Sony DCR-DVD305 (serv.man3) Service Manual ▷ View online
6-2
DCR-DVD305
Precaution on Replacing the VC-423 board
• Perform “Exif Model Data Check” mentioned below, and also the adjustment items necessary after VC Board re-
placement.
Exif Model Data Check
When you replace to the repairing board, the written data of repairing board also might be changed to original setting.
When the data has changed because of board replaceing etc, check the data setting (Exif Model Data) is right. If not,
rewrite to the right value.
When the data has changed because of board replaceing etc, check the data setting (Exif Model Data) is right. If not,
rewrite to the right value.
Exif Model Data
Writing Method:
1) Select page: 0, address: 01 and set data: 01.
2) Select page: A, address: B7 to BA, and set the Exif Model Data.
1) Select page: 0, address: 01 and set data: 01.
2) Select page: A, address: B7 to BA, and set the Exif Model Data.
Note:
To write in the non-volatile memory (EEPROM), press the PAUSE (Write) button each time to set the data.
3) Select page: 0, address: 01, and set data: 00.
Address
B7
B8
B9
BA
Page
A
A
A
A
Data
DCR-DVD205
32
30
35
00
DCR-DVD305
33
30
35
00
Address
B7
B8
B9
BA
Page
A
A
A
A
Data
DCR-DVD205E
32
30
35
45
DCR-DVD304E
33
30
34
45
DCR-DVD305E
33
30
35
45
DCR-DVD705E
37
30
35
45
DCR-DVD705
37
30
35
00
DCR-DVD755
37
35
35
00
DCR-DVD755E
37
35
35
45
6-3
DCR-DVD305
Table 6-1-1 (1)
1-1. Adjusting items when replacing main parts and boards
•
Adjusting items when replacing main parts
When replacing main parts, adjust the items indicated by z in the following table.
Note 1:
The Automatic Adjustment Program does not support
Note 2:
DCR-DVD304E/DVD305/DVD305E/DVD755/DVD755E only
Lens device
Drive block
LCD block LCD9001 (LCD panel)
EVF block LCD9002 (LCD panel)
PS19100 block (Control switch block (zoom lever))
Accessory microphone
CD-601 board IC6101 (CCD imager )
LB-120 board D302 (EVF backlight)
MA-443 board SE6301, 6302 (YAW, PITCH sensor)
PD-268 board D6503 - 6505 (LCD backlight)
VC-423 board IC1401, X1401 (A/D converter, Timing generator)
VC-423 board IC2803 (Video/Audio DSP)
VC-423 board IC2901 (Video, Audio I/O)
VC-423 board IC3301 (MIC AMP)
VC-423 board IC3401 (Aspect ratio converter)
VC-423 board IC3601 (Sub MIC AMP)
VC-423 board IC4001 (RF process)
VC-423 board IC4101 (DVD DSP)
VC-423 board IC4302 (DVD mecha drive)
VC-423 board IC5101 (LCD/EVF driver)
Initialization of 9, A, B, D, 13,
15, 17, 1A, 1B, page data
Initialization of E, F, 14, 19, 1E, 1F page data
Initialization of C, 1C page data
15, 17, 1A, 1B, page data
Initialization of E, F, 14, 19, 1E, 1F page data
Initialization of C, 1C page data
(Note 1)
33MHz/27MHz origin oscillation check
z
IC3401 LINE OUT Y gain adj.
IC3401 LINE OUT chroma gain adj.
S VIDEO OUT Y level adj.
S VIDEO OUT chroma level adj.
IC3401adj.
HALL adj.
MR adj.
IC3401 LINE OUT chroma gain adj.
S VIDEO OUT Y level adj.
S VIDEO OUT chroma level adj.
IC3401adj.
HALL adj.
MR adj.
CAMERA
adjustment 2
adjustment 2
Flange back and zoom lever center adj.
z
z
z
CAMERA
adjustment 3
adjustment 3
Flange back check
z
z
F No. & ND light qualiy
standard data input
MAX GAIN adj.
