Sony CCD-TRV15 / CCD-TRV15E / CCD-TRV15EP / CCD-TRV15PK / CCD-TRV215 / CCD-TRV25 / CCD-TRV25PK / CCD-TRV35 / CCD-TRV35E / CCD-TRV615 / CCD-TRV65 / CCD-TRV65PK / CCD-TRV815 / CCD-TRV85 / CCD-TRV93 Service Manual ▷ View online
5-2
1-1-2. Preparations
Note 1:
For details of how remove the cabinet and boards, refer to
“2. DISASSEMBLY”.
“2. DISASSEMBLY”.
Note 2:
When performing only the adjustments, the lens block and
boards need not be disassembled.
boards need not be disassembled.
1) Connect the equipment for adjustments according to Fig. 5-1-3,
4.
2) By setting the “Forced Camera Power ON mode”, the camera
power can be turned ON even if the front panel block (MA-311/
312/331 board, power switch, microphone unit) has been
removed. When removing the front panel block disconnect the
following connector.
312/331 board, power switch, microphone unit) has been
removed. When removing the front panel block disconnect the
following connector.
1. VC-195 board CN903 (23P 0.5mm)
3) The intelligent accessory shoe (Intelligent accessory shoe model)
or video light (Video light model) need not be assembled. If
removing it. disconnect the following connector.
removing it. disconnect the following connector.
1. VC-195 board CN909 (10P, 0.5mm)
Note 3:
As removing the cabinet (R) (removing the VC-195 board
CN911) means removing the lithium 3V power supply
(CF-50/51 board) , data such as date, time, user-set menus
will be lost. After completing adjustments, reset these data.
If the cabinet (R) has been removed, the self-diagnosis
data, data on history of use (total drum rotation time etc. )
will be lost. Before removing, note down the self-diagnosis
data and data on the history use. (Refer to the “Service
Mode” of “VIDEO SECTION ADJUSTMENT” for the
data on the history use.)
CN911) means removing the lithium 3V power supply
(CF-50/51 board) , data such as date, time, user-set menus
will be lost. After completing adjustments, reset these data.
If the cabinet (R) has been removed, the self-diagnosis
data, data on history of use (total drum rotation time etc. )
will be lost. Before removing, note down the self-diagnosis
data and data on the history use. (Refer to the “Service
Mode” of “VIDEO SECTION ADJUSTMENT” for the
data on the history use.)
Note 4:
Setting the “Forced Camera Power ON” Mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the
PAUSE button of the adjusting remote commander.
The above procedure will enable the camera power to
be turned on with the front panel block removed. After
completing adjustments, be sure to exit the “Forced
Camera Power ON Mode”.
The above procedure will enable the camera power to
be turned on with the front panel block removed. After
completing adjustments, be sure to exit the “Forced
Camera Power ON Mode”.
Note 5:
Exiting the “Forced Camera Power ON” Mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the
PAUSE button of the adjusting remote commander.
3) Select page: 0, address: 01, and set data: 00.
Fig. 5-1-2.
Pattern box
1.5m
Front of lens
5-3
2.5 INCH LCD MODEL
Fig. 5-1-3.
Color monitor
Vector scope
Terminated at 75
Ω
Lens block
CD-197 board
CN401
CN401
Extension cable(16P)
(J-6082-357-A)
(J-6082-357-A)
Need not connected
VIDEO terminal
CN909
CN551
CN902
CN903
CN901
CN001
CN905
CN906 CN905
CN914
CN910
CN911
CN912
MA-311/331 board
CN303
CN303
Extension cable(48P)
(J-6082-188-A)
(J-6082-188-A)
CF-50
board
CN001
board
CN001
PD-92 board
CN580
CN580
PD-92 board
CN5701
CN5501
CN5001
CN5805
CN5802
CN5803
CN5804
Multi CPC jig
(J-6082-311-A)
(J-6082-311-A)
Must be connected when
performing the LCD system
adjustments.
performing the LCD system
adjustments.
CPC-7 jig
(J-6082-382-A)
(J-6082-382-A)
Must be connected when
performing the VIDEO system
adjustments.
performing the VIDEO system
adjustments.
CN935
CN932
CN934
CN801
CN931
CN933
DD-105
board
board
LANC
jack
jack
Adjusting
remote
commander
remote
commander
Regulaterd power supply
(8.4
(8.4
±
0.1 Vdc)
Battery
terminal
(Note 2)
terminal
(Note 2)
VC-195
board
board
CN501
Note 1 :
2.5” LCD model : CCD-TRV15/TRV15E/TRV15EP/
TRV15PK/TRV25/TRV25PK/TRV35/TRV35E/
TRV65/TRV65PK/TRV215/TRV615
TRV65/TRV65PK/TRV215/TRV615
Note 2 :
Connect the adjusting remote commander to the LANC
jack, and set the HOLD switch to the “ADJ” side, or use
the AC power adaptor.
jack, and set the HOLD switch to the “ADJ” side, or use
the AC power adaptor.
5-4
3/3.5 INCH LCD MODEL
Fig. 5-1-4.
