Sony DCR-DVD308 (serv.man3) Service Manual ▷ View online
6-22
DCR-DVD308_ADJ
9) After setting the picture frame, if the [End] button is clicked,
“7. Color Reproduction Adj.” is executed. The following mes-
sage is displayed, and then adjust the burst position of the
vectorscope.
sage is displayed, and then adjust the burst position of the
vectorscope.
10) If the [OK] button is clicked, the following message is dis-
played, and then adjust the luminance point of each color us-
ing the [Up]/[Down] button on the screen. After the adjustment
finished, click the [End] button.
ing the [Up]/[Down] button on the screen. After the adjustment
finished, click the [End] button.
11) After the adjustment, if the [End] button is clicked, “8. Color
Reproduction Check” is executed.
12) Upon successful completion of the “8. Color Reproduction
Check”, the following message is displayed. Then, set the pic-
ture frame in accordance with the message.
ture frame in accordance with the message.
13) If the [OK] button is clicked, “9. Picture Frame Setting (AWB
Adjustment Frame)” is executed. The following messages are
displayed in the order given below during the execution. Then,
change the chart in accordance with the messages.
displayed in the order given below during the execution. Then,
change the chart in accordance with the messages.
Fig. 6-1-14
NTSC model
PAL model
Burst position
R-Y
B-Y
R
G
B
M
G
C
Y
Y
E
Burst position
R-Y
B-Y
G
B
M
G
C
Y
Y
E
R
6-23
DCR-DVD308_ADJ
14) After the setting, if the [OK] button is clicked, the adjustment
items from “10. AWB Standard Data Input” to “13. AWB
Check” are executed. During the execution, the following
messages are displayed in the order given below. Place or re-
move the filters on the lens in accordance with the messages.
Check” are executed. During the execution, the following
messages are displayed in the order given below. Place or re-
move the filters on the lens in accordance with the messages.
15) Upon completion of “13. AWB Check”, “14. Release of Data
Setting during Camera Adj.” is executed
16) Upon successful completion of all items of the CAMERA
Adjustment 4, the following message is displayed. Click the
[OK] button.
[OK] button.
8.
CAMERA Adjustment 5
[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. Steady Shot Check
3. Release of Data Setting during Camera Adj.
sequence]
1. Data Setting during Camera Adj.
2. Steady Shot Check
3. Release of Data Setting during Camera Adj.
[Adjusting method]
1) Click the [Start] button of the CAMERA Adjustment 5.
2) The Automatic Adjustment Program executes “1. Data Setting
1) Click the [Start] button of the CAMERA Adjustment 5.
2) The Automatic Adjustment Program executes “1. Data Setting
during Camera Adj.”.
3) Upon successful completion of the “1. Data Setting during
Camera Adj.”, the following message is displayed.
With the camcoder in stationary state, click the [OK] button.
With the camcoder in stationary state, click the [OK] button.
4) If the [OK] button is clicked, “2. Steady Shot Check” is ex-
ecuted.
Upon successful completion of the “2. Steady Shot Check”,
the following message is displayed. Check that the steadyshot
function operates normally in accordance with the message.
Upon successful completion of the “2. Steady Shot Check”,
the following message is displayed. Check that the steadyshot
function operates normally in accordance with the message.
5) If the [OK] button is clicked, “3. Release of Data Setting dur-
ing Camera Adj.” is executed.
6) Upon successful completion of all items of the CAMERA
Adjustment 5, the following message is displayed. Click the
[OK] button.
[OK] button.
6-24
DCR-DVD308_ADJ
1-7.
AJUSTE DE SISTEMA DO LCD/EVF
1.
Function of Each Button on LCD/EVF System
Adjustment Screen
Adjustment Screen
Click the [LCD/EVF SYSTEM ADJUSTMENT] button on the Main
Menu screen, and the “LCD/EVF SYSTEM ADJUSTMENT”
screen in Fig. 6-1-15 will appear.
Menu screen, and the “LCD/EVF SYSTEM ADJUSTMENT”
screen in Fig. 6-1-15 will appear.
Fig. 6-1-15
3
2
1
Note:
The adjustment data cannot be read or written from the SeusEX.
Block
Page
Address
VCO Adj.
10
60
1050 (NTSC model),
1051 (PAL model)
1051 (PAL model)
Contrast Adj.
10
60
1058
V-COM Adj.
