Sony CPD-200GS (serv.man2) Service Manual ▷ View online
— 17 —
CPD-200GS
Vertical and Horizontal Position and Size
Specification
2
1
2
1
G
G
R
B
3. Receive White cross-hatch.
4. Adjust HMC and VMC at six-pole magnet.
4. Adjust HMC and VMC at six-pole magnet.
< 6 Pole Magnet>
5. Receive R.B. cross-hatch.
6. Adjust H.TILT by swinging the DY neck right and left.
7. Adjust XCV with XCV core.
6. Adjust H.TILT by swinging the DY neck right and left.
7. Adjust XCV with XCV core.
XCV movement
R
B
B
R
R
B
b
b
a
a
A
B
A 0.24mm
B 0.30mm
B 0.30mm
B
A
Focus (V)
FBT
YCH
TLV
XCV
Horizontal and Vertical
a < 2.5 mm
b < 2.5 mm
b < 2.5 mm
A B
202 270
2
7
0
4
6
1
5
3
9
8
12
11
YBH-B
YBH-T
CBH-RT
MBH-RT
APH-R
MBH-RB
CBH-RB
CBH-LB
MBH-LB
APH-L
MBH-LT
CBH-LT
Adjust each misconvergence point in sequence.
H STAT
11. Digital Convergence Adjustment
A. Horizontal Convergence
2
7
0
4
6
1
5
3
9
8
12
11
V STAT-B
V STAT-T
CCV-RT
MCV-RT
XBV-R
MCV-RB
CCV-RB
CCV-LB
MCV-LB
XBV-L
MCV-LT
CCV-LT
Adjust each misconvergence point in sequence.
V STAT
8. Adjust V.TILT with TLV VR.
TLV movement
9. Adjust Y.CROSS with YCH VR.
YCH movement
10. Paint lock the four-pole and six-pole Mg.
<VR Adjustment on DY>
<Zero Position NECK Ass'y>
Purity
4-Pole Mg 6-Pole Mg
0.30mm
0.30mm
0.30mm
R
B
B
R
B
B
R
Convergence Specification
Focus adjustment
Adjust focus (V) and focus (H) for optimum focus.
B. Vertical Convergence
C. Repeat the procedure of A and B so that the
convergence of the whole screen is within the
specification.
convergence of the whole screen is within the
specification.
Focus (H)
Focus (v)
Focus (V)
FBT
Focus (H)
— 18 —
CPD-200GS
5-2. CIRCUIT BOARDS LOCATION
Note:
• All capacitors are in
µ
F unless otherwise noted. pF:
µµ
F
50 WV or less are not indicated except for electrolytic.
• Indication of resistance, which does not have one for rating
electrical power, is as follows.
• Indication of resistance, which does not have one for rating
electrical power, is as follows.
• All resistors are in ohms.
•
•
f
: nonflammable resistor.
•
F
:
fusible resistor.
•
∆
: internal component.
•
p
:
panel designation and adjustment for repair.
•
e :
earth-ground.
•
E :
earth-chassis.
• The components identified by
[ in this basic schematic
diagram have been carefully factory-selected for each set
in order to satisfy regulations regarding X-ray radiation.
Should replacement be required, replace only with the
value originally used.
• When replacing components identified by
in order to satisfy regulations regarding X-ray radiation.
Should replacement be required, replace only with the
value originally used.
• When replacing components identified by
]
,
make the necessary
adjustments by using RV501 (
[) as indicated. (See page 15)
• All variable and adjustable resistors have characteristic curve B,
unless otherwise noted.
unless otherwise noted.
• When replacing parts shown in the table below,
be sure to perform the safety related adjustment.
be sure to perform the safety related adjustment.
Part Replaced (
[)
RV501
Part Replaced (
])
•
All voltages are in volts.
•
Readings are taken with a 10
ΜΩ
digital multimeter
•
Readings are taken with a color-bar signal input.
•
Voltage variations may be noted due to normal
production tolerances.
production tolerances.
• *
: Cannot be measured.
•
Circled numbers are waveform references.
•
: B +bus.
•
: B - bus.
Pitch: 5 mm
Rating electrical power 1/4 W (CHIP: 1/10 W)
Rating electrical power 1/4 W (CHIP: 1/10 W)
Note: The components identified by shading and
mark
¡
are critical for safety. Replace only
with part number specified.
Note: Les composants identifies per un trame et une
marque
marque
¡
sont critiques pour la securite. Ne les
remplacer que par une piece portant le numero specifie.
5-3. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS
D - BOARD
RV501, T501, R545, R546, R548,
R550, R547, R549, R552, D517,
IC605, IC901, C540, C542, C544,
C541, C535, IC501, C558, R567,
R564, C555, C553, C554, C561
R550, R547, R549, R552, D517,
IC605, IC901, C540, C542, C544,
C541, C535, IC501, C558, R567,
R564, C555, C553, C554, C561
D
A
J
Click on the first or last page to see other CPD-200GS (serv.man2) service manuals if exist.