Sony CCD-TRV118 / CCD-TRV218E / CCD-TRV318 / CCD-TRV418 / CCD-TRV418E (serv.man2) Service Manual ▷ View online
CCD-TRV118/TRV218E/TRV318/TRV418/TRV418E
6-7
H
A=B
C=D
A B
B
C
D
A
Enlargement
V
Electronic beam scanning frame
CRT picture frame
B
A
Difference in level
Y
ello
w
Cy
an
Green
White
Magenta
Red
Blue
Ye
llo
w
Cy
an
Green
White
Magenta
Red
Blue
Color bar chart (Color reproduction adjustment frame)
Fig. a
(VIDEO terminal of A/V jack
output waveform)
(VIDEO terminal of A/V jack
output waveform)
Fig. b (monitor TV picture)
Adjust the camera zoom and direction to
obtain the output waveform shown in Fig. a and
the monitor TV display shown in Fig. b.
obtain the output waveform shown in Fig. a and
the monitor TV display shown in Fig. b.
1-1-3. Precaution
1.
1.
Setting the Switch
Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette.
1.
POWER switch (SS-3000 block) .......................... CAMERA
2.
FOCUS (CF-3000 block) ..................................... MANUAL
3.
BACK LIGHT (CF-3000 block) .................................... OFF
4.
PROGRAM AE (MENU setting) ................................... OFF
5.
NIGHT SHOT switch (Lens block) ............................... OFF
6.
EXPOSURE (CF-3000 block) .................................... AUTO
7.
P EFFECT (MENU setting) ........................................... OFF
8.
D ZOOM (MENU setting) ............................................. OFF
9.
DEMO MODE (MENU setting) .................................... OFF
10. 16 : 9 WIDE (MENU setting) ........................................ OFF
2.
Order of Adjustments
Basically carry out adjustments in the order given.
Fig. 6-1-5
3. Subjects
1)
Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 6-1-5. (Color reproduction
adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 6-1-5. (Color reproduction
adjustment frame)
2)
Clear chart (Color reproduction adjustment frame)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during
this time)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during
this time)
3) Chart for flange back adjustment
Join together a piece of white A0 size paper (1189mm
× 841
mm) and a piece of black paper to make the chart shown in
Fig. 6-1-6.
Fig. 6-1-6.
Note:
Use a non-reflecting and non-glazing vellum paper. The
size must be A0 or larger and the joint between the white
and black paper must not have any undulations.
size must be A0 or larger and the joint between the white
and black paper must not have any undulations.
Fig. 6-1-6
Black
White
841 mm
1189 mm
CCD-TRV118/TRV218E/TRV318/TRV418/TRV418E
6-8
COVER
COVER
1-2.
INITIALIZATION OF D, E, F, 7 PAGE DATA
1. Initializing the D, E, F, 7 Page Data
Note 1:
Note 1:
If “Initialization of Pages D, E, F, 7” is executed, all data
on pages D, E, F, 7 are initialized. (Only an individual
page cannot be initialized)
on pages D, E, F, 7 are initialized. (Only an individual
page cannot be initialized)
Note 2:
If the D, E, F, 7 page data has been initialized, “Modifi-
cation of D, E, F, 7 Page Data” and all adjustments need
to be performed again.
cation of D, E, F, 7 Page Data” and all adjustments need
to be performed again.
Note 3:
NTSC model: CCD-TRV118/TRV318/TRV418
PAL model: CCD-TRV218E/TRV418E
PAL model: CCD-TRV218E/TRV418E
Adjusting Page
D
Adjusting Address
10 to 87
Adjusting Page
E
Adjusting Address
00 to FF
Adjusting Page
F
Adjusting Address
10 to FF
Adjusting Page
7
Adjusting Address
00 to 63
Initializing method:
Order Page Address Data
Procedure
1
0
01
01
2
6
00
Set the following data.
55: NTSC model
51: PAL model
55: NTSC model
51: PAL model
3
6
01
Set the following data, and
press PAUSE button.
55: NTSC model
51: PAL model
press PAUSE button.
55: NTSC model
51: PAL model
4
6
02
Check the data changes to
“01”.