10
60
1052
Transmissive Mode White Balance Adj.
10
60
1056, 1057
Reflective Mode White Balance Adj.
10
60
107B, 107C
VCO Adj.
10
60
103F (NTSC model),
1040 (PAL model)
1040 (PAL model)
Contrast Adj.
10
60
1047
White Balance Adj.
10
60
1045, 1046
Touch Panel
Adjustment
Adjustment
Touch Panel Adj.
Adjusting Address
(Note)
Button Name
Adjustment
LCD
Adjustment
Adjustment
EVF
Adjustment
Adjustment
Table 6-1-5
1
[To Menu] button
The Main Menu screen comes back.
The Main Menu screen comes back.
2
[Start] button
Each adjustment “LCD Adjustment”, “EVF Adjustment” or
“Touch Panel Adjustment” starts.
Each adjustment “LCD Adjustment”, “EVF Adjustment” or
“Touch Panel Adjustment” starts.
3
[Release Data Setting] button
The data setting at the adjustment is cancelled.
During the data setting, the button color changes from “white”
to “red”. When the data setting is cancelled, the button color
returns to “white”.
(Use this button when an error occurred in the LCD/EVF ad-
justment. If the adjustment completed successfully, the data
setting is automatically cancelled and the button color returns
to “white”.)
The data setting at the adjustment is cancelled.
During the data setting, the button color changes from “white”
to “red”. When the data setting is cancelled, the button color
returns to “white”.
(Use this button when an error occurred in the LCD/EVF ad-
justment. If the adjustment completed successfully, the data
setting is automatically cancelled and the button color returns
to “white”.)
2.
Adjustment Items of LCD/EVF System Adjustment
The adjustment items of LCD/EVF system adjustment are as listed
in Table 6-1-5. The Automatic Adjustment Program executes the
adjustment items if the LCD/EVF Adjustment Start button is
clicked.
in Table 6-1-5. The Automatic Adjustment Program executes the
adjustment items if the LCD/EVF Adjustment Start button is
clicked.
6-25
DCR-DVD308_ADJ
4) If the [End] button is clicked, the following screen is displayed
during the execution of “4. Transmissive Mode White Balance
Adj.”. Check that the LCD screen is not colored. If colored,
using the [Up] / [Down] button on the screen, adjust so that the
LCD screen is not colored. After the adjustment, click the [End]
button in the screen.
Adj.”. Check that the LCD screen is not colored. If colored,
using the [Up] / [Down] button on the screen, adjust so that the
LCD screen is not colored. After the adjustment, click the [End]
button in the screen.
5) If the [End] button is clicked, “5. Reflective Mode White Bal-
ance Adj.” will be executed.
6) Upon successful completion of the “5. Reflective Mode White
Balance Adj.”, “6. Release of Data Setting during LCD/EVF
Adj.” will be executed.
Adj.” will be executed.
7) Upon successful completion of all item the LCD Adjustment,
the following message is displayed. Click the [OK] button.
3.
LCD Adjustment
[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during LCD/EVF Adj.
2. LCD Automatic Adj.
sequence]
1. Data Setting during LCD/EVF Adj.
2. LCD Automatic Adj.
(VCO Adj., Contrast Adj.)
3. V-COM Adj.
4. Transmissive Mode White Balance Adj.
5. Reflective Mode White Balance Adj.
6. Release of Data Setting during LCD/EVF Adj.
4. Transmissive Mode White Balance Adj.
5. Reflective Mode White Balance Adj.
6. Release of Data Setting during LCD/EVF Adj.
[Adjusting method]
1) Click the [Start] button of the LCD Adjustment.
2) The Automatic Adjustment Program executes the “1. Data
1) Click the [Start] button of the LCD Adjustment.
2) The Automatic Adjustment Program executes the “1. Data
Setting during LCD/EVF Adj.” and “2. LCD Automatic Adj.”.
3) After that, the following screen is displayed during the execu-
tion of “3. V-COM Adj.”. Using the [Up] / [Down] button on
the screen, adjust so that the brightness of portions A and B on
the LCD panel is equal. After the adjustment, click the [End]
button in the screen.
the screen, adjust so that the brightness of portions A and B on
the LCD panel is equal. After the adjustment, click the [End]
button in the screen.
Click on the first or last page to see other DCR-DVD308 (serv.man3) service manuals if exist.