Sony DCR-DVD200 / DCR-DVD200E / DCR-DVD300 (serv.man2) Service Manual ▷ View online
2-22
DCR-DVD200/DVD200E/DVD300
2-32.LENS DEVICE (LSV-751A)
8
FP-606 flexible board
(24P)
q;
Optical filter block
qa
Seal rubber (W)
qd
CCD block assembly
3
Outer connector (hot shoe),
Lens frame (750), etc
4
CD heat sink (750)
2
Screw
(M1.7
×
2.5),
lock ace, p2
5
Two tapping screws
(M1.7
×
5)
qf
CD-429 board
1
Two tapping screws
(M1.7
×
3.5)
9
CD radiation sheet
CD radiation
sheet
sheet
qs
Remove the soldering
qh
Lens device
(LSV-751A)
6
Two dowels
Caution
qg
Lens (650) sheet
7
Harness (CV-068) (2P)
2-23
DCR-DVD200/DVD200E/DVD300
2-33.VC-310 BOARD
VC-310
VC-310
MD-097
5
Control switch block
(PS-CX5500) (14P)
6
Three screws
(M1.7
×
2.5),
lock ace, p2
9
VC-310 board
8
Flexible retainer
cushion
Flexible retainer
cushion
cushion
3
Two screws
(M1.7
×
2.5),
lock ace, p2
4
FP-611 flexible board,
JK frame
2
FP-611 flexible board (8P)
1
FP-605 flexible board (22P)
7
Board to board connector
(100P)
q;
Heat sink,
sheet radiation (A),
sheet radiation (B)
sheet radiation (B)
Caution
Attach the flexible retainer
cushion as shown in the
illustration.
cushion as shown in the
illustration.
2-24
DCR-DVD200/DVD200E/DVD300
[SERVICE POSITION TO CHECK THE DVD DRIVE SECTION]
Connection to Check the VTR Section
Connection to Check the VTR Section
To check the DVD drive section, set the DVD drive to forced PLAY mode.
Operate the DVD drive using the adjustment remote commander (with the HOLD switch set in the OFF position).
Operate the DVD drive using the adjustment remote commander (with the HOLD switch set in the OFF position).
Setting the forced PLAY mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: D, address: 10, set data: 02, and press the
PAUSE button of the adjustment remote commander.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: D, address: 10, set data: 02, and press the
PAUSE button of the adjustment remote commander.
Exiting the forced PLAY mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: D, address: 10, set data: 00, and press the
PAUSE button of the adjustment remote commander.
4) Select page: 0, address: 01, and set data: 00.
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: D, address: 10, set data: 00, and press the
PAUSE button of the adjustment remote commander.
4) Select page: 0, address: 01, and set data: 00.
1
2-2. F PANEL SECTION .....................................
2
2-4. CABINET (R) SECTION ..............................
3
2-26. BATTERY PANEL SECTION........................
4
2-27. EVF SECTION..............................................
5
2-31. LENS SECTION...........................................
6
2-33. VC-310 BOARD............................................
(page 2-3)
(page 2-4)
(page 2-16)
(page 2-17)
(page 2-21)
(page 2-23)
PROCEDURE OF REMOVING THE VC-310 BOARD.
(SERVICE POSITION) TO CHECK THE DVD DRIVE SECTION)
(SERVICE POSITION) TO CHECK THE DVD DRIVE SECTION)
CN4901
CN4001
CN1008
CN1009
CN4902
VC-310
MD-097
VC-310 board
LANC jack
AUDIO/
VIDEO jack
VIDEO jack
Monitor TV
DC-IN jack
Extension cable (100P)
(J-6082-352-A)
(J-6082-352-A)
AC power
adaptor
adaptor
AC IN
CPC-8 jig
(J-6082-388-A)
(J-6082-388-A)
Adjustment remote
commander (RM-95)
commander (RM-95)
Battery panel section
2-25
DCR-DVD200/DVD200E/DVD300
2-34.MD-097 BLOCK ASSEMBLY
MD-097
MD-097
MD-097
Optical pickup
4
Tape (0716)
2
Zoom blind
8
Three tapping screws
(M1.7
×
5)
7
Screw
(M1.7
×
2.5),
lock ace, p2
3
NS knob (650),
NS base (650)
5
FP-608
flexible board
(10P)
(10P)
6
FP-609 flexible board
(8P)
9
MD-097 block assembly
Caution
Caution
Precautions during handling
Refer to level 3
Attach the Tape (0716)
as shown in the
illustration.
as shown in the
illustration.
Disassembling procedure of
MD-097 block assembly.
MD-097 block assembly.
Tape (0716)
FP-608 flexible board
1
Screw (M1.7
×
4),
lock ace, p2 (black)
Be sure to place the DVD drive with
its optical pickup facing upward.
Hold the frame.
Do not touch the optical pickup surface.
its optical pickup facing upward.
Hold the frame.
Do not touch the optical pickup surface.
Use the adjustable wrist strap (J-2501-162-A) as the preventive
measure for static electricity when the removing and installing
the drum assemb
measure for static electricity when the removing and installing
the drum assemb
ly because the drum assembly of this
mechanism beck is easily affected by the static electricity.
(J-2501-162-A)
Caution
Click on the first or last page to see other DCR-DVD200 / DCR-DVD200E / DCR-DVD300 (serv.man2) service manuals if exist.