DOWNLOAD Sony SDM-S75A / SDM-S75D / SDM-S75E / SDM-S75F / SDM-S95A / SDM-S95AR / SDM-S95D / SDM-S95DR / SDM-S95E / SDM-S95ER / SDM-S95F / SDM-S95FR Service Manual ↓ Size: 681.13 KB | Pages: 23 in PDF or view online for FREE

                       

SDM-S75A,D,E,F/ SDM-S95A,AR,D,DR,E,ER,F,FR (E)

 

13

 

 
To go to “Service Mode”, please do the following procedures. 

1. Turn off the power. 
2. Turn on the power while pressing and holding the “

↓” key simultaneously. 

3. Press “MENU” key. 
4. Select “S” on the left side of displayed OSD menu bar. 

 
 

 
「COLOR TEMP」 
You can set color temperature (Factory Setting Area). 
 
「INITIAL EEPROM」 
You can initialize micro computer data.    Therefore, COLOR TEMP data becomes the default “128”. User table 
data is reset. 
 
「CLR. ETI」 
ETI is reset, “0 H”. 
 
「AGING」 
You can change aging status ON/OFF.    Default is OFF. 
 
「WHITE BALANCE」 
There are ADC（Analogue Digital Converter）  calibration function and ADC MANUAL calibration function. 
ADC calibration function adjustment is required when A (Main) board is replaced.    Bias is usually input on 
supplied service boards.    MANUAL calibration function is rarely used. 
* When ADC calibration is enforced, please calibrate with WHITE WINDOW pattern of Analogue VGA signal. 

** Input Signal: 31.4kHz, 600×480/60Hz and 0.73V

P-P     

(75

Ω terminate) 

 
「DEFAULT TIMING」 
You can select 1152×870 or 1152×864.    Default is 1152×870. 
 
「MODULE」 
You can select 

γ (table) corresponded to each module. 

When you replace A board or Panel, it is required to set the Panel inch size and the Panel maker name on 
selecting “MODULE”.   

 

                       

SDM-S75A,D,E,F/ SDM-S95A,AR,D,DR,E,ER,F,FR (E)

 

14

                       

SDM-S75A,D,E,F/ SDM-S95A,AR,D,DR,E,ER,F,FR (E)

 

14

 

                       

SDM-S75A,D,E,F/ SDM-S95A,AR,D,DR,E,ER,F,FR (E)

 

15

                       

SDM-S75A,D,E,F/ SDM-S95A,AR,D,DR,E,ER,F,FR (E)

 

16

 

1) Enter the service mode of this unit by turning on the 

power while pressing and holding the "↓" key 
simultaneously. 

2) Press "MENU" key----MAINTAIN. 
3) Press "OK" key to enter the service menu. 
4) Select the desired function. 
5) Press the "MENU" key to exit OSD. 
6) Turn off the power and then turn on it again. The 

monitor then enters the normal mode. 
To enter the service again, repeat the procedure 
described above. 

W/B readjustment is required after the panel, board 
and microcomputer are replaced. However, be sure to 
perform aging for more than 30 minutes for RGB 
reset before W/B adjustment. 

1) Prepare timing and pattern data for a signal 

generator according to the Sony timing specifications. 

2) Connect a monitor video cable to the signal 

generator. 

3) Put Color Analyzer (ex. CA-110) 50cm away from the 

monitor, specify it vertically in the center of the display, 
and adjust the focus to the optimum level using an 
eyepiece. 

4) Put the monitor and Color Analyzer (ex. CA-110) in a 

light-shielded room. 

5) Set up [SERVICE MODE] of the monitor.

 

Data is manually set to improve the productivity. The 
brightness, contrast, and backlight are set to 50, 70 and 
100 respectively. After that, the default data of the color 
temperature to be adjusted is set. 

Warm up for 30 minutes before performing any 
adjustment. 

a. Display SMPTE at SXGA/60Hz (Input level 0.73V). 
b. Set up [SERVICE MODE]. 
c. Click "INITIAL EEPROM" and again setup Service 

Mode. 

d. Click "WHITE BALANCE" and then select “AUTO”. 

 

a. Select "9300K" in "COLOR TEMP" and enter. 
b. Use a 35% (89Gray) IRE white video field in the 

primary mode. 

c. Adjust "SUB CONTRAST" to secure the color 

temperature. 

d. Press "MENU" key to exit adjust mode. 

a. Select "6500K" in "COLOR TEMP" and enter. 
b. Repeat the adjustment procedure as steps b to d at 

9300K.  

.