Mechanical shutter adj
Color reproduction adj.
AWB standard data input
LV standard data input
Auto white balance adj.
standard data input
MAX GAIN adj.
Mechanical shutter adj
Color reproduction adj.
AWB standard data input
LV standard data input
Auto white balance adj.
CAMERA
adjustment 5
adjustment 5
Steady shot check
z
LCD automatic adj.
V-COM adj. (LCD)
V-COM adj. (LCD)
Transmissive moed
white balance adj. (LCD)
Reflective mode
white balance adj. (LCD)
EVF automatic adj.
White balance adj. (EVF)
white balance adj. (LCD)
Reflective mode
white balance adj. (LCD)
EVF automatic adj.
White balance adj. (EVF)
AUDIO
ajustment
ajustment
Accessory 4ch microphone sensitivity adj.
(Note 2)
(Note 2)
z
z
z
POWER adj.
z
z
z
z
DVD-R adj.
z
z
z
z
DVD-RW adj.
z
z
z
z
DVD+RW adj.
z
z
z
z
Replaceed parts
Parts replacement
Block replacement
z
z
z
z
z
z
z
z
z
z
z
z
z
z
AUDIT
CAMERA
adjustment 4
adjustment 4
z
LCD
adjustment
adjustment
EVF
adjustment
adjustment
Touch panel
adjustment
adjustment
Adjustment
CAMERA
adjustment 1
adjustment 1
VIDEO
adjustment
adjustment
Adjusting item
(Note 1)
Touch panel adj.
z
6-4
DCR-DVD305
• Adjusting items when replacing a board or EEPROM
When replacing a board or EEPROM, adjust the items indicated by z in the following table.
When replacing a board or EEPROM, adjust the items indicated by z in the following table.
Table 6-1-1 (2)
Note 3: IC3101 (Flash memory) on
the VC-423 board and
IC4202 (Flash memory) on
the VC-423 board cannot be
replaced.
IC4202 (Flash memory) on
the VC-423 board cannot be
replaced.
Note 4: When replacing the VC-423
board, perform “Exif Model
Data Check” after replace-
ment.
Data Check” after replace-
ment.
CD-601 board (COMPLETE)
LB-120 board (COMPLETE)
MA-443 board (COMPLETE)
PD-268 board (COMPLETE)
VC-423 board (COMPLETE) (Note 4)
VC-423 board IC2602 (EEPR
OM)
VC-423 board IC3003 (EEPR
OM)
Initialization of 9, A, B, D, 13,
15, 17, 1A, 1B, page data
15, 17, 1A, 1B, page data
z
z
Initialization of E, F, 14, 19, 1E, 1F page data
z
z
Initialization of C, 1C page data
z
z
(Note 1)
33MHz/27MHz origin oscillation check
z
z
IC3401 LINE OUT Y gain adj.
IC3401 LINE OUT chroma gain adj.
S VIDEO OUT Y level adj.
S VIDEO OUT chroma level adj.
IC3401adj.
HALL adj.
MR adj.
IC3401 LINE OUT chroma gain adj.
S VIDEO OUT Y level adj.
S VIDEO OUT chroma level adj.
IC3401adj.
HALL adj.
MR adj.
CAMERA
adjustment 2
adjustment 2
Flange back and zoom lever center adj.
z
z
z
CAMERA
adjustment 3
adjustment 3
Flange back check
z
z
z
F No. & ND light qualiy
standard data input
MAX GAIN adj.
Mechanical shutter adj
Color reproduction adj.
AWB standard data input
LV standard data input
Auto white balance adj.
standard data input
MAX GAIN adj.
Mechanical shutter adj
Color reproduction adj.
AWB standard data input
LV standard data input
Auto white balance adj.
CAMERA
adjustment 5
adjustment 5
Steady shot check
z
z
LCD automatic adj.
