Data Input
RadarW
RadarW
RadarW
RadarW
RadarW
Adjust the normal coefficient of the light value.
Subject
Clear chart
(Color reproduction adjustment frame)
(Color reproduction adjustment frame)
Measuring Instrument
Adjusting remote commander
Adjustment Page
F
Adjustment Address
1A, 1B
Note 1:
Perform “Flange Back Adjustment” and “F No. Standard
Data Input” before this adjustment.
Data Input” before this adjustment.
Note 2:
Check that the data of page: 0, address: 10 is “00”.
Note 3:
Check that the data of page: 6, address: 02 is “00”.
If not, select page: 6, address: 01, set data: 00, and press
the PAUSE (Write) button.
If not, select page: 6, address: 01, set data: 00, and press
the PAUSE (Write) button.
Switch setting:
1) POWER ......................................................... CAMERA mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
1) POWER ......................................................... CAMERA mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
Adjusting method:
Order Page Address Data
Procedure
1
Check that the picture frame
is “Color Reproduction
Adjustment Frame”. If not,
perform “6. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”.
is “Color Reproduction
Adjustment Frame”. If not,
perform “6. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”.
2
0
01
01
3
6
01
0D
Press PAUSE (Write) button.
(Note 4)
(Note 4)
4
6
02
Check the data changes to
“01”.
“01”.
Note 4:
The adjustment data will be automatically input to page:
F, address: 1A and 1B.
F, address: 1A and 1B.
Processing after completing adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE (Write) button.
2
0
01
00
9.
Auto White Balance Standard Data Input
RadarW
RadarW
RadarW
RadarW
RadarW
Adjust the white balance reference at 3200K.
Subject
Clear chart
(Color reproduction adjustment frame)
(Color reproduction adjustment frame)
Adjustment Page
F
Adjustment Address
2A to 2D
Note 1:
Perform “Color Reproduction Adjustment” before this
adjustment.
adjustment.
Note 2:
Check that the data of page: 0, address: 10 is “00”.
Note 3:
Check that the data of page: 6, address: 02 is “00”.
If not, select page: 6, address: 01, set data: 00, and press
the PAUSE (Write) button.
If not, select page: 6, address: 01, set data: 00, and press
the PAUSE (Write) button.
Switch setting:
1) POWER ......................................................... CAMERA mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
1) POWER ......................................................... CAMERA mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
Adjusting method:
Order Page Address Data
Procedure
1
Check that the picture frame
is “Color Reproduction
Adjustment Frame”. If not,
perform “6. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”.
is “Color Reproduction
Adjustment Frame”. If not,
perform “6. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”.
2
0
01
01
3
Wait for 2 seconds.
4
6
01
11
Press PAUSE (Write) button.
5
6
01
0B
Press PAUSE (Write) button.
(Note 4)
(Note 4)
6
6
02
Check the data changes to
“01”.
“01”.
Note 4:
The adjustment data will be automatically input to page:
F, address: 2A to 2D.
F, address: 2A to 2D.
Processing after completing adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE (Write) button.
2
0
01
00
6-25
DCR-HC28_ADJ
Adjusting method:
Order Page Address Data
Procedure
1
Check that the picture frame
is “Color Reproduction
Adjustment Frame”. If not,
perform “6. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”.
is “Color Reproduction
Adjustment Frame”. If not,
perform “6. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”.
2
Place the C14 filter on the
lens.
lens.
3
0
01
01
4
F
3E
Set the following data, and
press PAUSE (Write) button.
press PAUSE (Write) button.
2A: NTSC model
2A: PAL model
2A: PAL model
5
F
3F
Set the following data, and
press PAUSE (Write) button.
press PAUSE (Write) button.
78: NTSC model
38: PAL model
38: PAL model
6
F
40
Set the following data, and
press PAUSE (Write) button.
press PAUSE (Write) button.
5A: NTSC model
5C: PAL model
5C: PAL model
7
F
41
Set the following data, and
press PAUSE (Write) button.
press PAUSE (Write) button.
A0: NTSC model
20: PAL model
20: PAL model
8
6
01
83
Press PAUSE (Write) button.
9
6
01
81
Press PAUSE (Write) button.