Color monitor
Vector scope
Terminated at 75
Ω
Lens block
CD-198 board
CN401
CN401
Extension cable(16P)
(J-6082-357-A)
(J-6082-357-A)
Need not connected
VIDEO terminal
CN909
CN551
CN902
CN903
CN901
CN001
CN905
CN906 CN905
CN914
CN910
CN911
CN912
MA-312 board
CN303
CN303
Extension cable(48P)
(J-6082-188-A)
(J-6082-188-A)
CF-51
board
CN001
board
CN001
PD-93 board
CN580
CN580
PD-93 board
CN4701
CN4501
CN4601
CN4805
CN4802
CN4803
CN4804
Multi CPC jig
(J-6082-311-A)
(J-6082-311-A)
Must be connected when
performing the LCD system
adjustments.
performing the LCD system
adjustments.
CPC-7 jig
(J-6082-382-A)
(J-6082-382-A)
Must be connected when
performing the VIDEO system
or color EVF system
adjustments.
performing the VIDEO system
or color EVF system
adjustments.
CN935
CN932
CN934
CN801
CN931
CN933
DD-105
board
board
LANC
jack
jack
Adjusting
remote
commander
remote
commander
Regulaterd power supply
(8.4
(8.4
±
0.1 Vdc)
Battery
terminal
(Note 2)
terminal
(Note 2)
CN501
VC-195
board
board
Note 1 :
3” LCD model : CCD-TRV93
3.5”LCD MODEL ; CCD-TRV85/TRV815
3.5”LCD MODEL ; CCD-TRV85/TRV815
Note 2 :
Connect the adjusting remote commander to the LANC
jack, and set the HOLD switch to the “ADJ” side, or use
the AC power adaptor.
jack, and set the HOLD switch to the “ADJ” side, or use
the AC power adaptor.
5-5
1-1-3.Precaution
1. Setting the Switch
1. Setting the Switch
Unless otherwise specified, set the switches as follows and perform
adjustments without loading cassette.
1. POWER switch (MA-311/312/331 board) ............. CAMERA
2. NIGHT SHOT switch (Lens Block) ................................ OFF
adjustments without loading cassette.
1. POWER switch (MA-311/312/331 board) ............. CAMERA
2. NIGHT SHOT switch (Lens Block) ................................ OFF
(Night shot model)
3. VIDEO LIGHT switch (MA-312 board) ........................ OFF
(Video light model)
4. DEMO MODE (Menu display) ....................................... OFF
5. DIGITAL ZOOM (Menu display) ................................... OFF
6. STEADY SHOT (Menu display) .................................... OFF
5. DIGITAL ZOOM (Menu display) ................................... OFF
6. STEADY SHOT (Menu display) .................................... OFF
7. DISPLAY (Menu display) ................................. V-OUT/LCD
8. FOCUS switch (MF-8500/MR-8500)
8. FOCUS switch (MF-8500/MR-8500)
(Manual Focus model) .......................................... MANUAL
9. PROGRAM AE (CF-50/51 board) .................................. Auto
10. BACK LIGHT (CF-50/51 board) .................................... OFF
11. PICTURE EFECT (CF-50/51 board) .............................. OFF
12. 16 : 9 WIDE (MENU display) ........................................ OFF
10. BACK LIGHT (CF-50/51 board) .................................... OFF
11. PICTURE EFECT (CF-50/51 board) .............................. OFF
12. 16 : 9 WIDE (MENU display) ........................................ OFF
2. Adjusting Procedure
Adjust in the given order.
Fig. 5-1-5.
3. Subject
1) Color bar chart (Standard picture frame)
Adjust the picture frame as shown in Fig. 5-1-5. if adjustments
are performed using the color bar chart.
(Standard picture frame)
are performed using the color bar chart.
(Standard picture frame)
2) White pattern (Standard picture frame)
Remove the color bar chart from the pattern box, and insert a
clear chart in its place. (Do not perform zoom operations during
this time.)
clear chart in its place. (Do not perform zoom operations during
this time.)
3) Chart for flange back adjustment
Combine a white A0 size (1189 mm x 841 mm) paper to a black
one, and make the chart shown in Fig. 5-1-6.
one, and make the chart shown in Fig. 5-1-6.
Fig. 5-1-6.
Note :
Use the non-reflecting and non-glazing vellum paper
whose size is more than A0, and make the boundary
between white and black to be smoothly flat.
whose size is more than A0, and make the boundary
between white and black to be smoothly flat.
Color bar chart standard picture trame
H
A
B
A=B
B
A
0
±
0.1 msec
V
Enlargement
Difference in level
A
B
Electronic beam
scanning frame
scanning frame
CRT picture frame
Fig. b. (TV monitor picture)
Yellow
Cyan
Green
White
Magenta
Red
Blue
Yellow
Cyan
Green
White
Magenta
Red
Blue
Fig. a. (Video output terminal
output wavefom)
output wavefom)
Adjust the camera zoom and direction to obtain the output wavefom
shown in Fig. a and the TV monitor display shown in Fig. b.
shown in Fig. a and the TV monitor display shown in Fig. b.
841 mm
1189 mm
White
Black
Click on the first or last page to see other CCD-TRV15 / CCD-TRV15E / CCD-TRV15EP / CCD-TRV15PK / CCD-TRV215 / CCD-TRV25 / CCD-TRV25PK / CCD-TRV35 / CCD-TRV35E / CCD-TRV615 / CCD-TRV65 / CCD-TRV65PK / CCD-TRV815 / CCD-TRV85 / CCD-TRV93 service manuals if exist.