“01”.
5
2
00
29
6
2
01
29
Press PAUSE button.
7
Perform “Modification of D,
E, F, 7 Page Data”
E, F, 7 Page Data”
2. Modification of D, E, F, 7 Page Data
If the D, E, F, 7 page data has been initialized, change the data of
the “Fixed data-2” address shown in the following table by manual
input.
the “Fixed data-2” address shown in the following table by manual
input.
Modifying method:
1) Before changing the data, select page: 0, address: 01, and set
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
the data built in the same model.
Note:
If copy the data built in the different model, the
camcorder may not operate.
camcorder may not operate.
3) When changing the data, press the PAUSE button of the ad-
justment remote commander each time when setting new data
to write the data in the non-volatile memory.
to write the data in the non-volatile memory.
4) Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
Processing after Completing Modification of D, E, F, 7 Page
data
data
Order Page Address Data
Procedure
1
2
00
29
2
2
01
29
Press PAUSE button.
3
0
01
00
Note:
If the following symptoms occur after completing of the
“Modification of D, E, F, 7 page data”, check that the data
of the “Fixed data-2” addresses of D, E, F, 7 page are same
as those of the same model of the same destination.
1) The power is shut off so that unit cannot operate.
“Modification of D, E, F, 7 page data”, check that the data
of the “Fixed data-2” addresses of D, E, F, 7 page are same
as those of the same model of the same destination.
1) The power is shut off so that unit cannot operate.
CCD-TRV118/TRV218E/TRV318/TRV418/TRV418E
6-9
3. D Page Table
Note 1:
Note 1:
Fixed data-1: Initialized data. (Refer to “1. Initializing
the D, E, F, 7 Page Data”)
the D, E, F, 7 Page Data”)
Note 2:
Fixed data-2: Modified data. (Refer to “2. Modification
of D, E, F, 7 Page Data”)
of D, E, F, 7 Page Data”)
Address
Initial value
Remark
NTSC PAL
10
00
00
Test mode
11, 12
Fixed data-1 (Initialized data)
13
Fixed data-2
14 to 19
Fixed data-1 (Initialized data)
1A
Fixed data-2
1B to 21
Fixed data-1 (Initialized data)
22
23
Fixed data-2
24 to 26
Fixed data-1 (Initialized data)
27
Fixed data-2
28 to 33
Fixed data-1 (Initialized data)
34
35
Fixed data-2
36, 37
Fixed data-1 (Initialized data)
38
39
Fixed data-2
3A to 40
Fixed data-1 (Initialized data)
41
Fixed data-2
42 to 44
Fixed data-1 (Initialized data)
45
46
47
Fixed data-2
48
49 to 4C
Fixed data-1 (Initialized data)
4D
Fixed data-2
4E, 4F
Fixed data-1 (Initialized data)
50
Fixed data-2
51 to 5A
Fixed data-1 (Initialized data)
5B
Fixed data-2
5C to 72
Fixed data-1 (Initialized data)
73
Fixed data-2
74 to 7B
Fixed data-1 (Initialized data)
7C
Fixed data-2
7D to 84
Fixed data-1 (Initialized data)
85
Fixed data-2
86, 87
Fixed data-1 (Initialized data)
4. E Page Table
Note 1:
Note 1:
Fixed data-1: Initialized data. (Refer to “1. Initializing
the D, E, F, 7 Page Data”)
the D, E, F, 7 Page Data”)
Note 2:
Fixed data-2: Modified data. (Refer to “2. Modification
of D, E, F, 7 Page Data”)
of D, E, F, 7 Page Data”)
Address
Initial value
Remark
NTSC PAL
00 to 09
Fixed data-1 (Initialized data)
0A
Fixed data-2
0B
Fixed data-1 (Initialized data)
0C
0D
Fixed data-2
0E
Fixed data-1 (Initialized data)
0F
Fixed data-2
10 to 15
Fixed data-1 (Initialized data)
16
Fixed data-2
17
Fixed data-1 (Initialized data)
18
Fixed data-2
19 to 28
Fixed data-1 (Initialized data)
29
2A
Fixed data-2
2B
Fixed data-1 (Initialized data)
2C
Fixed data-2
2D
Fixed data-1 (Initialized data)
2E
2F
30
31
Fixed data-2
32
33
34
35 to 51
Fixed data-1 (Initialized data)
52
Fixed data-2
53 to 58
Fixed data-1 (Initialized data)
59
FF
FF
Optical axis adj.