(Note 5)
(Note 5)
10
6
02
Check the data changes to
“01”.
“01”.
Note 5:
The adjustment data will be automatically input to page:
F, address: 2E to 31.
F, address: 2E to 31.
Processing after completing adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE (Write) button.
2
0
01
00
3
Remove the C14 filter on the
lens.
lens.
11. Auto White Balance Adjustment
RadarW
RadarW
RadarW
RadarW
RadarW
Adjust to the proper auto white balance output data.
If it is not correct, auto white balance and color reproducibility
will be poor.
If it is not correct, auto white balance and color reproducibility
will be poor.
Subject
Clear chart
(Color reproduction adjustment
frame)
(Color reproduction adjustment
frame)
Filter
Filter C14 for color temperature
correction
correction
Adjustment Page
F
Adjustment Address
2E to 31, 3E to 41
Note 1:
Perform “Auto White Balance Standard Data Input” be-
fore this adjustment.
fore this adjustment.
Note 2:
Check that the data of page: 0, address: 10 is “00”.
Note 3:
Check that the data of page: 6, address: 02 is “00”.
If not, select page: 6, address: 01, set data: 00, and press
the PAUSE (Write) button.
If not, select page: 6, address: 01, set data: 00, and press
the PAUSE (Write) button.
Note 4:
NTSC model: DCR-HC28
PAL model: DCR-HC27E/HC28E
PAL model: DCR-HC27E/HC28E
Switch setting:
1) POWER ......................................................... CAMERA mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
1) POWER ......................................................... CAMERA mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
6-26
DCR-HC28_ADJ
12. Auto White Balance Check
RadarW
RadarW
RadarW
Subject
Clear chart
(Color reproduction adjustment frame)
(Color reproduction adjustment frame)
Filter
ND filter 1.0, 0.4 and 0.1
Measurement Point
Video terminal of
Displayed data of
A/V OUT jack
page: 1 (Note 3)
(75
Ω
terminated)
Measuring Instrument
Vectorscope
Adjusting remote
commander
commander
Specified Value
Fig. 6-1-15
InOut data:
(A) and (B)
8000 to 8BC0
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Note 2:
Perform “Auto White Balance Adjustment” before this
adjustment.
adjustment.
Note 3:
The right four digits of the page: 1 displayed data of the
adjusting remote commander.
adjusting remote commander.
1:XX:XX
Displayed data
Switch setting:
1) POWER ......................................................... CAMERA mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
1) POWER ......................................................... CAMERA mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
Checking method:
Order Page Address Data
Procedure
1
Check that the picture frame
is “Color Reproduction
Adjustment Frame”. If not,
perform “6. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”.
is “Color Reproduction
Adjustment Frame”. If not,
perform “6. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”.
2
Check that the lens is not
covered with either filter.
covered with either filter.
INDOOR check
3
6
01
0F
Press PAUSE (Write) button.
4
Check that the center of the
white luminance point within
the circle shown Fig. 6-1-15
(A)
white luminance point within
the circle shown Fig. 6-1-15
(A)
5
6
01
00
Press PAUSE (Write) button.
OUTDOOR check
6
6
01
3F
Press PAUSE (Write) button.
7
Check that the center of the
white luminance point within
the circle shown Fig. 6-1-15
(B)
white luminance point within
the circle shown Fig. 6-1-15
(B)
InOut data check
8
Place the ND filter 1.5 (1.0 +
0.4 + 0.1) on the lens.
0.4 + 0.1) on the lens.
9
6
01
00
Press PAUSE (Write) button.
10
0
03
06
11
1
Check that the displayed data
(Note 3) satisfied the InOut
data specified value.
(Note 3) satisfied the InOut
data specified value.
Fig. 6-1-15 (A)
R-Y
2 mm
B-Y
2 mm
Fig. 6-1-15 (B)
R-Y
B-Y
3 mm
6.5 mm
9 mm
3 mm
Processing after completing adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE (Write) button.
2
0
03
00
3
Remove the ND filter 1.5
(1.0 + 0.4 + 0.1) on the lens.
(1.0 + 0.4 + 0.1) on the lens.
Click on the first or last page to see other DCR-HC28 (serv.man3) service manuals if exist.