V-COM adj. (LCD)
V-COM adj. (LCD)
Transmissive moed
white balance adj. (LCD)
Reflective mode
white balance adj. (LCD)
EVF automatic adj.
White balance adj. (EVF)
white balance adj. (LCD)
Reflective mode
white balance adj. (LCD)
EVF automatic adj.
White balance adj. (EVF)
AUDIO
ajustment
ajustment
Accessory 4ch microphone sensitivity adj.
(Note 2)
(Note 2)
z
POWER adj.
z
DVD-R adj.
z
DVD-RW adj.
z
DVD+RW adj.
z
z
z
z
z
z
EEPROM
replacement
Board
replacement
(Note 1)
z
z
z
z
z
CAMERA
adjustment 4
adjustment 4
z
Adjusting item
Adjustment
z
VIDEO
adjustment
adjustment
AUDIT
z
z
z
CAMERA
adjustment 1
adjustment 1
Touch panel adj.
LCD
adjustment
adjustment
EVF
adjustment
adjustment
Touch panel
adjustment
adjustment
6-5
DCR-DVD305
1-2. List of service tools
•
Oscilloscope
•
Color monitor
•
Vectorscope
•
Frequency counter
•
Audio level meter
•
Audio generator
•
Audio attenuator
•
Audio distortion meter
•
Amplifier built-in speaker for PC
•
Adjustment sound source file
Fig. 6-1-1 (1)
Personal computer
(Note 1, 2)
(Note 1, 2)
J-1
HASP key and application
for adjustment (SeusCam)
for adjustment (SeusCam)
Contact our service headquater of each area
how to get the application for adjustment
(SeusCam) and HASP key.
how to get the application for adjustment
(SeusCam) and HASP key.
J-2
USB cable
1-829-579-61
1-829-579-61
J-3
J-4
Adjustment remote
commander
(RM-95)
J-6082-053-B
commander
(RM-95)
J-6082-053-B
J-13
J-9
J-7
Pattern box PTB-450
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
J-10
Color bar chart
For PTB-450:
J-6020-250-A
J-6020-250-A
For PTB-1450:
J-6082-559-A
J-6082-559-A
J-11
Clear chart
For PTB-450:
J-6080-621-A
J-6080-621-A
For PTB-1450:
J-6082-560-A
J-6082-560-A
J-12
Minipattern box
J-6082-353-B
J-6082-353-B
Siemens star chart
J-6080-875-A
J-6080-875-A
Filter for color
temperature correction
(C14)
J-6080-058-A
temperature correction
(C14)
J-6080-058-A
J-14
ND filter 1.0
J-6080-808-A
J-6080-808-A
ND filter 0.4
J-6080-806-A
J-6080-806-A
ND filter 0.1
J-6080-807-A
J-6080-807-A
J-8
Flange back
adjustment jig
J-6082-563-A
adjustment jig
J-6082-563-A
J-15
Camera table
J-6082-384-A
J-6082-384-A
J-6
LANC cable
J-6082-442-A
J-6082-442-A
J-5
Adjustment remote
commander
(NEW LANC JIG)
J-6082-565-A
commander
(NEW LANC JIG)
J-6082-565-A
Note 1:
Personal computer
OS:
OS:
Windows 98/98SE/Me/2000/XP Home/XP Pro (Camera Section)
Windows 2000/XP Home/XP Pro (Drive Section)
Windows 2000/XP Home/XP Pro (Drive Section)
RAM: 256MB or more recommended
USB:
USB:
2.0 recommended (also compatible with 1.1)
Three connectors are required.
Three connectors are required.
Note 2:
The following programs and driver must already be installed in the personal computer. (Contact our service headquater of each
area how to get the programs and driver)
area how to get the programs and driver)
•
SeusCam
•
Optical power meter driver
•
AUDIT
Click on the first or last page to see other DCR-DVD305 (serv.man3) service manuals if exist.