5A to FF
Fixed data-1 (Initialized data)
CCD-TRV118/TRV218E/TRV318/TRV418/TRV418E
6-10
5. F Page Table
Note 1:
Note 1:
Fixed data-1: Initialized data. (Refer to “1. Initializing
the D, E, F, 7 Page Data”)
the D, E, F, 7 Page Data”)
Note 2:
Fixed data-2: Modified data. (Refer to “2. Modification
of D, E, F, 7 Page Data”)
of D, E, F, 7 Page Data”)
Address
Initial value
Remark
NTSC PAL
10
00
00
Emergency memory
11
00
00
12
00
00
13
00
00
14
00
00
15
00
00
16
00
00
17
00
00
18
00
00
19
00
00
1A
00
00
1B
00
00
1C to 1F
Fixed data-1 (Initialized data)
20
00
00
Test mode
21 to 23
Fixed data-1 (Initialized data)
24
Fixed data-2
25 to 27
Fixed data-1 (Initialized data)
28
Fixed data-2
29
Fixed data-1 (Initialized data)
2A
Fixed data-2
2B, 2C
Fixed data-1 (Initialized data)
2D
Fixed data-2
2E, 2F
Fixed data-1 (Initialized data)
30
52
68
HALL adj.
31
89
80
32
88
8D
33
Fixed data-2
34
80
80
AWB & LV standard data input
35
7A
7A
36
2B
2B
37
80
80
38
65
65
39
80
80
3A
8D
8D
Auto white balance adj.
3B
87
87
3C to 3E
Fixed data-1 (Initialized data)
3F
33
33
Color reproduction adj.
40
Fixed data-1 (Initialized data)
41
34
34
Color reproduction adj.
42 to 44
Fixed data-1 (Initialized data)
45
8C
8C
28 MHz origin osillation adj.
46
28
28
Flange back adj.
47
EC
EC
48
35
35
Address
Initial value
Remark
NTSC PAL
49
8F
8F
Flange back adj.
4A
13
13
4B
B8
B8
4C
2B
2B
4D
00
00
4E
19
19
4F
00
00
50
32
32
51
00
00
52
00
00
53
04
04
54
00
00
55
00
00
56, 57
Fixed data-1 (Initialized data)
58
00
00
Flange back adj.
59
83
83
CAP FG offset adj.
5A
0B
0A
Switching position adj.
5B
00
00
5C
Fixed data-1 (Initialized data)
5D
50
50
AFC f
0
adj.
5E
68
62
S VIDEO OUT Y level adj.
5F
62
62
S VIDEO OUT C level adj.
60, 61
Fixed data-1 (Initialized data)
62
B4
D7
REC Y current adj.
63
B4
D7
64 to 68
Fixed data-1 (Initialized data)
69
A0
A0
REC C/AFM current adj.
6A to 72
Fixed data-1 (Initialized data)
73
A6
A6
1.5 MHz deviation adj.
74
80
80
BPF f
0
adj.
75, 76
Fixed data-1 (Initialized data)
77
Fixed data-2
78 to 81
Fixed data-1 (Initialized data)
82
Fixed data-2
83 to 8E
Fixed data-1 (Initialized data)
8F
Fixed data-2
90
2B
2B
Auto white balance adj.
91
D0
E0
92
57
58
93
80
70
94
Fixed data-1 (Initialized data)
95
96
Fixed data-2
97, 98
Fixed data-1 (Initialized data)
99
Fixed data-2
9A to 9F
Fixed data-1 (Initialized data)
A0
Fixed data-2
A1
Fixed data-1 (Initialized data)
Click on the first or last page to see other CCD-TRV118 / CCD-TRV218E / CCD-TRV318 / CCD-TRV418 / CCD-TRV418E (serv.man2) service manuals if exist.